Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

An approach to optimization of the superconducting quantum interference device bootstrap circuit

Guofeng Zhang, Yi Zhang, Hui Dong, Hans‐Joachim Krause, Xiaoming Xie, Alex I. Braginski, Andreas Offenhäusser, Mianheng Jiang

Published Apr 21, 2011• 11 citations
Publisher

Abstract

Recently, we demonstrated and analysed the superconducting quantum interference device (SQUID) bootstrap circuit (SBC). It is a direct readout scheme for dc SQUID in the voltage bias mode, permitting one to suppress the preamplifier noise. The SBC enables us to control the two key parameters of a voltage-biased SQUID: the flux-to-current transfer coefficient and the dynamic resistance. The flux-to-current, I-Phi, characteristics of SBC are made asymmetric by introducing the additional current feedback. Depending upon the choice of the working point, this feedback can be positive (working point W-2 on the steeper I-Phi slope) or negative (W-1 on the less steep slope). The dynamic resistance is controlled by the additional voltage feedback. In our publications to date we presented only the SBC operation at W-2, while in this paper we demonstrate operation at W-1 and show that also in this regime the preamplifier noise suppression is possible. We used a liquid-helium-cooled Nb SQUID with a loop inductance of 350 pH and attained white flux noise of 2.5 mu Phi(0) Hz(-1/2) both at W-2 and at W-1. In the latter case, the linear flux range exceeded one half-flux quantum Phi(0). This large linear range should lead to a significantly improved stability and slew rate of the system and also make the tolerable spread in circuit parameters much wider than in all SQUID direct readout schemes known to date. Consequently, operation in this regime opens a new path to possible SBC optimization.

DOI
10.1088/0953-2048/24/6/065023

Related papers

Bias Reversal Technique in SQUID Bootstrap Circuit (SBC) Scheme

Liangliang Rong, Yi Zhang, Guofeng Zhang +5 more

Recently, a SQUID direct readout scheme called voltage-biased SQUID Bootstrap Circuit (SBC) is introduced to reduce preamplifier noise contribution. In this paper, we describe a concept of SBC with bias reversal technique which can suppress SQUID intrinsic 1/f noise. When applying a symmetrically rectangular voltage across SBC, two I-Φ characteristics appear at the amplifier output. In order to return to one I - Φ curve, a demodulation technique is required. Because of the asymmetry of typical SBC I-Φ curve, the demodulation method is realized by using a flux compensation of one half Φ0 flux shift. The output signal is then filtered and returned to one I-Φ curve for ordinary FLL readout. It was found, the reversal frequency fR can be dramatically enhanced when using a preamplifier consisting of two operational amplifiers. A planar Nb SQUID magnetometer with a loop-inductance of 350 pH, fR =50 kHz and a second order low pass filter with 10 kHz cut off frequency was employed in our experiment. Results prove the feasibility of SBC bias reversal method. Comparative experiment on noise performance will be carried out in further studies.

Physics Procedia•Jan 1, 2012•1 citation

A SQUID Bootstrap Circuit with a Large Parameter Tolerance

Guofeng Zhang, Yi Zhang, Hans‐Joachim Krause +3 more

The voltage biased (SQUID) bootstrap circuit (SBC) was recently introduced as an effective means to reduce the preamplifier noise contribution. We analyze the tolerances of the SBC noise suppression performance to spreads in SQUID and SBC circuit parameters. It is found that the tolerance to spread mainly caused by the integrated circuit fabrication process could be extended by a one-time adjustable current feedback. A helium-cooled niobium SQUID with a loop inductance of 350 pH is employed to experimentally verify the analysis. From this work, design criteria for fully integrated SBC devices with a high yield can be derived.

Chinese Physics Letters•Jan 1, 2013•5 citations

Analyses of the “Series Feedback Coil (Circuit)” ( SFC )

Yi Zhang, Hui Dong, Hans‐Joachim Krause +2 more

This chapter thoroughly analyzes the effects of Series Feedback Coil (Circuit) (SFC). In current bias mode, the chapter begins with a model of “two voltages in series” to understand the principle of the SFC. In voltage bias mode, the SFC increases the apparent flux-to-current transfer coefficient of a Superconducting QUantum Interference Device (SQUID), thus reducing noise contribution of the preamplifier. For both bias modes, the SFC reduces the apparent dynamic resistance. In current bias mode, the readout quantity is the voltage signal of the SQUID. In practice, the choice between parallel feedback circuit (PFC) and SFC depends not only on the preamplifier but also on the SQUID parameters. The combination of PFC and SFC in voltage bias mode can be abbreviated as PSFC, which was also called SQUID bootstrap circuit. The chapter demonstrates the PSFC in voltage bias mode and observes different behavior of PSFC at different working points.

Wiley eBooks•May 29, 2020•0 citations

Investigation and optimization of low-frequency noise performance in readout electronics of dc superconducting quantum interference device

Jing Bo Zhao, Yi Zhang, Yong-Ho Lee +1 more

We investigated and optimized the low-frequency noise characteristics of a preamplifier used for readout of direct current superconducting quantum interference devices (SQUIDs). When the SQUID output was detected directly using a room-temperature low-voltage-noise preamplifier, the low-frequency noise of a SQUID system was found to be dominated by the input current noise of the preamplifiers in case of a large dynamic resistance of the SQUID. To reduce the current noise of the preamplifier in the low-frequency range, we investigated the dependence of total preamplifier noise on the collector current and source resistance. When the collector current was decreased from 8.4 mA to 3 mA in the preamplifier made of 3 parallel SSM2220 transistor pairs, the low-frequency total voltage noise of the preamplifier (at 0.1 Hz) decreased by about 3 times for a source resistance of 30 Ω whereas the white noise level remained nearly unchanged. Since the relative contribution of preamplifier's input voltage and current noise is different depending on the dynamic resistance or flux-to-voltage transfer of the SQUID, the results showed that the total noise of a SQUID system at low-frequency range can be improved significantly by optimizing the preamplifier circuit parameters, mainly the collector current in case of low-noise bipolar transistor pairs.

Review of Scientific Instruments•May 1, 2014•19 citations

An insight into voltage-biased superconducting quantum interference devices

Chao Liu, Yi Zhang, Michael Mück +5 more

We experimentally studied two important parameters of helium-cooled superconducting quantum interference devices (SQUIDs) in the voltage bias mode: the dynamic resistance Rd and the flux-to-current transfer coefficient ∂i/∂Φ, with different junction shunt resistors RJ. We investigated a voltage-biased SQUID using the direct readout current-to-voltage converter scheme involving an operational amplifier. At higher RJ, the flux-to-voltage conversion coefficient ∂V/∂Φ becomes sufficiently large to effectively suppress the room-temperature amplifier's noise without any need for additional feedback circuits. The McCumber parameter limits the rise of ∂V/∂Φ. We discuss the performance of voltage-biased SQUIDs at different effective McCumber parameters.

Applied Physics Letters•Nov 26, 2012•20 citations

Low-noise ultra-high-speed dc SQUID readout electronics

D. Drung, Colmar Hinnrichs, H.-J. Barthelmess

User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.

Superconductor Science and Technology•Feb 27, 2006•76 citations
Recently, we demonstrated and analysed the superconducting quantum interference device (SQUID) bootstrap circuit (SBC). It is a direct readout scheme for dc SQUID in the voltage bias mode, permitting one to suppress the preamplifier noise. The SBC enables us to control the two key parameters of a voltage-biased SQUID: the flux-to-current transfer coefficient and the dynamic resistance. The flux-to-current, I-Phi, characteristics of SBC are made asymmetric by introducing the additional current feedback. Depending upon the choice of the working point, this feedback can be positive (working point W-2 on the steeper I-Phi slope) or negative (W-1 on the less steep slope). The dynamic resistance is controlled by the additional voltage feedback. In our publications to date we presented only the SBC operation at W-2, while in this paper we demonstrate operation at W-1 and show that also in this regime the preamplifier noise suppression is possible. We used a liquid-helium-cooled Nb SQUID with a loop inductance of 350 pH and attained white flux noise of 2.5 mu Phi(0) Hz(-1/2) both at W-2 and at W-1. In the latter case, the linear flux range exceeded one half-flux quantum Phi(0). This large linear range should lead to a significantly improved stability and slew rate of the system and also make the tolerable spread in circuit parameters much wider than in all SQUID direct readout schemes known to date. Consequently, operation in this regime opens a new path to possible SBC optimization.
Recently, a SQUID direct readout scheme called voltage-biased SQUID Bootstrap Circuit (SBC) is introduced to reduce preamplifier noise contribution. In this paper, we describe a concept of SBC with bias reversal technique which can suppress SQUID intrinsic 1/f noise. When applying a symmetrically rectangular voltage across SBC, two I-Φ characteristics appear at the amplifier output. In order to return to one I - Φ curve, a demodulation technique is required. Because of the asymmetry of typical SBC I-Φ curve, the demodulation method is realized by using a flux compensation of one half Φ0 flux shift. The output signal is then filtered and returned to one I-Φ curve for ordinary FLL readout. It was found, the reversal frequency fR can be dramatically enhanced when using a preamplifier consisting of two operational amplifiers. A planar Nb SQUID magnetometer with a loop-inductance of 350 pH, fR =50 kHz and a second order low pass filter with 10 kHz cut off frequency was employed in our experiment. Results prove the feasibility of SBC bias reversal method. Comparative experiment on noise performance will be carried out in further studies.
The voltage biased (SQUID) bootstrap circuit (SBC) was recently introduced as an effective means to reduce the preamplifier noise contribution. We analyze the tolerances of the SBC noise suppression performance to spreads in SQUID and SBC circuit parameters. It is found that the tolerance to spread mainly caused by the integrated circuit fabrication process could be extended by a one-time adjustable current feedback. A helium-cooled niobium SQUID with a loop inductance of 350 pH is employed to experimentally verify the analysis. From this work, design criteria for fully integrated SBC devices with a high yield can be derived.
This chapter thoroughly analyzes the effects of Series Feedback Coil (Circuit) (SFC). In current bias mode, the chapter begins with a model of “two voltages in series” to understand the principle of the SFC. In voltage bias mode, the SFC increases the apparent flux-to-current transfer coefficient of a Superconducting QUantum Interference Device (SQUID), thus reducing noise contribution of the preamplifier. For both bias modes, the SFC reduces the apparent dynamic resistance. In current bias mode, the readout quantity is the voltage signal of the SQUID. In practice, the choice between parallel feedback circuit (PFC) and SFC depends not only on the preamplifier but also on the SQUID parameters. The combination of PFC and SFC in voltage bias mode can be abbreviated as PSFC, which was also called SQUID bootstrap circuit. The chapter demonstrates the PSFC in voltage bias mode and observes different behavior of PSFC at different working points.
We investigated and optimized the low-frequency noise characteristics of a preamplifier used for readout of direct current superconducting quantum interference devices (SQUIDs). When the SQUID output was detected directly using a room-temperature low-voltage-noise preamplifier, the low-frequency noise of a SQUID system was found to be dominated by the input current noise of the preamplifiers in case of a large dynamic resistance of the SQUID. To reduce the current noise of the preamplifier in the low-frequency range, we investigated the dependence of total preamplifier noise on the collector current and source resistance. When the collector current was decreased from 8.4 mA to 3 mA in the preamplifier made of 3 parallel SSM2220 transistor pairs, the low-frequency total voltage noise of the preamplifier (at 0.1 Hz) decreased by about 3 times for a source resistance of 30 Ω whereas the white noise level remained nearly unchanged. Since the relative contribution of preamplifier's input voltage and current noise is different depending on the dynamic resistance or flux-to-voltage transfer of the SQUID, the results showed that the total noise of a SQUID system at low-frequency range can be improved significantly by optimizing the preamplifier circuit parameters, mainly the collector current in case of low-noise bipolar transistor pairs.
We experimentally studied two important parameters of helium-cooled superconducting quantum interference devices (SQUIDs) in the voltage bias mode: the dynamic resistance Rd and the flux-to-current transfer coefficient ∂i/∂Φ, with different junction shunt resistors RJ. We investigated a voltage-biased SQUID using the direct readout current-to-voltage converter scheme involving an operational amplifier. At higher RJ, the flux-to-voltage conversion coefficient ∂V/∂Φ becomes sufficiently large to effectively suppress the room-temperature amplifier's noise without any need for additional feedback circuits. The McCumber parameter limits the rise of ∂V/∂Φ. We discuss the performance of voltage-biased SQUIDs at different effective McCumber parameters.
User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.