Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Topical Meeting on Photonic Switching

Operating Curves for Optical Bistable Devices

P. Wheatley, John Edwin Midwinter

Published Jan 1, 1987• 0 citations
Publisher

Abstract

There is much interest in the use of optical bistable devices as logic gates for optical processors. Although desirable properties have been reported, it is difficult to see how these are offset by less desirable ones. All properties of the device can be controlled to a certain extent, principally by the bias conditions. Here we show how steady state and dynamic responses vary simultaneously with these parameters. These operating curves can be used to see the capabilities of a device or to choose the optimum bias conditions.

DOI
10.1364/phs.1987.fb5

Related papers

Operating curves for optical bistable devices

P. Wheatley, John Edwin Midwinter

A graphical method is described where-by the important steady state and dynamic responses of an optical bistable device can be viewed simultaneously. This results in a set of ‘operating curves’ which indicate how well an optical bistable device satisfies the requirements to perform a particular logic function. The operating curves may be used to find the optimum conditions to perform a function and they also show how resilient this point is in the presence of fluctuations in operating conditions.

IEE Proceedings J Optoelectronics•Jan 1, 1987•6 citations

Steady Characteristics of A Biased Optically Bistable Device

Ch. Golaire, Paul Mandel, P. Laws

We consider an optically bistable device illuminated by two incident beams: a biasing (or holding) beam which brings the system into a state appropriate to perform a given logic operation and a controlling (or address) beam. The refraction index is n=n0+n21I1c+n22I2c where Ikc is the cavity intensity of the beam k.

Topical Meeting on Optical Bistability (OB)•Jan 1, 1985•0 citations

OPTICAL FLIP-FLOP AND LOGIC GATE OPERATIONS WITH ZnSe NONLINEAR ETALONS USING TWO LIGHT BEAMS

Takashi Kurokawa, Hiroyuki Tsuda, S. Fukushima

There has recently been increasing interest in bistable optical devices because of their potential for all-optical signal processing in optical computing systems and optical transmission networks(1), (2). Nonlinear Fabry-Perot etalons whose steady-state properties have been studied extensively are one candidate for such applications. Relatively little work, however, has been done on their operating characteristics and transient behavior(3).

•Jul 18, 1988•0 citations

Cascadable Digital Optical Logic Circuit Elements in the Visible and Infrared: Prospects for Fast Array Processors

Stuart D. Smith, Andy C. Walker, B. S. Wherrett

An extensive experimental and theoretical programme in our laboratory and in conjunction with a number of other European laboratories has now developed a series of optical circuit elements including optically bistable switches capable of steady state cw (operation) combined with external address for both visible and infrared wavelengths. The devices are sufficiently controllable that the characteristics may be varied to give bistable switches, bistable memories, latchable gates, resettable gates or analogue amplifying elements or transphasors.

•Jan 1, 1985•0 citations

Graphical analysis of dynamic response of optical bistable devices

P. Wheatley, John Edwin Midwinter

We present a simple graphical analysis of the dynamic response of optical bistable devices. This technique shows qualitatively how the switching time of a device is affected by optical bias and signal powers and initial bias voltage, and may be used to optimise the switching time of a device.

Electronics Letters•Oct 9, 1986•2 citations

Introduction To Bistable Optical Devices For Optical Signal Processing

E. Garmire

This paper addresses the concept of active optical processing, in which signals are processed due to a nonlinear transfer function (light output as a function of light input). The particular active device considered here is a bistable optical device (BOD), which typically has transfer curves such as those shown in Fig. 1. Devices whici have transfer functions such as these can be used fc,-- signal enhancement, optical logic, memories, and switching. The aim of developing active optical processing is to achieve high speed all-optical operation, which is not limited by electron transit time considerations. An all-optical processor should have psec response times. In addition, the all-optical nature means freedom from emi, rfi, cross-talk and security, which are also characteristics of optical fibers.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 25, 1980•3 citations
There is much interest in the use of optical bistable devices as logic gates for optical processors. Although desirable properties have been reported, it is difficult to see how these are offset by less desirable ones. All properties of the device can be controlled to a certain extent, principally by the bias conditions. Here we show how steady state and dynamic responses vary simultaneously with these parameters. These operating curves can be used to see the capabilities of a device or to choose the optimum bias conditions.
A graphical method is described where-by the important steady state and dynamic responses of an optical bistable device can be viewed simultaneously. This results in a set of ‘operating curves’ which indicate how well an optical bistable device satisfies the requirements to perform a particular logic function. The operating curves may be used to find the optimum conditions to perform a function and they also show how resilient this point is in the presence of fluctuations in operating conditions.
An extensive experimental and theoretical programme in our laboratory and in conjunction with a number of other European laboratories has now developed a series of optical circuit elements including optically bistable switches capable of steady state cw (operation) combined with external address for both visible and infrared wavelengths. The devices are sufficiently controllable that the characteristics may be varied to give bistable switches, bistable memories, latchable gates, resettable gates or analogue amplifying elements or transphasors.
This paper addresses the concept of active optical processing, in which signals are processed due to a nonlinear transfer function (light output as a function of light input). The particular active device considered here is a bistable optical device (BOD), which typically has transfer curves such as those shown in Fig. 1. Devices whici have transfer functions such as these can be used fc,-- signal enhancement, optical logic, memories, and switching. The aim of developing active optical processing is to achieve high speed all-optical operation, which is not limited by electron transit time considerations. An all-optical processor should have psec response times. In addition, the all-optical nature means freedom from emi, rfi, cross-talk and security, which are also characteristics of optical fibers.