Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2502.10829 · Applied Physics Letters

Locally sealed microfabricated vapor cells filled from an ex situ Cs source

Linda Péroux, A. Dewilde, Ravinder Chutani, Aurelien Mazzamurro, Jérémy Bonhomme, Andrei Mursa, Jean‐François Clément, Abdelkrim Talbi, Philippe Pernod, Nicolas Passilly, Vincent N. Maurice

Published Apr 1, 2025• 5 citations
arXivHTMLPDF

Abstract

Microfabricated alkali vapor cells are key to enable miniature devices such as atomic clocks and optically pumped magnetometers with reduced size, weight, and power. Yet, more versatile fabrication methods are still needed to further expand their use cases. Here, we demonstrate an approach to collectively fill and seal microfabricated cesium cells using locally sealed microchannels patterned within one of the glass substrates comprising the cells. Unlike current methods that rely on wafer-level anodic bonding as the last sealing step, an approach based on local sealing opens the path to features so far limited to traditional glass-blown cells, including the ability to deposit temperature-sensitive antirelaxation coatings, reaching lower background gas pressure without an additional gettering material or filling with diverse atomic or molecular species.

DOI
10.1063/5.0265624

Related papers

Versatile microfabricated alkali vapor cells using local sealing

Vincent N. Maurice, Ravinder Chutani, Clément Carlé +7 more

We report on a new technique to form and seal microfabricated cells that alleviates some of the limitations imposed by current solutions. The technique consists in integrating single-use sealing structures that can be actuated through laser irradiation, either to isolate cavities from each other or to connect them. Inspired by the well-established glass-blowing techniques, it reproduces on a wafer the “make-seal” and “break-seal” features found in conventional cell filling setups. By allowing cells to be evacuated, filled and sealed after having been fully-formed, this technique opens new venues for atomic devices. Here, we demonstrate both features and present one use case where alkali dispensers are used in association with non-noble gasses despite their gettering ability.

•Apr 24, 2022•0 citations

Microfabricated vapor cells filled with a cesium dispensing paste for miniature atomic clocks

Vincent N. Maurice, J. Rutkowski, Eric Kroemer +6 more

A method for filling alkali vapor cells with cesium from a dispensing paste is proposed and its compliance with miniature atomic clock applications is evaluated. The paste is an organic-inorganic composition of cesium molybdate, zirconium-aluminum powder, and a hybrid organic-inorganic binder. It is compatible with collective deposition processes such as micro-drop dispensing, which can be done under ambient atmosphere at the wafer-level. After deposition and sealing by anodic bonding, cesium is released from the consolidated paste through local heating with a high power laser. Linear absorption signals have been observed over one year in several cells, showing a stable atomic density. For further validation of this technology for clock applications, one cell has been implemented in a coherent population trapping clock setup to monitor its frequency stability. A fractional frequency aging rate around –4.4 × 10−12 per day has been observed, which is compliant with a clock frequency instability below 1 × 10−11 at one day integration time. This filling method can drastically reduce the cost and the complexity of alkali vapor cell fabrication.

Applied Physics Letters•Apr 17, 2017•42 citations

Microfabricated Alkali Atom Vapor Cells for Chip Scale Atomic Clock

M.-Z. Huang, Jiashan Zhu, Guangfeng Shi +2 more

In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.

Annual Conference of the Chinese Society of Micro-Nano Technology (CSMNT)•Nov 22, 2017•0 citations

Wafer-level fabrication of alkali vapor cells using in-situ atomic deposition

Doug Bopp, Vincent N. Maurice, John E. Kitching

Abstract We demonstrate a new technique for filling mm-scale microfabricated silicon and glass cavities with alkali vapors at the wafer-scale. A single etched silicon wafer contains an array of cavities containing alkali precursor materials offset laterally from the cell array. The wafer is heated to create an array of alkali droplets on an upper glass wafer, which is then translated laterally under vacuum and bonded to create the cells. This technique can be implemented in a commercially available bonding tool, allows the fabrication of cells with arbitrary buffer gas contents and pressures and can potentially produce cells with dimensions below 100 µm.

Journal of Physics Photonics•Dec 14, 2020•44 citations

Optical pumping in a microfabricated Rb vapor cell using a microfabricated Rb discharge light source

Vinu Venkatraman, Songbai Kang, C. Affolderbach +2 more

Miniature (<few cm3) vapor-cell based devices using optical pumping of alkali atoms, such as atomic clocks and magnetometers, today mostly employ vertical-cavity surface-emitting lasers as pump light sources. Here, we report on the demonstration of optical pumping in a microfabricated alkali vapor resonance cell using (1) a microfabricated Rb discharge lamp light source, as well as (2) a conventional glass-blown Rb discharge lamp. The microfabricated Rb lamp cell is a dielectric barrier discharge (DBD) light source, having the same inner cell volume of around 40 mm3 as that of the resonance cell, both filled with suitable buffer gases. A miniature (∼2 cm3 volume) test setup based on the Mz magnetometer interrogation technique was used for observation of optical-radiofrequency double-resonance signals, proving the suitability of the microfabricated discharge lamp to introduce efficient optical pumping. The pumping ability of this light source was found to be comparable to or even better than that of a conventional glass-blown lamp. The reported results indicate that the micro-fabricated DBD discharge lamp has a high potential for the development of a new class of miniature atomic clocks, magnetometers, and quantum sensors.

Applied Physics Letters•Feb 3, 2014•15 citations

Microfabricated alkali atom vapor cells

Li‐Anne Liew, Svenja A. Knappe, John Moreland +3 more

We describe the fabrication of chip-sized alkali atom vapor cells using silicon micromachining and anodic bonding technology. Such cells may find use in highly miniaturized atomic frequency references or magnetometers. The cells consist of cavities etched in silicon, with internal volumes as small as 1 mm3. Two techniques for introducing cesium and a buffer gas into the cells are described: one based on chemical reaction between cesium chloride and barium azide, and the other based on direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption and coherent population trapping resonances were measured in the cells.

Applied Physics Letters•Apr 1, 2004•377 citations
Microfabricated alkali vapor cells are key to enable miniature devices such as atomic clocks and optically pumped magnetometers with reduced size, weight, and power. Yet, more versatile fabrication methods are still needed to further expand their use cases. Here, we demonstrate an approach to collectively fill and seal microfabricated cesium cells using locally sealed microchannels patterned within one of the glass substrates comprising the cells. Unlike current methods that rely on wafer-level anodic bonding as the last sealing step, an approach based on local sealing opens the path to features so far limited to traditional glass-blown cells, including the ability to deposit temperature-sensitive antirelaxation coatings, reaching lower background gas pressure without an additional gettering material or filling with diverse atomic or molecular species.
We report on a new technique to form and seal microfabricated cells that alleviates some of the limitations imposed by current solutions. The technique consists in integrating single-use sealing structures that can be actuated through laser irradiation, either to isolate cavities from each other or to connect them. Inspired by the well-established glass-blowing techniques, it reproduces on a wafer the “make-seal” and “break-seal” features found in conventional cell filling setups. By allowing cells to be evacuated, filled and sealed after having been fully-formed, this technique opens new venues for atomic devices. Here, we demonstrate both features and present one use case where alkali dispensers are used in association with non-noble gasses despite their gettering ability.
A method for filling alkali vapor cells with cesium from a dispensing paste is proposed and its compliance with miniature atomic clock applications is evaluated. The paste is an organic-inorganic composition of cesium molybdate, zirconium-aluminum powder, and a hybrid organic-inorganic binder. It is compatible with collective deposition processes such as micro-drop dispensing, which can be done under ambient atmosphere at the wafer-level. After deposition and sealing by anodic bonding, cesium is released from the consolidated paste through local heating with a high power laser. Linear absorption signals have been observed over one year in several cells, showing a stable atomic density. For further validation of this technology for clock applications, one cell has been implemented in a coherent population trapping clock setup to monitor its frequency stability. A fractional frequency aging rate around –4.4 × 10−12 per day has been observed, which is compliant with a clock frequency instability below 1 × 10−11 at one day integration time. This filling method can drastically reduce the cost and the complexity of alkali vapor cell fabrication.
In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.
Abstract We demonstrate a new technique for filling mm-scale microfabricated silicon and glass cavities with alkali vapors at the wafer-scale. A single etched silicon wafer contains an array of cavities containing alkali precursor materials offset laterally from the cell array. The wafer is heated to create an array of alkali droplets on an upper glass wafer, which is then translated laterally under vacuum and bonded to create the cells. This technique can be implemented in a commercially available bonding tool, allows the fabrication of cells with arbitrary buffer gas contents and pressures and can potentially produce cells with dimensions below 100 µm.
Miniature (<few cm3) vapor-cell based devices using optical pumping of alkali atoms, such as atomic clocks and magnetometers, today mostly employ vertical-cavity surface-emitting lasers as pump light sources. Here, we report on the demonstration of optical pumping in a microfabricated alkali vapor resonance cell using (1) a microfabricated Rb discharge lamp light source, as well as (2) a conventional glass-blown Rb discharge lamp. The microfabricated Rb lamp cell is a dielectric barrier discharge (DBD) light source, having the same inner cell volume of around 40 mm3 as that of the resonance cell, both filled with suitable buffer gases. A miniature (∼2 cm3 volume) test setup based on the Mz magnetometer interrogation technique was used for observation of optical-radiofrequency double-resonance signals, proving the suitability of the microfabricated discharge lamp to introduce efficient optical pumping. The pumping ability of this light source was found to be comparable to or even better than that of a conventional glass-blown lamp. The reported results indicate that the micro-fabricated DBD discharge lamp has a high potential for the development of a new class of miniature atomic clocks, magnetometers, and quantum sensors.
We describe the fabrication of chip-sized alkali atom vapor cells using silicon micromachining and anodic bonding technology. Such cells may find use in highly miniaturized atomic frequency references or magnetometers. The cells consist of cavities etched in silicon, with internal volumes as small as 1 mm3. Two techniques for introducing cesium and a buffer gas into the cells are described: one based on chemical reaction between cesium chloride and barium azide, and the other based on direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption and coherent population trapping resonances were measured in the cells.