With operating frequencies reaching hundreds of gigahertz and switching energies in the attojoule range, superconducting electronics has become one of the leading candidates among beyond CMOS technologies. The practical implementation of large scale superconducting digital systems is constrained by multiple challenges, including limited power delivery efficiency, restricted scalability and integration density, and the absence of mature electronic design automation tools for large scale circuit design. In this dissertation, modeling, analysis, and design methodologies are presented that address the scalability and integration density challenges of superconducting digital technologies. A methodology for thermal analysis is introduced to describe heat generation and propagation in rapid single flux quantum (RSFQ) circuits. The modeling approach provides temperature estimates that agree with numerical simulations while maintaining low computational cost, enabling temperature-aware design of RSFQ circuit structures and large scale layouts. By quantifying thermal effects on chip, this method supports reliable operation of digital circuits and guides the scaling of integration density in superconducting systems. To further improve scalability of superconducting digital circuits, the use of Josephson junctions with ferromagnetic barriers is investigated. Replacing the insulating barrier with a ferromagnetic layer modifies the current–phase relationship, enabling π-, 2ϕ-, and ϕ-junction operation. These junctions allow inductorless flux quantum storage, intrinsic bias, and phase logic, offering new approaches for area efficient and energy efficient computing with superconducting devices. An inductorless dynamic logic family based on bistable 2ϕ-junctions is proposed, exhibiting improved scalability compared with conventional RSFQ circuits. To enable accurate circuit analysis, a compact Verilog-A model of 2ϕ-junctions is developed. The model reproduces experimentally observed behavior of junctions with weak ferromagnetic and ferromagnetic insulator barriers, and simulations reveal the influence of harmonic components on switching dynamics, margins, and circuit robustness. A variation-aware design methodology is introduced for circuits employing superconductor-erromagnet-superconductor π-junctions. Sensitivities of the critical current density to process and temperature variations are quantified and margins are established for reliable circuit operation. It is shown that magnetic scattering, in particular spin-flip scattering, is the dominant source of parameter sensitivity in junctions with weak ferromagnetic barriers. Material and fabrication choices that enable better control of this parameter are therefore critical for improving reproducibility and reliable device performance. Together, the modeling and design methodologies developed in this dissertation contribute to improving the scalability and reliability of superconducting digital systems, supporting the advancement of high speed, energy efficient computing technologies.
With operating frequencies reaching hundreds of gigahertz and switching energies in the attojoule range, superconducting electronics has become one of the leading candidates among beyond CMOS technologies. The practical implementation of large scale superconducting digital systems is constrained by multiple challenges, including limited power delivery efficiency, restricted scalability and integration density, and the absence of mature electronic design automation tools for large scale circuit design. In this dissertation, modeling, analysis, and design methodologies are presented that address the scalability and integration density challenges of superconducting digital technologies. A methodology for thermal analysis is introduced to describe heat generation and propagation in rapid single flux quantum (RSFQ) circuits. The modeling approach provides temperature estimates that agree with numerical simulations while maintaining low computational cost, enabling temperature-aware design of RSFQ circuit structures and large scale layouts. By quantifying thermal effects on chip, this method supports reliable operation of digital circuits and guides the scaling of integration density in superconducting systems. To further improve scalability of superconducting digital circuits, the use of Josephson junctions with ferromagnetic barriers is investigated. Replacing the insulating barrier with a ferromagnetic layer modifies the current–phase relationship, enabling π-, 2ϕ-, and ϕ-junction operation. These junctions allow inductorless flux quantum storage, intrinsic bias, and phase logic, offering new approaches for area efficient and energy efficient computing with superconducting devices. An inductorless dynamic logic family based on bistable 2ϕ-junctions is proposed, exhibiting improved scalability compared with conventional RSFQ circuits. To enable accurate circuit analysis, a compact Verilog-A model of 2ϕ-junctions is developed. The model reproduces experimentally observed behavior of junctions with weak ferromagnetic and ferromagnetic insulator barriers, and simulations reveal the influence of harmonic components on switching dynamics, margins, and circuit robustness. A variation-aware design methodology is introduced for circuits employing superconductor-erromagnet-superconductor π-junctions. Sensitivities of the critical current density to process and temperature variations are quantified and margins are established for reliable circuit operation. It is shown that magnetic scattering, in particular spin-flip scattering, is the dominant source of parameter sensitivity in junctions with weak ferromagnetic barriers. Material and fabrication choices that enable better control of this parameter are therefore critical for improving reproducibility and reliable device performance. Together, the modeling and design methodologies developed in this dissertation contribute to improving the scalability and reliability of superconducting digital systems, supporting the advancement of high speed, energy efficient computing technologies.
Design Guidelines for Superconducting Digital Circuits Employing π-JJs With Ferromagnetic Barriers
π-Josephson junctions based on ferromagnetic barriers enable energy- and area-efficient superconducting digital circuits. The critical current densityJcof superconductor–ferromagnet–superconductor (SFS) junctions is highly sensitive to barrier thickness, magnetic scattering, and temperature, making reliableπstate operation dependent on fabrication and thermal variations. In this article, the sensitivity ofJcto temperature and fabrication process parameters is quantified for SFS junctions with weak ferromagnetic barriers. A methodology is developed to determine allowable parameter margins for junctions used as phase shifters or active switching elements. An algorithm is introduced to generate design guidelines in terms of acceptable ranges of thickness and spin-flip scattering for a targetJc. Nominal barrier thickness regions are identified in which strong sensitivity to variation and second harmonic contribution in the current–phase relationship can compromise stable circuit operation. These results provide practical guidelines for robustπ-junction operation in superconducting digital circuits.
Superconducting digital logic technology, Rapid Single Flux Quantum (RSFQ), is established as the fastest technology in microelectronics based on Josephson junction devices. Technological challenges in large scale integration of superconductor circuits (RSFQ) namely: flux trapping, low power dissipation and multi-chip modules are addressed here. One of the main limitations of the integration of the RSFQ circuits is flux trapping, which arises due to the presence of residual magnetic field during transition of the circuit into superconducting state. Flux trapping is an unusual problem specific in only superconducting circuits. The effect of flux trapping in RSFQ circuits is studied, with a controlled 3-D magnetic field setup, quantitatively. Layout configuration with different moat patterns making RSFQ circuits tolerant to external magnetic field up-to 20mG was also developed. Low power issue was addressed by developing a new logic family. Power independent logic, an improved form of RSFQ logic, enables the circuits to operate only when needed and circuits can be switched off the remaining time; thereby eliminating static power consumption by retaining the logic state of the circuit. Flux trapping has also beeninvestigated in power independent cells. Current recycling is a technique to reduce the bias current applied for the operation of the RSFQ circuits. In this technique the cells are biased by serial connections. The reduction in supply current is proportional to number of blocks connected in series The effect of magnetic field on the operating margins of the current recycling circuits has also been studied. Operation of Multi-chip modules, one of the most viable solutions to develop large scale circuits, was demonstrated. Multi-chip modules with lithographically designed bumps is presented where data transmission rate between two superconducting chips exceed 100GHz. Finally, the development of the multi-modulator ADC for low noisefront end under-development is discussed.
Abstract Fast phase logic (FPL) is a novel digital superconductor electronic (SCE) logic family that employs multiple junction types, including switching 0-Josephson junctions (0-JJs), non-switching 0-JJ stacks, and π -JJs. FPL enables flexible, automatable cell layouts, faster pulse propagation, reduced bias current via phase-shifting π -JJs, and minimized inductive loops, thereby reducing susceptibility to trapped flux and crosstalk. A fabrication process to support FPL is proposed. NbTiN superconductors offer small grain sizes, smooth surfaces, and thermal stability up to 400 ∘ C, while high- J c , self-shunted JJs enable compact devices. AlN dielectrics provide good crystal matching to NbTiN, improving superconducting properties. Projections indicate that FPL, combined with the proposed process, can achieve a two-order-of-magnitude increase in integration density over conventional RSFQ logic and a five-fold reduction in supply current. The increased density reduces latency and improves computational throughput, while NbTiN-based devices provide higher output voltage and impedance, improving compatibility with CMOS circuits. Further fabrication advancements, such as higher- J c NbTiN-based JJs, higher processing temperatures, and stacked JJ structures, could enhance FPL implementation and scalability toward very large-scale integration. FPL has the potential to significantly advance SCE technology, with near-term applications in accelerator cores for signal processing and artificial intelligence, and long-term potential in supercomputing. Its advantages are evaluated through an architectural study of a fast Fourier transform circuit, with comparisons to CMOS and SFQ technologies for digital electronics.
Superconductive electronics and, specifically, single flux quantum (SFQ) circuits are attracting significant attention as a promising ultra-low power and ultra-high speed circuit technology for beyond CMOS exascale supercomputing. Superconductive electronics is suitable for large scale, energy efficient, stationary cloud computing, ”big data” applications, and ultra-high speed neural networks. Significant development in the design and manufacture of superconductive electronics for prospective exascale computing systems has led to device densities exceeding 4.2×10^6 Josephson junctions (JJs) per cm2 – sufficient to enable large scale SFQ systems. The lack of electronic design automation (EDA) tools, however, is currently a serious issue affecting the development of complex SFQ circuits. Advances in EDA algorithms and design and analysis methodologies and techniques are therefore required to enhance the development of VLSI complexity SFQ systems. In this dissertation, issues and solutions to enable, connect, and secure VLSI complexity SFQ system are presented. Topics such as interconnects, ultra-high speed clocking and synchronization, signal interfaces, and deep scaling of superconductive structures are described, and related design methodologies, algorithms, circuits, and expressions are proposed. On-chip signal routing has become an issue of growing importance in modern VLSI complexity SFQ systems. Specialized routing methods for these systems are presented. The routing methods include passive transmission lines as global interconnect and Josephson transmission lines as local interconnect. Guidelines are provided for determining when to use global and local interconnects. Novel methodologies, algorithms, and expressions have been developed to manage resonance, flux trapping, and coupling in VLSI complexity SFQ circuits. The design of an SFQ clock distribution network is a challenging problem due to timing uncertainties at very high frequencies, gate-level pipelining, and fanout constraints. Near zero skew clock tree targeting large scale SFQ circuits is proposed to improve the global timing process while eliminating skew uncertainty. To enable higher fanout, area efficient splitter topologies are developed, producing a clock network suitable for large scale SFQ systems. All-JJ superconductive circuits based on bistable superconductor-ferromagnet-superconductor are presented to enable nanometer feature sizes for VLSI superconductive systems. These specialized guidelines, algorithms, and circuits enable deep scaling of superconductive systems for stationary high speed, ultra-low energy applications.
The 2ϕ-Josephson junctions (JJs), characterized by a dominant second harmonic in the current-phase relationship (CPR), are promising devices for low-power, high-density superconducting digital logic. These junctions eliminate the need for on-chip inductors to store magnetic flux and they reduce bias current requirements. In practical implementations, both first and second harmonic components are typically present in the CPR, affecting the junction dynamics and circuit operation. Understanding this behavior is essential for the reliable design of superconducting logic circuits utilizing these junctions, such as half flux quantum (HFQ) circuits. In this article, a compact Verilog-A model for 2ϕ-JJs is presented that captures the nonlinear behavior of the junctions, accounting for both harmonic contributions and their impact on damping. Two parameter sets are derived from experimental data corresponding to junctions with weak ferromagnetic barriers and ferromagnetic insulator barriers. Based on the inferred parameters, models of each junction type are developed. The model is validated against published experimental results and simulated within a D flip flop cell, demonstrating its use for superconducting circuit design and analysis, including evaluation of circuit behavior under nonideal junction conditions. Stability issues and failure mechanisms introduced by a nonzero first harmonic are analyzed, and underlying junction dynamics are examined to explain the reduction in circuit parameter margins.
Josephson junction-based superconducting logic families have been proposed to implement analog and digital signals, which can achieve low energy dissipation and ultra-fast switching speed. There are two representative technologies: DC-biased RSFQ (rapid single flux quantum) technology and its variants that achieve a verified speed of 370 Ghz, and AC-biased AQFP (adiabatic quantum-flux-parametron) that achieves an energy dissipation near quantum limits. Despite extraordinary characteristics of the superconducting logic families, many technical challenges remain, including the choice of circuit fabrics and architectures that utilize the SFQ technology and the development of effective design automation methodologies and tools. This paper presents our work on developing design flows and tools for DC- and AC-biased SFQ circuits, leveraging unique characteristics and design requirements of the SFQ logic families. More precisely, physical design algorithms, including placement, clock tree routing, and signal routing algorithms targeting RSFQ circuits are presented first. Next, a majority/minority gate-based automatic synthesis framework targeting AQFP logic circuits is described. Finally, experimental results to demonstrate the efficacy of the proposed framework and tools are presented.