Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Wiley eBooks

Flux Feedback Concepts and Parallel Feedback Circuit

Yi Zhang, Hui Dong, Hans‐Joachim Krause, Guofeng Zhang, Xiaoming Xie

Published May 29, 2020• 0 citations
Publisher

Abstract

This chapter highlights the direct readout scheme with feedback circuits in the “head stage” at cryogenic temperature. Generally, there are two typical kinds of feedback circuits, i.e. the parallel feedback circuit (PFC) and series feedback coil (circuit) (SFC). In a sense, the modified SQUID's “head stage” with PFC (or SFC) can be regarded as a new device with apparent parameters. The chapter discusses the apparent parameters of the SQUID with PFC, e.g. the change in the SQUID's transfer coefficient at the working point. It qualitatively analyzes the PFC in current bias mode, namely, the additional positive feedback scheme. The chapter also focuses on the flux noise contribution of the preamplifier and discusses the flux noise contribution from the Johnson voltage noise. Indeed, for a stable low-noise SQUID readout technique, operating a SQUID with a PFC in range, or possibly in the transition range is recommended.

DOI
10.1002/9783527816514.ch8

Related papers

Analyses of the “Series Feedback Coil (Circuit)” ( SFC )

Yi Zhang, Hui Dong, Hans‐Joachim Krause +2 more

This chapter thoroughly analyzes the effects of Series Feedback Coil (Circuit) (SFC). In current bias mode, the chapter begins with a model of “two voltages in series” to understand the principle of the SFC. In voltage bias mode, the SFC increases the apparent flux-to-current transfer coefficient of a Superconducting QUantum Interference Device (SQUID), thus reducing noise contribution of the preamplifier. For both bias modes, the SFC reduces the apparent dynamic resistance. In current bias mode, the readout quantity is the voltage signal of the SQUID. In practice, the choice between parallel feedback circuit (PFC) and SFC depends not only on the preamplifier but also on the SQUID parameters. The combination of PFC and SFC in voltage bias mode can be abbreviated as PSFC, which was also called SQUID bootstrap circuit. The chapter demonstrates the PSFC in voltage bias mode and observes different behavior of PSFC at different working points.

Wiley eBooks•May 29, 2020•0 citations

Introduction

Yi Zhang, Hui Dong, Hans‐Joachim Krause +2 more

According to the type of superconducting material used, Superconducting QUantum Interference Devices (SQUID) can be divided into two groups: the low-temperature superconducting and the high-temperature superconducting SQUID. Josephson junction (JJ) is the key element of SQUIDs. JJs are analyzed with the resistively and capacitively shunted junction (RCSJ) model, thus introducing two important parameters: the Stewart–McCumber parameter and the thermal rounding parameter. For readout electronics, the DC SQUID is regarded as dynamic resistance Rd modulated by the flux threading into the SQUID loop. In the case of a direct readout scheme where the SQUID directly connects to a preamplifier, the electronics noise is usually much larger than the SQUID intrinsic noise. The techniques of additional positive feedback, bias current feedback, and noise cancellation are categorized and discussed. This chapter introduces two special DC SQUID readout schemes, the two-stage scheme and the double relaxation oscillation (DROS) scheme.

Wiley eBooks•May 29, 2020•0 citations

Superconducting quantum interference device readout circuit with tunable feedback polarity

Xinyu Wu, Jianshe Liu, Wei Chen

Feedback circuits, which act as functional units in superconducting quantum interference device (SQUID) readout circuits, such as positive feedback circuits for suppressing the preamplifier noise contribution or negative feedback circuits for increasing the linear flux range of SQUID, enable SQUIDs to achieve high performance in practical applications. Integrating feedback circuits with different functions into a single SQUID chip contributes to the construction of highly compact SQUID electronics. Here, we propose a SQUID readout circuit with tunable feedback polarity (TFP). The switching of the feedback polarity is easily realized by applying a control current to the superconducting switches integrated into the SQUID chip. The enhancement of the flux-to-voltage transfer coefficient or the linear flux range depends on the choice of feedback polarity. In addition, we introduce a two-stage scheme to address the degraded noise performance induced by negative feedback. This work attempts to develop a compact and versatile architecture of SQUID readout by using a set of compatible superconducting technologies.

Review of Scientific Instruments•Sep 1, 2023•1 citation

Flux Modulation Scheme ( FMS )

Yi Zhang, Hui Dong, Hans-Joachim Krause +2 more

This chapter introduces the “mixed bias mode” and discusses the flux modulation scheme (FMS). It revisits the FMS by analyzing the bias mode and the transfer characteristics of a step-up transformer. The readout schemes share the common idea of modifying the Superconducting QUantum Interference Device (SQUID) input circuit to enhance the SQUID's apparent transfer coefficient at the input terminals of the preamplifier. The SQUID is matched to a preamplifier via a four-terminal step-up transformer. The “head stage” of the FMS is essentially an AC circuit and is calibrated by the amplitude- and phase-to-frequency transfer characteristics of the transformer. The two imperfections for SQUID operation in FMS, one is the shunt effect of primary winding and the other is nonlinear transformation from primary winding to secondary winding, to reduce benefit of the transformer.

Wiley eBooks•May 29, 2020•0 citations

A Practical Two-Stage SQUID Readout Circuit Improved With Proportional Feedback Schemes

Yongliang Wang, Guofeng Zhang, Shulin Zhang +4 more

Nonlinearity with multiple working points limits the practical applications of a two-stage superconducting quantum interference device (SQUID) readout circuit, which is promising for low-noise performance. To solve this problem, we proposed a simple two-stage SQUID readout circuit with two conventional dc SQUIDs improved with proportional feedback schemes, where transfer coefficient of the first-stage SQUID circuit is enhanced by additional positive feedback circuit; transfer characteristics of the second-stage SQUID circuit are linearized by an additional negative feedback circuit. Two proportional feedback schemes are cooperated together based on matching conditions to achieve both noise suppression and working point matching. Working principles were verified in experiment results. The overall transfer characteristics achieved have only one working point and are simply adjusted according to the voltage swing of an amplifier. Transfer coefficient of the first-stage SQUID circuit was raised up to 10 (20 dB), and the total flux noise of two-stage SQUID readout circuit was reduced below 1 μΦ0/√Hz, where Φ0= 2.07×10-15Wb. Our two-stage SQUID readout circuit is easy-to-operate and suited for high-performance practical SQUID systems.

IEEE Transactions on Applied Superconductivity•Jan 29, 2020•2 citations

An approach to optimization of the superconducting quantum interference device bootstrap circuit

Guofeng Zhang, Yi Zhang, Hui Dong +5 more

Recently, we demonstrated and analysed the superconducting quantum interference device (SQUID) bootstrap circuit (SBC). It is a direct readout scheme for dc SQUID in the voltage bias mode, permitting one to suppress the preamplifier noise. The SBC enables us to control the two key parameters of a voltage-biased SQUID: the flux-to-current transfer coefficient and the dynamic resistance. The flux-to-current, I-Phi, characteristics of SBC are made asymmetric by introducing the additional current feedback. Depending upon the choice of the working point, this feedback can be positive (working point W-2 on the steeper I-Phi slope) or negative (W-1 on the less steep slope). The dynamic resistance is controlled by the additional voltage feedback. In our publications to date we presented only the SBC operation at W-2, while in this paper we demonstrate operation at W-1 and show that also in this regime the preamplifier noise suppression is possible. We used a liquid-helium-cooled Nb SQUID with a loop inductance of 350 pH and attained white flux noise of 2.5 mu Phi(0) Hz(-1/2) both at W-2 and at W-1. In the latter case, the linear flux range exceeded one half-flux quantum Phi(0). This large linear range should lead to a significantly improved stability and slew rate of the system and also make the tolerable spread in circuit parameters much wider than in all SQUID direct readout schemes known to date. Consequently, operation in this regime opens a new path to possible SBC optimization.

Superconductor Science and Technology•Apr 21, 2011•11 citations
This chapter highlights the direct readout scheme with feedback circuits in the “head stage” at cryogenic temperature. Generally, there are two typical kinds of feedback circuits, i.e. the parallel feedback circuit (PFC) and series feedback coil (circuit) (SFC). In a sense, the modified SQUID's “head stage” with PFC (or SFC) can be regarded as a new device with apparent parameters. The chapter discusses the apparent parameters of the SQUID with PFC, e.g. the change in the SQUID's transfer coefficient at the working point. It qualitatively analyzes the PFC in current bias mode, namely, the additional positive feedback scheme. The chapter also focuses on the flux noise contribution of the preamplifier and discusses the flux noise contribution from the Johnson voltage noise. Indeed, for a stable low-noise SQUID readout technique, operating a SQUID with a PFC in range, or possibly in the transition range is recommended.
This chapter thoroughly analyzes the effects of Series Feedback Coil (Circuit) (SFC). In current bias mode, the chapter begins with a model of “two voltages in series” to understand the principle of the SFC. In voltage bias mode, the SFC increases the apparent flux-to-current transfer coefficient of a Superconducting QUantum Interference Device (SQUID), thus reducing noise contribution of the preamplifier. For both bias modes, the SFC reduces the apparent dynamic resistance. In current bias mode, the readout quantity is the voltage signal of the SQUID. In practice, the choice between parallel feedback circuit (PFC) and SFC depends not only on the preamplifier but also on the SQUID parameters. The combination of PFC and SFC in voltage bias mode can be abbreviated as PSFC, which was also called SQUID bootstrap circuit. The chapter demonstrates the PSFC in voltage bias mode and observes different behavior of PSFC at different working points.
According to the type of superconducting material used, Superconducting QUantum Interference Devices (SQUID) can be divided into two groups: the low-temperature superconducting and the high-temperature superconducting SQUID. Josephson junction (JJ) is the key element of SQUIDs. JJs are analyzed with the resistively and capacitively shunted junction (RCSJ) model, thus introducing two important parameters: the Stewart–McCumber parameter and the thermal rounding parameter. For readout electronics, the DC SQUID is regarded as dynamic resistance Rd modulated by the flux threading into the SQUID loop. In the case of a direct readout scheme where the SQUID directly connects to a preamplifier, the electronics noise is usually much larger than the SQUID intrinsic noise. The techniques of additional positive feedback, bias current feedback, and noise cancellation are categorized and discussed. This chapter introduces two special DC SQUID readout schemes, the two-stage scheme and the double relaxation oscillation (DROS) scheme.
Feedback circuits, which act as functional units in superconducting quantum interference device (SQUID) readout circuits, such as positive feedback circuits for suppressing the preamplifier noise contribution or negative feedback circuits for increasing the linear flux range of SQUID, enable SQUIDs to achieve high performance in practical applications. Integrating feedback circuits with different functions into a single SQUID chip contributes to the construction of highly compact SQUID electronics. Here, we propose a SQUID readout circuit with tunable feedback polarity (TFP). The switching of the feedback polarity is easily realized by applying a control current to the superconducting switches integrated into the SQUID chip. The enhancement of the flux-to-voltage transfer coefficient or the linear flux range depends on the choice of feedback polarity. In addition, we introduce a two-stage scheme to address the degraded noise performance induced by negative feedback. This work attempts to develop a compact and versatile architecture of SQUID readout by using a set of compatible superconducting technologies.
This chapter introduces the “mixed bias mode” and discusses the flux modulation scheme (FMS). It revisits the FMS by analyzing the bias mode and the transfer characteristics of a step-up transformer. The readout schemes share the common idea of modifying the Superconducting QUantum Interference Device (SQUID) input circuit to enhance the SQUID's apparent transfer coefficient at the input terminals of the preamplifier. The SQUID is matched to a preamplifier via a four-terminal step-up transformer. The “head stage” of the FMS is essentially an AC circuit and is calibrated by the amplitude- and phase-to-frequency transfer characteristics of the transformer. The two imperfections for SQUID operation in FMS, one is the shunt effect of primary winding and the other is nonlinear transformation from primary winding to secondary winding, to reduce benefit of the transformer.
Nonlinearity with multiple working points limits the practical applications of a two-stage superconducting quantum interference device (SQUID) readout circuit, which is promising for low-noise performance. To solve this problem, we proposed a simple two-stage SQUID readout circuit with two conventional dc SQUIDs improved with proportional feedback schemes, where transfer coefficient of the first-stage SQUID circuit is enhanced by additional positive feedback circuit; transfer characteristics of the second-stage SQUID circuit are linearized by an additional negative feedback circuit. Two proportional feedback schemes are cooperated together based on matching conditions to achieve both noise suppression and working point matching. Working principles were verified in experiment results. The overall transfer characteristics achieved have only one working point and are simply adjusted according to the voltage swing of an amplifier. Transfer coefficient of the first-stage SQUID circuit was raised up to 10 (20 dB), and the total flux noise of two-stage SQUID readout circuit was reduced below 1 μΦ0/√Hz, where Φ0= 2.07×10-15Wb. Our two-stage SQUID readout circuit is easy-to-operate and suited for high-performance practical SQUID systems.
Recently, we demonstrated and analysed the superconducting quantum interference device (SQUID) bootstrap circuit (SBC). It is a direct readout scheme for dc SQUID in the voltage bias mode, permitting one to suppress the preamplifier noise. The SBC enables us to control the two key parameters of a voltage-biased SQUID: the flux-to-current transfer coefficient and the dynamic resistance. The flux-to-current, I-Phi, characteristics of SBC are made asymmetric by introducing the additional current feedback. Depending upon the choice of the working point, this feedback can be positive (working point W-2 on the steeper I-Phi slope) or negative (W-1 on the less steep slope). The dynamic resistance is controlled by the additional voltage feedback. In our publications to date we presented only the SBC operation at W-2, while in this paper we demonstrate operation at W-1 and show that also in this regime the preamplifier noise suppression is possible. We used a liquid-helium-cooled Nb SQUID with a loop inductance of 350 pH and attained white flux noise of 2.5 mu Phi(0) Hz(-1/2) both at W-2 and at W-1. In the latter case, the linear flux range exceeded one half-flux quantum Phi(0). This large linear range should lead to a significantly improved stability and slew rate of the system and also make the tolerable spread in circuit parameters much wider than in all SQUID direct readout schemes known to date. Consequently, operation in this regime opens a new path to possible SBC optimization.