One of the remaining challenges in the application of superconducting electronics is the interfacing between superconducting and semiconducting environments. The voltage and speed mismatch between RSFQ pulses and semiconducting read-out electronics makes it necessary to amplify as well as stretch the RSFQ pulses. Moreover, circuits based on HTS (High Temperature Superconductor) technology are very attractive since they can operate under considerably relaxed cooling effort, which is one of the main problems with LTS (Low Temperature Superconductor) circuits. Within the European project SuperADC, a HTS second order sigma delta modulator and a pulse stretcher, used as an interface between the modulator and the first semi-conducting amplifier stage, have been designed at Twente University and will be presented here.
One of the remaining challenges in the application of superconducting electronics is the interfacing between superconducting and semiconducting environments. The voltage and speed mismatch between RSFQ pulses and semiconducting read-out electronics makes it necessary to amplify as well as stretch the RSFQ pulses. Moreover, circuits based on HTS (High Temperature Superconductor) technology are very attractive since they can operate under considerably relaxed cooling effort, which is one of the main problems with LTS (Low Temperature Superconductor) circuits. Within the European project SuperADC, a HTS second order sigma delta modulator and a pulse stretcher, used as an interface between the modulator and the first semi-conducting amplifier stage, have been designed at Twente University and will be presented here.
The main topic of this thesis is the evaluation of performance of super-conducting rst- and second-order low-pass sigma-delta modulators. Superconducting electronics comprise characteristics such as very high switching speed, natural quantization, high sensitivity and low noise, proper-ties that are all essential for modulators used in high performance analog-to-digital converters (ADC). Sigma-delta modulators trade speed for improved resolution using feedback mechanisms making superconducting electronics an interesting alternative technology for the implementation. With linear models and device-level simulations the performance of these modulators have been evaluated. The linear model of the rst-order sigma-delta modulator shows that the performance, for a given oversampling ratio, only depends on the cut-o frequency of the RL-lter used. This is veried by device-level simulations and the results from the two methods are in good agreement. Device-level simulations of the second-order sigma-delta modu-
We have successfully fabricated and tested a high temperature superconducting (HTS) sigma-delta modulator for analogue-to-digital conversion. This is the first demonstration of a GHz sampling A-to-D in HTS. The 15-junction single-flux-quantum (SFQ) circuit, fabricated using an epitaxial multilayer HTS process with YBCO/Co-YBCO/YBCO edge junctions, was internally clocked at 27 GHz and used to convert a 5.01 MHz signal. The modulator demonstrated a spur-free dynamic range of more than 75 dB. Two-tone measurements with 5.01 MHz and 5.51 MHz signals demonstrated third-order intermodulation products to be lower than -59 dBc. Demonstration of a functional HTS modulator represents a significant milestone in the development of high dynamic range ADCs suitable for such applications as surveillance radar.
We have been developing a superconducting second-order sigma-delta analog-to-digital converter with a large bandwidth and a large dynamic range for software radio applications. In a superconducting second-order sigma-delta modulator utilizing a passive integrator and single-flux-quantum (SFQ) feedback, gain to compensate the large attenuation in the passive integrator of the modulator is required to obtain a large dynamic range. In this paper, a second-order modulator utilizing multi-flux-quantum (MFQ) generators creating the needed gain is reported and the design and experimental test results of the elementary circuits including a comparator, a first-order modulator, and the MFQ generator are described. The digital outputs of the comparator and the first-order modulator were experimentally evaluated, where the input dependence of the comparator switching probability and the noise-shaping properties of the modulator were clearly observed. The low speed operation of the MFQ generator creating three SFQ pulses was experimentally confirmed. The other circuits were also tested at low frequencies.
Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).
Superconducting digital circuits are capable of producing high dynamic range analog-to-digital converters (ADCs). We present sigma-delta architectures using large (>100) oversampling ratios to give signal-to-noise ratios of greater than 100 dB in simulation. Three distinct designs, using two distinct mechanisms for feedback, are presented. All of the designs use only shunted junctions, and are therefore compatible with HTS SNS junctions. Simulations are presented for a modulator which creates feedback pulses by SQUID lobe-crossings, a modulator which uses the transresistance of a SQUID for feedback, and a modulator which uses threshold crossings in both the first and second loops for feedback.
Interface circuits are the key components that enable the hybrid integration of superconductor and semiconductor digital electronics. The design requirements of superconductor-semiconductor interface circuits vary depending on the application, such as high-performance classical computing, superconducting quantum computing, and digital signal processing. In this survey, various interface circuits are categorized based on the working principle and structure. The superconducting output drivers are explored, which are capable of converting and amplifying, e.g., single flux quantum (SFQ) voltage pulses, to voltage levels that semiconductor circuits can process. Several trade-offs between circuit- and system-level design parameters are examined. Accordingly, parameters such as the data rate, output voltage, power dissipation, layout area, thermal/heat load of cryogenic cables, and bit-error rate are considered.