Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optics Letters

Reflection-type vapor cell for micro atomic clocks using local anodic bonding of 45° mirrors

Hitoshi Nishino, Yuichiro Yano, Motoaki Hara, Masaya Toda, Masatoshi Kajita, T. Ido, Takahito Ono

Published Apr 15, 2021• 18 citations
Publisher

Abstract

This Letter reports the design, fabrication, and evaluation of reflection-type planar vapor cells for chip-scale atomic clocks. The cell with 2-8 mm cavity length contains two 45° Bragg reflector mirrors assembled using a local anodic bonding. Coherent population trapping resonance of Rb atoms is observed, realizing an atomic clock operation. Allan deviations at an averaging time of 1 s are ${2.2} \times {{1}}{{{0}}^{- 10}}$ and ${9.5} \times {{1}}{{{0}}^{- 11}}$ for 2 mm long and 6 mm long vapor cells, respectively. These results show that planar vapor cells compatible with a system-in-package are feasible without degradation of clock stabilities compared to conventional vertically stacked cells.

DOI
10.1364/ol.424354

Related papers

A Reflection Type Vapor Cell Based on Local Anodic Bonding of 45° Mirrors for Micro Atomic Clocks

Hitoshi Nishino, Masaya Toda, Yuichiro Yano +4 more

This paper reports the design, fabrication and evaluation of a reflection-type micro Rb vapor cell fabricated by local anodic bonding of small 45° mirrors. The 45° mirrors with a Bragg reflector are fabricated by using dicing process. The vapor cells having a horizontal cavity with the 45° mirrors at the both ends are fabricated by anodic bonding process. Optical absorption of Rb and CPT (Coherent Population Trapping) resonance for atomic clock operation are evaluated.

International Conference on Solid-State Sensors, Actuators and Microsystems•Jun 1, 2019•6 citations

A Reflection-Type Vapor Cell for Micro Atomic Clock

Hitoshi Nishino, Masaya Toda, Yoshiaki Kanamori +5 more

This paper reports the design, fabrication and evaluation of a reflection-type Rb vapor cell with a Glass/Si/Glass structure for chip-scale micro atomic clocks. To miniaturize the cell and obtain a Rb resonance signal with a high sensitivity, long laser light traveling pass on the horizontal plane is required in the vapor cell. The horizontal Rb vapor cell with integrated mirrors are proposed and developed. A (100)-oriented Si wafer with cut off 9.74° toward [011] direction was used to make 45° mirrors by using anisotropic wet etching. Also, 90° mirrors were fabricated by Si deep RIE (Reactive Ion Etching) and H2annealing. Absorption line of Rb was confirmed and CPT (Coherent Population Trapping) resonance was demonstrated in the fabricated devices.

IEEE International Conference on Micro Electro Mechanical Systems (MEMS)•Jan 1, 2019•1 citation

Micro Rb atomic vapor cells for the chip-scale atomic clock

Chang Zhang, Shuangyou Zhang, Guo Dengzhu +2 more

Nowadays, the portable atomic clocks with small size and low power consumption have attracted much attention. With the development of the coherent population trapping (CPT) and the micro-electro-mechanical systems (MEMS) technologies, it is possible to fabricate the miniature atomic clocks with power consumption less than 100mW. Researchers have already made great progress in the miniaturization of VCSELs, RF circuits, and photodiodes, which are the key technologies of the chip-scale atomic clock (CSAC). However, the fabrication of micro alkali atomic vapor cells is still to be improved. In this article, we describe the fabrication of micro Rb atomic vapor cells with inner dimensions of 3 mm length and 3 mm radius using anodic bonding and chemical reaction between BaN6and RbCl. The optical absorption and CPT resonances of the cells were measured slightly above the room temperature. In this condition, the consumption in the temperature control will be very low. Moreover, the long life (more than four years) of the cells makes it possible to use them in CSACs.

Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS)•May 1, 2014•4 citations

Stable85Rb micro vapour cells: fabrication based on anodic bonding and application in chip-scale atomic clocks

苏娟, Ke Deng, Deng-Zhu Guo +4 more

We describe the microfabrication of 85 Rb vapour cells using a glass-silicon anodic bonding technique and in situ chemical reaction between rubidium chloride and barium azide to produce Rb. Under controlled conditions, the pure metallic Rb drops and buffer gases were obtained in the cells with a few mm 3 internal volumes during the cell sealing process. At an ambient temperature of 90 °C the optical absorption resonance of 85 Rb D1 transition with proper broadening and the corresponding coherent population trapping (CPT) resonance, with a signal contrast of 1.5% and linewidth of about 1.7 kHz, have been detected. The sealing quality and the stability of the cells have also been demonstrated experimentally by using the helium leaking detection and the after-9-month optoelectronics measurement which shows a similar CPT signal as its original status. In addition, the physics package of chip-scale atomic clock (CSAC) based on the cell was realized. The measured frequency stability of the physics package can reach to 2.1 × 10 −10 at one second when the cell was heated to 100 °C which proved that the cell has the quality to be used in portable and battery-operated devices.

Chinese Physics B•Nov 1, 2010•14 citations

The Microfabricated Alkali Vapor Cell with High Hermeticity for Chip-Scale Atomic Clock

Shuo Jia, Zhiyuan Jiang, Binbin Jiao +4 more

Herein, a microfabricated millimeter-level vapor alkali cell with a high hermeticity is fabricated through a wet etching and single-chip anodic bonding process. The vapor cell, containing Rb and N2, was investigated in a coherent population trapping (CPT) setup for the application of a chip-scale atomic clock (CSAC). The contrast of CPT resonance is up to 1.1% within the only 1 mm length of light interacting with atom. The effects of some critical external parameters on the CPT resonance, such as laser intensity, cell temperature, and buffer gas pressure, are thoroughly studied and optimized. The improved microfabricated vapor cell also exhibited great potential for other chip-scale atomic devices.

Applied Sciences•Jan 3, 2022•21 citations

Micromachined alkali atom vapor cells for chip-scale atomic clocks

Li‐Anne Liew, Svenja A. Knappe, John Moreland +3 more

This paper describes the fabrication of chip-scale alkali atom vapor cells, for use in highly miniaturized atomic frequency references, using silicon micromachining and anodic bonding technology. The cells consist of silicon cavities with internal volume ranging from a few mm/sup 3/ to less than 1 mm/sup 3/. The cells were filled with cesium and nitrogen buffer gas either by chemical reaction of cesium chloride and barium azide, or by direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption spectra were obtained from the cells, and coherent population trapping resonances with linewidths of about 1 kHz were measured.

IEEE International Conference on Micro Electro Mechanical Systems (MEMS)•Aug 2, 2004•15 citations
This Letter reports the design, fabrication, and evaluation of reflection-type planar vapor cells for chip-scale atomic clocks. The cell with 2-8 mm cavity length contains two 45° Bragg reflector mirrors assembled using a local anodic bonding. Coherent population trapping resonance of Rb atoms is observed, realizing an atomic clock operation. Allan deviations at an averaging time of 1 s are 2.2×10−10{2.2} \times {{1}}{{{0}}^{- 10}}2.2×10−10 and 9.5×10−11{9.5} \times {{1}}{{{0}}^{- 11}}9.5×10−11 for 2 mm long and 6 mm long vapor cells, respectively. These results show that planar vapor cells compatible with a system-in-package are feasible without degradation of clock stabilities compared to conventional vertically stacked cells.
This paper reports the design, fabrication and evaluation of a reflection-type Rb vapor cell with a Glass/Si/Glass structure for chip-scale micro atomic clocks. To miniaturize the cell and obtain a Rb resonance signal with a high sensitivity, long laser light traveling pass on the horizontal plane is required in the vapor cell. The horizontal Rb vapor cell with integrated mirrors are proposed and developed. A (100)-oriented Si wafer with cut off 9.74° toward [011] direction was used to make 45° mirrors by using anisotropic wet etching. Also, 90° mirrors were fabricated by Si deep RIE (Reactive Ion Etching) and H2annealing. Absorption line of Rb was confirmed and CPT (Coherent Population Trapping) resonance was demonstrated in the fabricated devices.
Nowadays, the portable atomic clocks with small size and low power consumption have attracted much attention. With the development of the coherent population trapping (CPT) and the micro-electro-mechanical systems (MEMS) technologies, it is possible to fabricate the miniature atomic clocks with power consumption less than 100mW. Researchers have already made great progress in the miniaturization of VCSELs, RF circuits, and photodiodes, which are the key technologies of the chip-scale atomic clock (CSAC). However, the fabrication of micro alkali atomic vapor cells is still to be improved. In this article, we describe the fabrication of micro Rb atomic vapor cells with inner dimensions of 3 mm length and 3 mm radius using anodic bonding and chemical reaction between BaN6and RbCl. The optical absorption and CPT resonances of the cells were measured slightly above the room temperature. In this condition, the consumption in the temperature control will be very low. Moreover, the long life (more than four years) of the cells makes it possible to use them in CSACs.
We describe the microfabrication of 85 Rb vapour cells using a glass-silicon anodic bonding technique and in situ chemical reaction between rubidium chloride and barium azide to produce Rb. Under controlled conditions, the pure metallic Rb drops and buffer gases were obtained in the cells with a few mm 3 internal volumes during the cell sealing process. At an ambient temperature of 90 °C the optical absorption resonance of 85 Rb D1 transition with proper broadening and the corresponding coherent population trapping (CPT) resonance, with a signal contrast of 1.5% and linewidth of about 1.7 kHz, have been detected. The sealing quality and the stability of the cells have also been demonstrated experimentally by using the helium leaking detection and the after-9-month optoelectronics measurement which shows a similar CPT signal as its original status. In addition, the physics package of chip-scale atomic clock (CSAC) based on the cell was realized. The measured frequency stability of the physics package can reach to 2.1 × 10 −10 at one second when the cell was heated to 100 °C which proved that the cell has the quality to be used in portable and battery-operated devices.
Herein, a microfabricated millimeter-level vapor alkali cell with a high hermeticity is fabricated through a wet etching and single-chip anodic bonding process. The vapor cell, containing Rb and N2, was investigated in a coherent population trapping (CPT) setup for the application of a chip-scale atomic clock (CSAC). The contrast of CPT resonance is up to 1.1% within the only 1 mm length of light interacting with atom. The effects of some critical external parameters on the CPT resonance, such as laser intensity, cell temperature, and buffer gas pressure, are thoroughly studied and optimized. The improved microfabricated vapor cell also exhibited great potential for other chip-scale atomic devices.
This paper describes the fabrication of chip-scale alkali atom vapor cells, for use in highly miniaturized atomic frequency references, using silicon micromachining and anodic bonding technology. The cells consist of silicon cavities with internal volume ranging from a few mm/sup 3/ to less than 1 mm/sup 3/. The cells were filled with cesium and nitrogen buffer gas either by chemical reaction of cesium chloride and barium azide, or by direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption spectra were obtained from the cells, and coherent population trapping resonances with linewidths of about 1 kHz were measured.