Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optics Express

Micro-fabricated vapor cells with sealed Rb atoms by distillation at wafer level and two-step bonding for miniature atomic clocks

Hitoshi Nishino, Yasubumi Furuya, Takahito Ono

Published Nov 25, 2021• 16 citations
Publisher

Abstract

This paper proposes a new method to fabricate and evaluate Rb vapor cells sealed by two-step bonding for miniature atomic clocks. The proposed method achieves miniaturization and long-term frequency stability by the wafer-level process. First, the vapor cells are fabricated to seal only Rb atoms in vacuum to confirm the absence of residual gases. Second, the vapor cell is fabricated to seal with buffer gases to confirm the stability. The Allan deviation at an averaging time of 3000 s is 1.7 × 10−11. These results show that the proposed method has improved long-term stability compared to the vapor cell fabricated by the conventional method that uses an alkali-atom dispenser.

DOI
10.1364/oe.442859

Related papers

Microfabricated Alkali Atom Vapor Cells for Chip Scale Atomic Clock

M.-Z. Huang, Jiashan Zhu, Guangfeng Shi +2 more

In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.

Annual Conference of the Chinese Society of Micro-Nano Technology (CSMNT)•Nov 22, 2017•0 citations

Microfabricated vapor cells filled with a cesium dispensing paste for miniature atomic clocks

Vincent N. Maurice, J. Rutkowski, Eric Kroemer +6 more

A method for filling alkali vapor cells with cesium from a dispensing paste is proposed and its compliance with miniature atomic clock applications is evaluated. The paste is an organic-inorganic composition of cesium molybdate, zirconium-aluminum powder, and a hybrid organic-inorganic binder. It is compatible with collective deposition processes such as micro-drop dispensing, which can be done under ambient atmosphere at the wafer-level. After deposition and sealing by anodic bonding, cesium is released from the consolidated paste through local heating with a high power laser. Linear absorption signals have been observed over one year in several cells, showing a stable atomic density. For further validation of this technology for clock applications, one cell has been implemented in a coherent population trapping clock setup to monitor its frequency stability. A fractional frequency aging rate around –4.4 × 10−12 per day has been observed, which is compliant with a clock frequency instability below 1 × 10−11 at one day integration time. This filling method can drastically reduce the cost and the complexity of alkali vapor cell fabrication.

Applied Physics Letters•Apr 17, 2017•42 citations

Reflection-type vapor cell for micro atomic clocks using local anodic bonding of 45° mirrors

Hitoshi Nishino, Yuichiro Yano, Motoaki Hara +4 more

This Letter reports the design, fabrication, and evaluation of reflection-type planar vapor cells for chip-scale atomic clocks. The cell with 2-8 mm cavity length contains two 45° Bragg reflector mirrors assembled using a local anodic bonding. Coherent population trapping resonance of Rb atoms is observed, realizing an atomic clock operation. Allan deviations at an averaging time of 1 s are ${2.2} \times {{1}}{{{0}}^{- 10}}$ and ${9.5} \times {{1}}{{{0}}^{- 11}}$ for 2 mm long and 6 mm long vapor cells, respectively. These results show that planar vapor cells compatible with a system-in-package are feasible without degradation of clock stabilities compared to conventional vertically stacked cells.

Optics Letters•Apr 15, 2021•18 citations

Micro-fabricated Alkali Vapor Cells for Chip Scale Atomic Clocks Sealed at Low Temperature with Thin-Film Metallic Bonding

Rahel Strässle, Matthieu Pellaton, Yves Pétremand +4 more

Micro-fabriced alkali vapor cells and applications in various fields as the heart of ultraprecise sensors, like chip scale atomic clocks, magnetometers or gyroscopes. Miniaturization asks for either new fabrication techniques or new physical concepts or both. We present here a new fabrication technique for the alkali cells which allows the integration of a anti-relaxation wall coating for alkali vapor cells in order to improve the signal for miniazurized cells.

•Jan 1, 2013•0 citations

Alkali metal-wax micropackets for chip-scale atomic clocks

S. Radhakrishnan, A. Lai

We report a novel methodology for fabrication of vapor cells for chip-scale atomic clocks (CSAC) using wafer-scale micromachining processes. Alkali metals are enclosed in a chemically inert wax to preform alkali metal-wax micropackets, keeping the alkali metals from reacting with the ambient during the vapor cell fabrication. Apart from the high level of purity of the alkali metals in the resulting vapor cells, this method holds promise for inexpensive and flexible manufacturing of vapor cells, as well as easy handling of alkali metals used for a variety of applications other than for CSAC. The optical absorption on fabricated rubidium-87 (Rb/sup 87/) vapor cells over the D2 transitions of Rb/sup 87/ shows a contrast of more than 65%, important to the frequency stability of CSAC.

International Conference on Solid-State Sensors, Actuators and Microsystems•Aug 24, 2005•29 citations

Wafer-scale fabrication of alkali vapor cells

Yang Li, Marlou R. Slot, Dongyu Sohn +3 more

This paper describes the progress made in developing wafer-scale fabrication process of alkali vapor cells for chip-scale atomic devices such as Coherent Population Trapping (CPT) clocks, optical frequency standards and Rydberg-atom-based sensors. The wafer level fabrication process uses anodic bonding and introduces alkali atoms by chemical reactions of Alkali Chloride with Barium Azide. This method is compatible to make cells with a wide range of buffer gas species and pressures, including evacuated cells. We improve the yield of the cells to above 50%. We will show the residual gas pressures for evacuated cells are mostly consistent with zero within the resolution of the saturation absorption spectroscopy measurement. The temperature coefficients for the CPT spectroscopy are improved with Ar-N2 mixture buffer gas compared with only N2 buffer gas.

Optical and Quantum Sensing and Precision Metrology II•Mar 19, 2025•0 citations
This paper proposes a new method to fabricate and evaluate Rb vapor cells sealed by two-step bonding for miniature atomic clocks. The proposed method achieves miniaturization and long-term frequency stability by the wafer-level process. First, the vapor cells are fabricated to seal only Rb atoms in vacuum to confirm the absence of residual gases. Second, the vapor cell is fabricated to seal with buffer gases to confirm the stability. The Allan deviation at an averaging time of 3000 s is 1.7 × 10−11. These results show that the proposed method has improved long-term stability compared to the vapor cell fabricated by the conventional method that uses an alkali-atom dispenser.
In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.
A method for filling alkali vapor cells with cesium from a dispensing paste is proposed and its compliance with miniature atomic clock applications is evaluated. The paste is an organic-inorganic composition of cesium molybdate, zirconium-aluminum powder, and a hybrid organic-inorganic binder. It is compatible with collective deposition processes such as micro-drop dispensing, which can be done under ambient atmosphere at the wafer-level. After deposition and sealing by anodic bonding, cesium is released from the consolidated paste through local heating with a high power laser. Linear absorption signals have been observed over one year in several cells, showing a stable atomic density. For further validation of this technology for clock applications, one cell has been implemented in a coherent population trapping clock setup to monitor its frequency stability. A fractional frequency aging rate around –4.4 × 10−12 per day has been observed, which is compliant with a clock frequency instability below 1 × 10−11 at one day integration time. This filling method can drastically reduce the cost and the complexity of alkali vapor cell fabrication.
This Letter reports the design, fabrication, and evaluation of reflection-type planar vapor cells for chip-scale atomic clocks. The cell with 2-8 mm cavity length contains two 45° Bragg reflector mirrors assembled using a local anodic bonding. Coherent population trapping resonance of Rb atoms is observed, realizing an atomic clock operation. Allan deviations at an averaging time of 1 s are 2.2×10−10{2.2} \times {{1}}{{{0}}^{- 10}}2.2×10−10 and 9.5×10−11{9.5} \times {{1}}{{{0}}^{- 11}}9.5×10−11 for 2 mm long and 6 mm long vapor cells, respectively. These results show that planar vapor cells compatible with a system-in-package are feasible without degradation of clock stabilities compared to conventional vertically stacked cells.
We report a novel methodology for fabrication of vapor cells for chip-scale atomic clocks (CSAC) using wafer-scale micromachining processes. Alkali metals are enclosed in a chemically inert wax to preform alkali metal-wax micropackets, keeping the alkali metals from reacting with the ambient during the vapor cell fabrication. Apart from the high level of purity of the alkali metals in the resulting vapor cells, this method holds promise for inexpensive and flexible manufacturing of vapor cells, as well as easy handling of alkali metals used for a variety of applications other than for CSAC. The optical absorption on fabricated rubidium-87 (Rb/sup 87/) vapor cells over the D2 transitions of Rb/sup 87/ shows a contrast of more than 65%, important to the frequency stability of CSAC.
This paper describes the progress made in developing wafer-scale fabrication process of alkali vapor cells for chip-scale atomic devices such as Coherent Population Trapping (CPT) clocks, optical frequency standards and Rydberg-atom-based sensors. The wafer level fabrication process uses anodic bonding and introduces alkali atoms by chemical reactions of Alkali Chloride with Barium Azide. This method is compatible to make cells with a wide range of buffer gas species and pressures, including evacuated cells. We improve the yield of the cells to above 50%. We will show the residual gas pressures for evacuated cells are mostly consistent with zero within the resolution of the saturation absorption spectroscopy measurement. The temperature coefficients for the CPT spectroscopy are improved with Ar-N2 mixture buffer gas compared with only N2 buffer gas.