Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Wiley eBooks

Flux Modulation Scheme ( FMS )

Yi Zhang, Hui Dong, Hans-Joachim Krause, Guofeng Zhang, Xiaoming Xie

Published May 29, 2020• 0 citations
Publisher

Abstract

This chapter introduces the “mixed bias mode” and discusses the flux modulation scheme (FMS). It revisits the FMS by analyzing the bias mode and the transfer characteristics of a step-up transformer. The readout schemes share the common idea of modifying the Superconducting QUantum Interference Device (SQUID) input circuit to enhance the SQUID's apparent transfer coefficient at the input terminals of the preamplifier. The SQUID is matched to a preamplifier via a four-terminal step-up transformer. The “head stage” of the FMS is essentially an AC circuit and is calibrated by the amplitude- and phase-to-frequency transfer characteristics of the transformer. The two imperfections for SQUID operation in FMS, one is the shunt effect of primary winding and the other is nonlinear transformation from primary winding to secondary winding, to reduce benefit of the transformer.

DOI
10.1002/9783527816514.ch7

Related papers

Flux modulation scheme for direct current SQUID readout revisited

Tao Hong, Hai Wang, Yi Zhang +5 more

The flux modulation scheme (FMS) is the standard readout technique of dc SQUIDs, where a step-up transformer links the SQUID to the preamplifier. The transformer's primary winding shunts the SQUID via a large capacitor while the secondary winding connects it to the preamplifier. A modulation flux having a frequency of typically 100 kHz generates an ac voltage across the SQUID, stepped up by the transformer. The SQUID with FMS is customarily operated in the current bias mode, because a constant dc bias current flows only through the SQUID due to the capacitor isolation. With FMS, however, the transformer ac shunts the SQUID so that in reality the operating mode is neither purely current-biased nor voltage-biased but rather nominal current-biased or “mixed biased.” Our objective is to experimentally investigate the consequences of ac shunting of the dc SQUID in FMS and the transformer's transfer characteristics. For different shunt values we measure the change in the SQUID bias current due to the ac shunt using another SQUID in the two-stage readout scheme, and simultaneously monitor the SQUID output voltage signal. We then explain our measurements by a simplified graphic analysis of SQUID intrinsic current-voltage (I–V) characteristics. Since the total current flowing through the SQUID is not constant due to the shunting effect of the transformer, the amplitude of SQUID flux-to-voltage characteristics V(Φ) is less as compared to the direct readout scheme (DRS). Furthermore, we analyze and compare V(Φ) obtained by DRS and FMS. We show that in FMS, the transfer characteristics of the SQUID circuit also depend on the isolation capacitance and the dynamic resistance of the SQUID.

Applied Physics Letters•Feb 8, 2016•4 citations

Flux Feedback Concepts and Parallel Feedback Circuit

Yi Zhang, Hui Dong, Hans‐Joachim Krause +2 more

This chapter highlights the direct readout scheme with feedback circuits in the “head stage” at cryogenic temperature. Generally, there are two typical kinds of feedback circuits, i.e. the parallel feedback circuit (PFC) and series feedback coil (circuit) (SFC). In a sense, the modified SQUID's “head stage” with PFC (or SFC) can be regarded as a new device with apparent parameters. The chapter discusses the apparent parameters of the SQUID with PFC, e.g. the change in the SQUID's transfer coefficient at the working point. It qualitatively analyzes the PFC in current bias mode, namely, the additional positive feedback scheme. The chapter also focuses on the flux noise contribution of the preamplifier and discusses the flux noise contribution from the Johnson voltage noise. Indeed, for a stable low-noise SQUID readout technique, operating a SQUID with a PFC in range, or possibly in the transition range is recommended.

Wiley eBooks•May 29, 2020•0 citations

Analyses of the “Series Feedback Coil (Circuit)” ( SFC )

Yi Zhang, Hui Dong, Hans‐Joachim Krause +2 more

This chapter thoroughly analyzes the effects of Series Feedback Coil (Circuit) (SFC). In current bias mode, the chapter begins with a model of “two voltages in series” to understand the principle of the SFC. In voltage bias mode, the SFC increases the apparent flux-to-current transfer coefficient of a Superconducting QUantum Interference Device (SQUID), thus reducing noise contribution of the preamplifier. For both bias modes, the SFC reduces the apparent dynamic resistance. In current bias mode, the readout quantity is the voltage signal of the SQUID. In practice, the choice between parallel feedback circuit (PFC) and SFC depends not only on the preamplifier but also on the SQUID parameters. The combination of PFC and SFC in voltage bias mode can be abbreviated as PSFC, which was also called SQUID bootstrap circuit. The chapter demonstrates the PSFC in voltage bias mode and observes different behavior of PSFC at different working points.

Wiley eBooks•May 29, 2020•0 citations

Study on Noise Matching Between SQUID Sensor and Its Readout Electronics

Hai Wang, Hua Chen, Xiangyan Kong +3 more

Noise matching between superconducting quantum interference device (SQUID) sensor and readout electronics has always been an important problem. Conventionally, in order to avoid the hysteresis, SQUIDs should be operated in the range of βccis the Stewart-McCumber parameter. Recently, Liu et al. extended the SQUID operating area to βc > 1 due to a large noise parameter Γ*. When βc> 1, SQUID exhibits a large ∂V/∂Φ, which is beneficial in reducing the noise contribution of the readout electronics, δΦe. In this work, we compare the SQUID system noise δΦsmeasured with four different readout electronics. Here, the four readout electronics employed are as follows: 1) the flux modulation scheme (FMS); 2) the direct readout scheme (DRS), which uses six parallel connected bipolar transistor as its preamplifier (DRS-PCBT); 3) the DRS, which uses a single preamplifier AD797 (DRS-AD797); and 4) the two-stage scheme. The preamplifier voltage noise of DRS-PCBT and DRS-AD797 are about 0.4 nV/√Hz and 0.9 nV/√Hz, respectively. For a two-stage scheme, the equivalent flux noise reaches about 0.25 μΦ0/√Hz, the measured SQUID intrinsic noise, δΦi, will dominate δΦs. In other readout schemes, however, δΦsdepends on the value of βc. Finally, we found that FMS is suitable to match SQUIDs with βccc> 3.

IEEE Transactions on Applied Superconductivity•Nov 30, 2016•4 citations

Introduction

Yi Zhang, Hui Dong, Hans‐Joachim Krause +2 more

According to the type of superconducting material used, Superconducting QUantum Interference Devices (SQUID) can be divided into two groups: the low-temperature superconducting and the high-temperature superconducting SQUID. Josephson junction (JJ) is the key element of SQUIDs. JJs are analyzed with the resistively and capacitively shunted junction (RCSJ) model, thus introducing two important parameters: the Stewart–McCumber parameter and the thermal rounding parameter. For readout electronics, the DC SQUID is regarded as dynamic resistance Rd modulated by the flux threading into the SQUID loop. In the case of a direct readout scheme where the SQUID directly connects to a preamplifier, the electronics noise is usually much larger than the SQUID intrinsic noise. The techniques of additional positive feedback, bias current feedback, and noise cancellation are categorized and discussed. This chapter introduces two special DC SQUID readout schemes, the two-stage scheme and the double relaxation oscillation (DROS) scheme.

Wiley eBooks•May 29, 2020•0 citations

Improved dc SQUID read-out electronics with low 1/f noise preamplifier

D. Drung

An improved read-out electronics without flux modulation for dc superconducting quantum interference devices (dc SQUIDs) is presented where the preamplifier is directly coupled to the SQUID. Compared to our previous designs, the 1/f voltage and current noise levels of the preamplifier were reduced by about a factor of 4 (rms) by using bipolar matched transistors instead of operational amplifiers at the input. Three types of flux-locked-loop electronics were developed and successfully tested: a low-power (120 mW) version for large multichannel arrays, a high-speed version with a 15 MHz bandwidth and a very fast (300 ns) reset mode, and a low-noise (0.44 nV/Hz) version with a fast and precise bias reversal circuit. The flux-locked-loop electronics are compatible with each other, so that only one type of low-power (180 mW) control unit is required to operate them. All essential specifications of practical SQUID systems (noise, dynamic behavior, and temperature stability) were determined by using liquid-helium and liquid-nitrogen cooled SQUIDs, respectively.

Review of Scientific Instruments•Nov 1, 1997•43 citations
This chapter introduces the “mixed bias mode” and discusses the flux modulation scheme (FMS). It revisits the FMS by analyzing the bias mode and the transfer characteristics of a step-up transformer. The readout schemes share the common idea of modifying the Superconducting QUantum Interference Device (SQUID) input circuit to enhance the SQUID's apparent transfer coefficient at the input terminals of the preamplifier. The SQUID is matched to a preamplifier via a four-terminal step-up transformer. The “head stage” of the FMS is essentially an AC circuit and is calibrated by the amplitude- and phase-to-frequency transfer characteristics of the transformer. The two imperfections for SQUID operation in FMS, one is the shunt effect of primary winding and the other is nonlinear transformation from primary winding to secondary winding, to reduce benefit of the transformer.
The flux modulation scheme (FMS) is the standard readout technique of dc SQUIDs, where a step-up transformer links the SQUID to the preamplifier. The transformer's primary winding shunts the SQUID via a large capacitor while the secondary winding connects it to the preamplifier. A modulation flux having a frequency of typically 100 kHz generates an ac voltage across the SQUID, stepped up by the transformer. The SQUID with FMS is customarily operated in the current bias mode, because a constant dc bias current flows only through the SQUID due to the capacitor isolation. With FMS, however, the transformer ac shunts the SQUID so that in reality the operating mode is neither purely current-biased nor voltage-biased but rather nominal current-biased or “mixed biased.” Our objective is to experimentally investigate the consequences of ac shunting of the dc SQUID in FMS and the transformer's transfer characteristics. For different shunt values we measure the change in the SQUID bias current due to the ac shunt using another SQUID in the two-stage readout scheme, and simultaneously monitor the SQUID output voltage signal. We then explain our measurements by a simplified graphic analysis of SQUID intrinsic current-voltage (I–V) characteristics. Since the total current flowing through the SQUID is not constant due to the shunting effect of the transformer, the amplitude of SQUID flux-to-voltage characteristics V(Φ) is less as compared to the direct readout scheme (DRS). Furthermore, we analyze and compare V(Φ) obtained by DRS and FMS. We show that in FMS, the transfer characteristics of the SQUID circuit also depend on the isolation capacitance and the dynamic resistance of the SQUID.
This chapter highlights the direct readout scheme with feedback circuits in the “head stage” at cryogenic temperature. Generally, there are two typical kinds of feedback circuits, i.e. the parallel feedback circuit (PFC) and series feedback coil (circuit) (SFC). In a sense, the modified SQUID's “head stage” with PFC (or SFC) can be regarded as a new device with apparent parameters. The chapter discusses the apparent parameters of the SQUID with PFC, e.g. the change in the SQUID's transfer coefficient at the working point. It qualitatively analyzes the PFC in current bias mode, namely, the additional positive feedback scheme. The chapter also focuses on the flux noise contribution of the preamplifier and discusses the flux noise contribution from the Johnson voltage noise. Indeed, for a stable low-noise SQUID readout technique, operating a SQUID with a PFC in range, or possibly in the transition range is recommended.
This chapter thoroughly analyzes the effects of Series Feedback Coil (Circuit) (SFC). In current bias mode, the chapter begins with a model of “two voltages in series” to understand the principle of the SFC. In voltage bias mode, the SFC increases the apparent flux-to-current transfer coefficient of a Superconducting QUantum Interference Device (SQUID), thus reducing noise contribution of the preamplifier. For both bias modes, the SFC reduces the apparent dynamic resistance. In current bias mode, the readout quantity is the voltage signal of the SQUID. In practice, the choice between parallel feedback circuit (PFC) and SFC depends not only on the preamplifier but also on the SQUID parameters. The combination of PFC and SFC in voltage bias mode can be abbreviated as PSFC, which was also called SQUID bootstrap circuit. The chapter demonstrates the PSFC in voltage bias mode and observes different behavior of PSFC at different working points.
Noise matching between superconducting quantum interference device (SQUID) sensor and readout electronics has always been an important problem. Conventionally, in order to avoid the hysteresis, SQUIDs should be operated in the range of βccis the Stewart-McCumber parameter. Recently, Liu et al. extended the SQUID operating area to βc > 1 due to a large noise parameter Γ*. When βc> 1, SQUID exhibits a large ∂V/∂Φ, which is beneficial in reducing the noise contribution of the readout electronics, δΦe. In this work, we compare the SQUID system noise δΦsmeasured with four different readout electronics. Here, the four readout electronics employed are as follows: 1) the flux modulation scheme (FMS); 2) the direct readout scheme (DRS), which uses six parallel connected bipolar transistor as its preamplifier (DRS-PCBT); 3) the DRS, which uses a single preamplifier AD797 (DRS-AD797); and 4) the two-stage scheme. The preamplifier voltage noise of DRS-PCBT and DRS-AD797 are about 0.4 nV/√Hz and 0.9 nV/√Hz, respectively. For a two-stage scheme, the equivalent flux noise reaches about 0.25 μΦ0/√Hz, the measured SQUID intrinsic noise, δΦi, will dominate δΦs. In other readout schemes, however, δΦsdepends on the value of βc. Finally, we found that FMS is suitable to match SQUIDs with βccc> 3.
According to the type of superconducting material used, Superconducting QUantum Interference Devices (SQUID) can be divided into two groups: the low-temperature superconducting and the high-temperature superconducting SQUID. Josephson junction (JJ) is the key element of SQUIDs. JJs are analyzed with the resistively and capacitively shunted junction (RCSJ) model, thus introducing two important parameters: the Stewart–McCumber parameter and the thermal rounding parameter. For readout electronics, the DC SQUID is regarded as dynamic resistance Rd modulated by the flux threading into the SQUID loop. In the case of a direct readout scheme where the SQUID directly connects to a preamplifier, the electronics noise is usually much larger than the SQUID intrinsic noise. The techniques of additional positive feedback, bias current feedback, and noise cancellation are categorized and discussed. This chapter introduces two special DC SQUID readout schemes, the two-stage scheme and the double relaxation oscillation (DROS) scheme.
An improved read-out electronics without flux modulation for dc superconducting quantum interference devices (dc SQUIDs) is presented where the preamplifier is directly coupled to the SQUID. Compared to our previous designs, the 1/f voltage and current noise levels of the preamplifier were reduced by about a factor of 4 (rms) by using bipolar matched transistors instead of operational amplifiers at the input. Three types of flux-locked-loop electronics were developed and successfully tested: a low-power (120 mW) version for large multichannel arrays, a high-speed version with a 15 MHz bandwidth and a very fast (300 ns) reset mode, and a low-noise (0.44 nV/Hz) version with a fast and precise bias reversal circuit. The flux-locked-loop electronics are compatible with each other, so that only one type of low-power (180 mW) control unit is required to operate them. All essential specifications of practical SQUID systems (noise, dynamic behavior, and temperature stability) were determined by using liquid-helium and liquid-nitrogen cooled SQUIDs, respectively.