Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Physics Photonics

Wafer-level fabrication of alkali vapor cells using in-situ atomic deposition

Doug Bopp, Vincent N. Maurice, John E. Kitching

Published Dec 14, 2020• 44 citations
Publisher

Abstract

Abstract We demonstrate a new technique for filling mm-scale microfabricated silicon and glass cavities with alkali vapors at the wafer-scale. A single etched silicon wafer contains an array of cavities containing alkali precursor materials offset laterally from the cell array. The wafer is heated to create an array of alkali droplets on an upper glass wafer, which is then translated laterally under vacuum and bonded to create the cells. This technique can be implemented in a commercially available bonding tool, allows the fabrication of cells with arbitrary buffer gas contents and pressures and can potentially produce cells with dimensions below 100 µm.

DOI
10.1088/2515-7647/abcbe5

Related papers

Microfabricated Alkali Atom Vapor Cells for Chip Scale Atomic Clock

M.-Z. Huang, Jiashan Zhu, Guangfeng Shi +2 more

In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.

Annual Conference of the Chinese Society of Micro-Nano Technology (CSMNT)•Nov 22, 2017•0 citations

Wafer-scale fabrication of evacuated alkali vapor cells

Yang Li, Donggyu B. Sohn, Matthew T. Hummon +2 more

We describe a process for fabricating a wafer-scale array of alkali metal vapor cells with low residual gas pressure. We show that by etching long, thin channels between the cells on the Si wafer surface, the residual gas pressure in the evacuated vapor cell can be reduced to below 0.5 kPa (4 Torr) with a yield above 50%. The low residual gas pressure in these mass-producible alkali vapor cells can enable a new generation of low-cost chip-scale atomic devices such as vapor cell optical clocks, wavelength references, and Rydberg sensors.

arXiv:2405.11088•Optics Letters•Aug 14, 2024•12 citations

Locally sealed microfabricated vapor cells filled from an ex situ Cs source

Linda Péroux, A. Dewilde, Ravinder Chutani +8 more

Microfabricated alkali vapor cells are key to enable miniature devices such as atomic clocks and optically pumped magnetometers with reduced size, weight, and power. Yet, more versatile fabrication methods are still needed to further expand their use cases. Here, we demonstrate an approach to collectively fill and seal microfabricated cesium cells using locally sealed microchannels patterned within one of the glass substrates comprising the cells. Unlike current methods that rely on wafer-level anodic bonding as the last sealing step, an approach based on local sealing opens the path to features so far limited to traditional glass-blown cells, including the ability to deposit temperature-sensitive antirelaxation coatings, reaching lower background gas pressure without an additional gettering material or filling with diverse atomic or molecular species.

arXiv:2502.10829•Applied Physics Letters•Apr 1, 2025•5 citations

Wafer-level filling of microfabricated atomic vapor cells based on thin-film deposition and photolysis of cesium azide

Li‐Anne Liew, John Moreland, Vladislav P. Gerginov

The thin-film deposition and photodecomposition of cesium azide are demonstrated and used to fill arrays of miniaturized atomic resonance cells with cesium and nitrogen buffer gas for chip-scale atomic-based instruments. Arrays of silicon cells are batch fabricated on wafers into which cesium azide is deposited by vacuum thermal evaporation. After vacuum sealing, the cells are irradiated with ultraviolet radiation, causing the azide to photodissociate into pure cesium and nitrogen in situ. This technology integrates the vapor-cell fabrication and filling procedures into one continuous and wafer-level parallel process, and results in cells that are optically transparent and chemically pure.

Applied Physics Letters•Mar 12, 2007•85 citations

Microfabricated alkali atom vapor cells

Li‐Anne Liew, Svenja A. Knappe, John Moreland +3 more

We describe the fabrication of chip-sized alkali atom vapor cells using silicon micromachining and anodic bonding technology. Such cells may find use in highly miniaturized atomic frequency references or magnetometers. The cells consist of cavities etched in silicon, with internal volumes as small as 1 mm3. Two techniques for introducing cesium and a buffer gas into the cells are described: one based on chemical reaction between cesium chloride and barium azide, and the other based on direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption and coherent population trapping resonances were measured in the cells.

Applied Physics Letters•Apr 1, 2004•377 citations

Wafer-scale fabrication of alkali vapor cells

Yang Li, Marlou R. Slot, Dongyu Sohn +3 more

This paper describes the progress made in developing wafer-scale fabrication process of alkali vapor cells for chip-scale atomic devices such as Coherent Population Trapping (CPT) clocks, optical frequency standards and Rydberg-atom-based sensors. The wafer level fabrication process uses anodic bonding and introduces alkali atoms by chemical reactions of Alkali Chloride with Barium Azide. This method is compatible to make cells with a wide range of buffer gas species and pressures, including evacuated cells. We improve the yield of the cells to above 50%. We will show the residual gas pressures for evacuated cells are mostly consistent with zero within the resolution of the saturation absorption spectroscopy measurement. The temperature coefficients for the CPT spectroscopy are improved with Ar-N2 mixture buffer gas compared with only N2 buffer gas.

Optical and Quantum Sensing and Precision Metrology II•Mar 19, 2025•0 citations
Abstract We demonstrate a new technique for filling mm-scale microfabricated silicon and glass cavities with alkali vapors at the wafer-scale. A single etched silicon wafer contains an array of cavities containing alkali precursor materials offset laterally from the cell array. The wafer is heated to create an array of alkali droplets on an upper glass wafer, which is then translated laterally under vacuum and bonded to create the cells. This technique can be implemented in a commercially available bonding tool, allows the fabrication of cells with arbitrary buffer gas contents and pressures and can potentially produce cells with dimensions below 100 µm.
In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.
We describe a process for fabricating a wafer-scale array of alkali metal vapor cells with low residual gas pressure. We show that by etching long, thin channels between the cells on the Si wafer surface, the residual gas pressure in the evacuated vapor cell can be reduced to below 0.5 kPa (4 Torr) with a yield above 50%. The low residual gas pressure in these mass-producible alkali vapor cells can enable a new generation of low-cost chip-scale atomic devices such as vapor cell optical clocks, wavelength references, and Rydberg sensors.
Microfabricated alkali vapor cells are key to enable miniature devices such as atomic clocks and optically pumped magnetometers with reduced size, weight, and power. Yet, more versatile fabrication methods are still needed to further expand their use cases. Here, we demonstrate an approach to collectively fill and seal microfabricated cesium cells using locally sealed microchannels patterned within one of the glass substrates comprising the cells. Unlike current methods that rely on wafer-level anodic bonding as the last sealing step, an approach based on local sealing opens the path to features so far limited to traditional glass-blown cells, including the ability to deposit temperature-sensitive antirelaxation coatings, reaching lower background gas pressure without an additional gettering material or filling with diverse atomic or molecular species.
The thin-film deposition and photodecomposition of cesium azide are demonstrated and used to fill arrays of miniaturized atomic resonance cells with cesium and nitrogen buffer gas for chip-scale atomic-based instruments. Arrays of silicon cells are batch fabricated on wafers into which cesium azide is deposited by vacuum thermal evaporation. After vacuum sealing, the cells are irradiated with ultraviolet radiation, causing the azide to photodissociate into pure cesium and nitrogen in situ. This technology integrates the vapor-cell fabrication and filling procedures into one continuous and wafer-level parallel process, and results in cells that are optically transparent and chemically pure.
We describe the fabrication of chip-sized alkali atom vapor cells using silicon micromachining and anodic bonding technology. Such cells may find use in highly miniaturized atomic frequency references or magnetometers. The cells consist of cavities etched in silicon, with internal volumes as small as 1 mm3. Two techniques for introducing cesium and a buffer gas into the cells are described: one based on chemical reaction between cesium chloride and barium azide, and the other based on direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption and coherent population trapping resonances were measured in the cells.
This paper describes the progress made in developing wafer-scale fabrication process of alkali vapor cells for chip-scale atomic devices such as Coherent Population Trapping (CPT) clocks, optical frequency standards and Rydberg-atom-based sensors. The wafer level fabrication process uses anodic bonding and introduces alkali atoms by chemical reactions of Alkali Chloride with Barium Azide. This method is compatible to make cells with a wide range of buffer gas species and pressures, including evacuated cells. We improve the yield of the cells to above 50%. We will show the residual gas pressures for evacuated cells are mostly consistent with zero within the resolution of the saturation absorption spectroscopy measurement. The temperature coefficients for the CPT spectroscopy are improved with Ar-N2 mixture buffer gas compared with only N2 buffer gas.