According to the type of superconducting material used, Superconducting QUantum Interference Devices (SQUID) can be divided into two groups: the low-temperature superconducting and the high-temperature superconducting SQUID. Josephson junction (JJ) is the key element of SQUIDs. JJs are analyzed with the resistively and capacitively shunted junction (RCSJ) model, thus introducing two important parameters: the Stewart–McCumber parameter and the thermal rounding parameter. For readout electronics, the DC SQUID is regarded as dynamic resistance Rd modulated by the flux threading into the SQUID loop. In the case of a direct readout scheme where the SQUID directly connects to a preamplifier, the electronics noise is usually much larger than the SQUID intrinsic noise. The techniques of additional positive feedback, bias current feedback, and noise cancellation are categorized and discussed. This chapter introduces two special DC SQUID readout schemes, the two-stage scheme and the double relaxation oscillation (DROS) scheme.
According to the type of superconducting material used, Superconducting QUantum Interference Devices (SQUID) can be divided into two groups: the low-temperature superconducting and the high-temperature superconducting SQUID. Josephson junction (JJ) is the key element of SQUIDs. JJs are analyzed with the resistively and capacitively shunted junction (RCSJ) model, thus introducing two important parameters: the Stewart–McCumber parameter and the thermal rounding parameter. For readout electronics, the DC SQUID is regarded as dynamic resistance Rd modulated by the flux threading into the SQUID loop. In the case of a direct readout scheme where the SQUID directly connects to a preamplifier, the electronics noise is usually much larger than the SQUID intrinsic noise. The techniques of additional positive feedback, bias current feedback, and noise cancellation are categorized and discussed. This chapter introduces two special DC SQUID readout schemes, the two-stage scheme and the double relaxation oscillation (DROS) scheme.
Dependence of SQUID Intrinsic Flux Noise on Stewart–McCumber Parameter βc of Josephson Junction
It is known that three superconducting quantum interference device (SQUID) parameters, namely, the intrinsic flux noise δΦs, the flux-to-voltage transfer coefficient ∂V/∂Φ, and the dynamic resistance Rd, increase with increasing the Stewart- McCumber parameter βcof Josephson junction. It is very difficult to obtain the low values of δΦsfor a strongly damped SQUID due to its small ∂V/∂Φ. In this paper, we employ a two-stage scheme (TSS) to measure δΦsdirectly. Here, we use single chip readout electronics and a weakly damped SQUID with a βcof flux noise of the readout-SQUID system is about 4.8 μΦ0/√Hz 1.2, both acting as a readout-SQUID system (a preamplifier). The with a corner frequency of about 10 Hz. The front-end SQUID is coupled to the readout SQUID via the input coil with a mutual inductance of Mi. In our experiment, the flux gain for a readout SQUID, i.e., GΦ= Mi× (∂I/∂Φ)front-endis adjusted to be 20. Using the TSS, we measured δΦswith different βcchanging from 0.3 to 13.5 and found δΦsincreasing from 1.0 to 5.0 μΦ0/√Hz. We also discussed the relations between Ls, βc, and δΦsquantitatively. Finally, we proposed designing a suitable βcto match the preamplifier in a direct readout scheme to simplify a SQUID measurement system.
We have realized a two-stage integrated superconducting quantum interference device (SQUID) system with a closed loop bandwidth of 2.5 MHz, operated in a direct voltage readout mode. The corresponding flux slew rate was 1.3×105 Φ0/s and the measured white flux noise was 1.3 μΦ0/√Hz at 4.2 K. The system is based on a conventional dc SQUID with a double relaxation oscillation SQUID (DROS) as the second stage. Because of the large flux-to-voltage transfer, the sensitivity of the system is completely determined by the sensor SQUID and not by the DROS or the room-temperature preamplifier. Decreasing the Josephson junction area enables a further improvement of the sensitivity of the two-stage SQUID systems.
The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.
This chapter introduces two DC Superconducting QUantum Interference Device (SQUID) readout schemes, i.e. a two-stage scheme and a double relaxation oscillation (D-ROS), suitable for SQUID intrinsic noise observation. The two-stage readout scheme consists of a voltage-biased sensing SQUID and an ammeter with the reading SQUID. Intuitively, SQUIDs with two junctions maintain hysteresis, and their I–V characteristics should contain information on the applied flux. D-ROS, originally called balanced ROS, consisting of two hysteretic DC SQUIDs in series, was developed to increase the transfer coefficient. In the original work, the signal flux was applied to both SQUIDs; i.e. the roles of the two SQUIDs, where one is reading and the other is sensing, can be exchanged. In contrast to balanced ROS, the functions of the two SQUIDs are well defined in D-ROS; i.e. one is the sensing SQUID, and the other is the reading SQUID, similar to two-stage scheme.
We propose a readout scheme for high-T c dc-SQUIDs (superconducting quantum interference devices) with alternating current bias and synchronized offset flux. By use of this scheme, low-frequency noise due to critical current fluctuations, which exist in grain boundary junctions, can be canceled. The readout electronics are simple and operation parameters requiring adjustment are minimized. The ac bias scheme has been applied to YBCO step-junction SQUIDs, where partial reduction of the equivalent flux noise below 100 Hz is observed.
We experimentally studied two important parameters of helium-cooled superconducting quantum interference devices (SQUIDs) in the voltage bias mode: the dynamic resistance Rd and the flux-to-current transfer coefficient ∂i/∂Φ, with different junction shunt resistors RJ. We investigated a voltage-biased SQUID using the direct readout current-to-voltage converter scheme involving an operational amplifier. At higher RJ, the flux-to-voltage conversion coefficient ∂V/∂Φ becomes sufficiently large to effectively suppress the room-temperature amplifier's noise without any need for additional feedback circuits. The McCumber parameter limits the rise of ∂V/∂Φ. We discuss the performance of voltage-biased SQUIDs at different effective McCumber parameters.