Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Topical Meeting on Optical Bistability (OB)

Steady Characteristics of A Biased Optically Bistable Device

Ch. Golaire, Paul Mandel, P. Laws

Published Jan 1, 1985• 0 citations
Publisher

Abstract

We consider an optically bistable device illuminated by two incident beams: a biasing (or holding) beam which brings the system into a state appropriate to perform a given logic operation and a controlling (or address) beam. The refraction index is n=n0+n21I1c+n22I2c where Ikc is the cavity intensity of the beam k.
DOI
10.1364/obi.1985.md25

Related papers

Optimum Control Beam Angle for a Biased Fabry-Perot Bistable Device

Rosie Cush, Ian Bennion C

The use of bistable Fabry-Perot devices as multi-port cascadable devices has been frequently discussed in the literature (1-3). It has been envisaged that such devices could be addressed by a number of bias and control beams each approaching the device at a different angle (fig. 1). However, if these devices are to be cascadable, the same wavelength of light must be used for all control and bias beams. In this situation the control beam intensities inside the devices will be determined by the amplification effects of the cavity. Their behaviour will differ from that of the bias beam as the different incident angles produce additional phase changes. It has been shown that these additional phase changes give rise to bistable switching as the incident angle of the beam is changed (4) and this behaviour is demonstrated experimentally.

•Jan 1, 1987•0 citations

Optical Bistability

Guang S. He

When the output parameter of an optical device could be a multivalued function of the input parameter, this device can be working in an optical bistable status. The most typical optical bistable device is a Fabry–Perot cavity containing a nonlinear optical medium, the refractive index of which depends on the light intensity. Upon the action of an intense input optical beam, the transmitted (or reflected) intensity of this device may exhibit a nonlinear response to the incident light intensity variation and, especially under appropriate working conditions, the characteristic output/input curve may manifest a single (or multiple) hysteresis loop(s). Such type of optical bistable device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element, depending on the chosen nonlinear medium and operation conditions.

Oxford University Press eBooks•Oct 30, 2014•1 citation

Optimum control beam angle for a biased optical bistable device

Rosie Cush

The control beam intensity required to switch a multibeam, cascadable Fabry–Perot bistable device may be minimised by varying the beam incident angle.

Electronics Letters•Jun 4, 1987•2 citations

Optical Bistability

The study of optical bistability and bistable devices is a special topic of nonlinear optics. In this chapter, we focus our discussion only on the most typical optical bistable configuration, i.e. a Fubry–Perot (F–P) etalon containing a nonlinear optical medium, the refractive-index of which depends on the light intensity. Under the action of an intense coherent optical beam, this device may exhibit a nonlinear response to the incident beam in the sense that the transmitted intensity is a nonlinear function of the incident intensity. Based on such a nonlinear response this type of device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element depending on the chosen nonlinear medium and operation conditions.

WORLD SCIENTIFIC eBooks•Dec 14, 2017•0 citations

Measurement of the nonlinear refractive index in a bistable laser diode

Riccardo Calvani, Renato Caponi

The optical bistability (OB) behavior of a semiconductor Fabry-Perot (F.P.) cavity, biased around threshold, has been employed to evaluate the optical device parameters.1 In the present work, this approach was experimentally applied to measurements of the nonlinear refractive-index coefficient n2 in OB operating conditions.

Annual Meeting Optical Society of America•Jan 1, 1988•0 citations

Operating Curves for Optical Bistable Devices

P. Wheatley, John Edwin Midwinter

There is much interest in the use of optical bistable devices as logic gates for optical processors. Although desirable properties have been reported, it is difficult to see how these are offset by less desirable ones. All properties of the device can be controlled to a certain extent, principally by the bias conditions. Here we show how steady state and dynamic responses vary simultaneously with these parameters. These operating curves can be used to see the capabilities of a device or to choose the optimum bias conditions.

Topical Meeting on Photonic Switching•Jan 1, 1987•0 citations
The use of bistable Fabry-Perot devices as multi-port cascadable devices has been frequently discussed in the literature (1-3). It has been envisaged that such devices could be addressed by a number of bias and control beams each approaching the device at a different angle (fig. 1). However, if these devices are to be cascadable, the same wavelength of light must be used for all control and bias beams. In this situation the control beam intensities inside the devices will be determined by the amplification effects of the cavity. Their behaviour will differ from that of the bias beam as the different incident angles produce additional phase changes. It has been shown that these additional phase changes give rise to bistable switching as the incident angle of the beam is changed (4) and this behaviour is demonstrated experimentally.
When the output parameter of an optical device could be a multivalued function of the input parameter, this device can be working in an optical bistable status. The most typical optical bistable device is a Fabry–Perot cavity containing a nonlinear optical medium, the refractive index of which depends on the light intensity. Upon the action of an intense input optical beam, the transmitted (or reflected) intensity of this device may exhibit a nonlinear response to the incident light intensity variation and, especially under appropriate working conditions, the characteristic output/input curve may manifest a single (or multiple) hysteresis loop(s). Such type of optical bistable device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element, depending on the chosen nonlinear medium and operation conditions.
The study of optical bistability and bistable devices is a special topic of nonlinear optics. In this chapter, we focus our discussion only on the most typical optical bistable configuration, i.e. a Fubry–Perot (F–P) etalon containing a nonlinear optical medium, the refractive-index of which depends on the light intensity. Under the action of an intense coherent optical beam, this device may exhibit a nonlinear response to the incident beam in the sense that the transmitted intensity is a nonlinear function of the incident intensity. Based on such a nonlinear response this type of device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element depending on the chosen nonlinear medium and operation conditions.
There is much interest in the use of optical bistable devices as logic gates for optical processors. Although desirable properties have been reported, it is difficult to see how these are offset by less desirable ones. All properties of the device can be controlled to a certain extent, principally by the bias conditions. Here we show how steady state and dynamic responses vary simultaneously with these parameters. These operating curves can be used to see the capabilities of a device or to choose the optimum bias conditions.