Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optical and Quantum Sensing and Precision Metrology II

Wafer-scale fabrication of alkali vapor cells

Yang Li, Marlou R. Slot, Dongyu Sohn, Susan A. Schima, Matthew T. Hummon, John E. Kitching

Published Mar 19, 2025• 0 citations
Publisher

Abstract

This paper describes the progress made in developing wafer-scale fabrication process of alkali vapor cells for chip-scale atomic devices such as Coherent Population Trapping (CPT) clocks, optical frequency standards and Rydberg-atom-based sensors. The wafer level fabrication process uses anodic bonding and introduces alkali atoms by chemical reactions of Alkali Chloride with Barium Azide. This method is compatible to make cells with a wide range of buffer gas species and pressures, including evacuated cells. We improve the yield of the cells to above 50%. We will show the residual gas pressures for evacuated cells are mostly consistent with zero within the resolution of the saturation absorption spectroscopy measurement. The temperature coefficients for the CPT spectroscopy are improved with Ar-N2 mixture buffer gas compared with only N2 buffer gas.

DOI
10.1117/12.3039945

Related papers

Micromachined alkali atom vapor cells for chip-scale atomic clocks

Li‐Anne Liew, Svenja A. Knappe, John Moreland +3 more

This paper describes the fabrication of chip-scale alkali atom vapor cells, for use in highly miniaturized atomic frequency references, using silicon micromachining and anodic bonding technology. The cells consist of silicon cavities with internal volume ranging from a few mm/sup 3/ to less than 1 mm/sup 3/. The cells were filled with cesium and nitrogen buffer gas either by chemical reaction of cesium chloride and barium azide, or by direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption spectra were obtained from the cells, and coherent population trapping resonances with linewidths of about 1 kHz were measured.

IEEE International Conference on Micro Electro Mechanical Systems (MEMS)•Aug 2, 2004•15 citations

Wafer-scale fabrication of evacuated alkali vapor cells

Yang Li, Donggyu B. Sohn, Matthew T. Hummon +2 more

We describe a process for fabricating a wafer-scale array of alkali metal vapor cells with low residual gas pressure. We show that by etching long, thin channels between the cells on the Si wafer surface, the residual gas pressure in the evacuated vapor cell can be reduced to below 0.5 kPa (4 Torr) with a yield above 50%. The low residual gas pressure in these mass-producible alkali vapor cells can enable a new generation of low-cost chip-scale atomic devices such as vapor cell optical clocks, wavelength references, and Rydberg sensors.

arXiv:2405.11088•Optics Letters•Aug 14, 2024•12 citations

The Microfabricated Alkali Vapor Cell with High Hermeticity for Chip-Scale Atomic Clock

Shuo Jia, Zhiyuan Jiang, Binbin Jiao +4 more

Herein, a microfabricated millimeter-level vapor alkali cell with a high hermeticity is fabricated through a wet etching and single-chip anodic bonding process. The vapor cell, containing Rb and N2, was investigated in a coherent population trapping (CPT) setup for the application of a chip-scale atomic clock (CSAC). The contrast of CPT resonance is up to 1.1% within the only 1 mm length of light interacting with atom. The effects of some critical external parameters on the CPT resonance, such as laser intensity, cell temperature, and buffer gas pressure, are thoroughly studied and optimized. The improved microfabricated vapor cell also exhibited great potential for other chip-scale atomic devices.

Applied Sciences•Jan 3, 2022•21 citations

Microfabricated alkali atom vapor cells

Li‐Anne Liew, Svenja A. Knappe, John Moreland +3 more

We describe the fabrication of chip-sized alkali atom vapor cells using silicon micromachining and anodic bonding technology. Such cells may find use in highly miniaturized atomic frequency references or magnetometers. The cells consist of cavities etched in silicon, with internal volumes as small as 1 mm3. Two techniques for introducing cesium and a buffer gas into the cells are described: one based on chemical reaction between cesium chloride and barium azide, and the other based on direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption and coherent population trapping resonances were measured in the cells.

Applied Physics Letters•Apr 1, 2004•377 citations

Wafer-scale fabrication of temperature-compensated alkali vapor cells

Yang Li, Marlou R. Slot, Matthew T. Hummon +2 more

We demonstrate wafer-scale fabrication of temperature-compensated alkali vapor cells using a mixture of Ar and N2 buffer gases. The temperature coefficient of the fractional frequency shift of the hyperfine clock resonance is reduced from a typical value of ≈30×10−9/ K for cells containing pure N2 to below ≈3×10−9/ K for the buffer gas mixture. This result is an important step toward the mass production of temperature-compensated atomic vapor cell-based devices such as chip-scale atomic clocks.

Applied Physics Letters•Jun 2, 2025•10 citations

Microfabricated Alkali Atom Vapor Cells for Chip Scale Atomic Clock

M.-Z. Huang, Jiashan Zhu, Guangfeng Shi +2 more

In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.

Annual Conference of the Chinese Society of Micro-Nano Technology (CSMNT)•Nov 22, 2017•0 citations
This paper describes the progress made in developing wafer-scale fabrication process of alkali vapor cells for chip-scale atomic devices such as Coherent Population Trapping (CPT) clocks, optical frequency standards and Rydberg-atom-based sensors. The wafer level fabrication process uses anodic bonding and introduces alkali atoms by chemical reactions of Alkali Chloride with Barium Azide. This method is compatible to make cells with a wide range of buffer gas species and pressures, including evacuated cells. We improve the yield of the cells to above 50%. We will show the residual gas pressures for evacuated cells are mostly consistent with zero within the resolution of the saturation absorption spectroscopy measurement. The temperature coefficients for the CPT spectroscopy are improved with Ar-N2 mixture buffer gas compared with only N2 buffer gas.
This paper describes the fabrication of chip-scale alkali atom vapor cells, for use in highly miniaturized atomic frequency references, using silicon micromachining and anodic bonding technology. The cells consist of silicon cavities with internal volume ranging from a few mm/sup 3/ to less than 1 mm/sup 3/. The cells were filled with cesium and nitrogen buffer gas either by chemical reaction of cesium chloride and barium azide, or by direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption spectra were obtained from the cells, and coherent population trapping resonances with linewidths of about 1 kHz were measured.
We describe a process for fabricating a wafer-scale array of alkali metal vapor cells with low residual gas pressure. We show that by etching long, thin channels between the cells on the Si wafer surface, the residual gas pressure in the evacuated vapor cell can be reduced to below 0.5 kPa (4 Torr) with a yield above 50%. The low residual gas pressure in these mass-producible alkali vapor cells can enable a new generation of low-cost chip-scale atomic devices such as vapor cell optical clocks, wavelength references, and Rydberg sensors.
Herein, a microfabricated millimeter-level vapor alkali cell with a high hermeticity is fabricated through a wet etching and single-chip anodic bonding process. The vapor cell, containing Rb and N2, was investigated in a coherent population trapping (CPT) setup for the application of a chip-scale atomic clock (CSAC). The contrast of CPT resonance is up to 1.1% within the only 1 mm length of light interacting with atom. The effects of some critical external parameters on the CPT resonance, such as laser intensity, cell temperature, and buffer gas pressure, are thoroughly studied and optimized. The improved microfabricated vapor cell also exhibited great potential for other chip-scale atomic devices.
We describe the fabrication of chip-sized alkali atom vapor cells using silicon micromachining and anodic bonding technology. Such cells may find use in highly miniaturized atomic frequency references or magnetometers. The cells consist of cavities etched in silicon, with internal volumes as small as 1 mm3. Two techniques for introducing cesium and a buffer gas into the cells are described: one based on chemical reaction between cesium chloride and barium azide, and the other based on direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption and coherent population trapping resonances were measured in the cells.
We demonstrate wafer-scale fabrication of temperature-compensated alkali vapor cells using a mixture of Ar and N2 buffer gases. The temperature coefficient of the fractional frequency shift of the hyperfine clock resonance is reduced from a typical value of ≈30×10−9/ K for cells containing pure N2 to below ≈3×10−9/ K for the buffer gas mixture. This result is an important step toward the mass production of temperature-compensated atomic vapor cell-based devices such as chip-scale atomic clocks.
In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.