Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEE Proceedings J Optoelectronics

Operating curves for optical bistable devices

P. Wheatley, John Edwin Midwinter

Published Jan 1, 1987• 6 citations
Publisher

Abstract

A graphical method is described where-by the important steady state and dynamic responses of an optical bistable device can be viewed simultaneously. This results in a set of ‘operating curves’ which indicate how well an optical bistable device satisfies the requirements to perform a particular logic function. The operating curves may be used to find the optimum conditions to perform a function and they also show how resilient this point is in the presence of fluctuations in operating conditions.

DOI
10.1049/ip-j.1987.0056

Related papers

Operating Curves for Optical Bistable Devices

P. Wheatley, John Edwin Midwinter

There is much interest in the use of optical bistable devices as logic gates for optical processors. Although desirable properties have been reported, it is difficult to see how these are offset by less desirable ones. All properties of the device can be controlled to a certain extent, principally by the bias conditions. Here we show how steady state and dynamic responses vary simultaneously with these parameters. These operating curves can be used to see the capabilities of a device or to choose the optimum bias conditions.

Topical Meeting on Photonic Switching•Jan 1, 1987•0 citations

Optical Bistability

Guang S. He

When the output parameter of an optical device could be a multivalued function of the input parameter, this device can be working in an optical bistable status. The most typical optical bistable device is a Fabry–Perot cavity containing a nonlinear optical medium, the refractive index of which depends on the light intensity. Upon the action of an intense input optical beam, the transmitted (or reflected) intensity of this device may exhibit a nonlinear response to the incident light intensity variation and, especially under appropriate working conditions, the characteristic output/input curve may manifest a single (or multiple) hysteresis loop(s). Such type of optical bistable device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element, depending on the chosen nonlinear medium and operation conditions.

Oxford University Press eBooks•Oct 30, 2014•1 citation

Graphical analysis of dynamic response of optical bistable devices

P. Wheatley, John Edwin Midwinter

We present a simple graphical analysis of the dynamic response of optical bistable devices. This technique shows qualitatively how the switching time of a device is affected by optical bias and signal powers and initial bias voltage, and may be used to optimise the switching time of a device.

Electronics Letters•Oct 9, 1986•2 citations

Introduction To Bistable Optical Devices For Optical Signal Processing

E. Garmire

This paper addresses the concept of active optical processing, in which signals are processed due to a nonlinear transfer function (light output as a function of light input). The particular active device considered here is a bistable optical device (BOD), which typically has transfer curves such as those shown in Fig. 1. Devices whici have transfer functions such as these can be used fc,-- signal enhancement, optical logic, memories, and switching. The aim of developing active optical processing is to achieve high speed all-optical operation, which is not limited by electron transit time considerations. An all-optical processor should have psec response times. In addition, the all-optical nature means freedom from emi, rfi, cross-talk and security, which are also characteristics of optical fibers.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 25, 1980•3 citations

Optical Bistability

The study of optical bistability and bistable devices is a special topic of nonlinear optics. In this chapter, we focus our discussion only on the most typical optical bistable configuration, i.e. a Fubry–Perot (F–P) etalon containing a nonlinear optical medium, the refractive-index of which depends on the light intensity. Under the action of an intense coherent optical beam, this device may exhibit a nonlinear response to the incident beam in the sense that the transmitted intensity is a nonlinear function of the incident intensity. Based on such a nonlinear response this type of device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element depending on the chosen nonlinear medium and operation conditions.

WORLD SCIENTIFIC eBooks•Dec 14, 2017•0 citations

Steady Characteristics of A Biased Optically Bistable Device

Ch. Golaire, Paul Mandel, P. Laws

We consider an optically bistable device illuminated by two incident beams: a biasing (or holding) beam which brings the system into a state appropriate to perform a given logic operation and a controlling (or address) beam. The refraction index is n=n0+n21I1c+n22I2c where Ikc is the cavity intensity of the beam k.

Topical Meeting on Optical Bistability (OB)•Jan 1, 1985•0 citations
A graphical method is described where-by the important steady state and dynamic responses of an optical bistable device can be viewed simultaneously. This results in a set of ‘operating curves’ which indicate how well an optical bistable device satisfies the requirements to perform a particular logic function. The operating curves may be used to find the optimum conditions to perform a function and they also show how resilient this point is in the presence of fluctuations in operating conditions.
There is much interest in the use of optical bistable devices as logic gates for optical processors. Although desirable properties have been reported, it is difficult to see how these are offset by less desirable ones. All properties of the device can be controlled to a certain extent, principally by the bias conditions. Here we show how steady state and dynamic responses vary simultaneously with these parameters. These operating curves can be used to see the capabilities of a device or to choose the optimum bias conditions.
When the output parameter of an optical device could be a multivalued function of the input parameter, this device can be working in an optical bistable status. The most typical optical bistable device is a Fabry–Perot cavity containing a nonlinear optical medium, the refractive index of which depends on the light intensity. Upon the action of an intense input optical beam, the transmitted (or reflected) intensity of this device may exhibit a nonlinear response to the incident light intensity variation and, especially under appropriate working conditions, the characteristic output/input curve may manifest a single (or multiple) hysteresis loop(s). Such type of optical bistable device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element, depending on the chosen nonlinear medium and operation conditions.
This paper addresses the concept of active optical processing, in which signals are processed due to a nonlinear transfer function (light output as a function of light input). The particular active device considered here is a bistable optical device (BOD), which typically has transfer curves such as those shown in Fig. 1. Devices whici have transfer functions such as these can be used fc,-- signal enhancement, optical logic, memories, and switching. The aim of developing active optical processing is to achieve high speed all-optical operation, which is not limited by electron transit time considerations. An all-optical processor should have psec response times. In addition, the all-optical nature means freedom from emi, rfi, cross-talk and security, which are also characteristics of optical fibers.
The study of optical bistability and bistable devices is a special topic of nonlinear optics. In this chapter, we focus our discussion only on the most typical optical bistable configuration, i.e. a Fubry–Perot (F–P) etalon containing a nonlinear optical medium, the refractive-index of which depends on the light intensity. Under the action of an intense coherent optical beam, this device may exhibit a nonlinear response to the incident beam in the sense that the transmitted intensity is a nonlinear function of the incident intensity. Based on such a nonlinear response this type of device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element depending on the chosen nonlinear medium and operation conditions.