The main topic of this thesis is the evaluation of performance of super-conducting rst- and second-order low-pass sigma-delta modulators. Superconducting electronics comprise characteristics such as very high switching speed, natural quantization, high sensitivity and low noise, proper-ties that are all essential for modulators used in high performance analog-to-digital converters (ADC). Sigma-delta modulators trade speed for improved resolution using feedback mechanisms making superconducting electronics an interesting alternative technology for the implementation. With linear models and device-level simulations the performance of these modulators have been evaluated. The linear model of the rst-order sigma-delta modulator shows that the performance, for a given oversampling ratio, only depends on the cut-o frequency of the RL-lter used. This is veried by device-level simulations and the results from the two methods are in good agreement. Device-level simulations of the second-order sigma-delta modu-
The main topic of this thesis is the evaluation of performance of super-conducting rst- and second-order low-pass sigma-delta modulators. Superconducting electronics comprise characteristics such as very high switching speed, natural quantization, high sensitivity and low noise, proper-ties that are all essential for modulators used in high performance analog-to-digital converters (ADC). Sigma-delta modulators trade speed for improved resolution using feedback mechanisms making superconducting electronics an interesting alternative technology for the implementation. With linear models and device-level simulations the performance of these modulators have been evaluated. The linear model of the rst-order sigma-delta modulator shows that the performance, for a given oversampling ratio, only depends on the cut-o frequency of the RL-lter used. This is veried by device-level simulations and the results from the two methods are in good agreement. Device-level simulations of the second-order sigma-delta modu-
Superconducting digital circuits are capable of producing high dynamic range analog-to-digital converters (ADCs). We present sigma-delta architectures using large (>100) oversampling ratios to give signal-to-noise ratios of greater than 100 dB in simulation. Three distinct designs, using two distinct mechanisms for feedback, are presented. All of the designs use only shunted junctions, and are therefore compatible with HTS SNS junctions. Simulations are presented for a modulator which creates feedback pulses by SQUID lobe-crossings, a modulator which uses the transresistance of a SQUID for feedback, and a modulator which uses threshold crossings in both the first and second loops for feedback.
Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).
High performance oversampling delta-sigma data converters require high clock rates and accurate feedback of the digital output to the analog regime. Superconductor modulators offer the unique advantages of clock rates in the tens-of-gigahertz, comparator switching energy below attoJoules, and quantum-accurate digital-to-analog feedback. We have designed a two-loop baseband modulator whose noise transfer function was calculated using a simple, linear circuit model. The circuit was fabricated in a commercial superconductor IC process with 4.5 kA-per-square cm Josephson junctions and 1.5 micron minimum feature size. The circuit was tested at a derated sample rate of 5 GHz. Measured signal-to-noise dynamic range was 81 dB over a 10 MHz band. Third-order intercept was measured to be +24 dBsat in two-tone test. The measured noise transfer function was in excellent agreement with our linear model. The linear model indicates that with appropriate parameter values, this family of modulators extrapolates to significantly higher performance.
We have been developing a superconducting second-order sigma-delta analog-to-digital converter with a large bandwidth and a large dynamic range for software radio applications. In a superconducting second-order sigma-delta modulator utilizing a passive integrator and single-flux-quantum (SFQ) feedback, gain to compensate the large attenuation in the passive integrator of the modulator is required to obtain a large dynamic range. In this paper, a second-order modulator utilizing multi-flux-quantum (MFQ) generators creating the needed gain is reported and the design and experimental test results of the elementary circuits including a comparator, a first-order modulator, and the MFQ generator are described. The digital outputs of the comparator and the first-order modulator were experimentally evaluated, where the input dependence of the comparator switching probability and the noise-shaping properties of the modulator were clearly observed. The low speed operation of the MFQ generator creating three SFQ pulses was experimentally confirmed. The other circuits were also tested at low frequencies.
A wide variety of applications, ranging from radio-frequency (RF) receivers for broadband communications and signal detection, on earth and in space, would benefit from high-performance superconductor analog-to-digital converters (ADCs), based on magnetic flux quantization and fast switching Josephson junctions. Superconductor ADCs are capable of very high sample rates (100 GHz or more), very high linearity, and high sensitivity. Nyquist-rate ADCs use the high sample rate to digitize a wide instantaneous bandwidth (tens of GHz) and are useful for wideband spectrum monitoring as well as high-end scientific instrumentation. Delta and delta-sigma oversampling ADCs use the high linearity to achieve programmable trade-off between dynamic range and instantaneous bandwidth. These lowpass and bandpass ADCs have been used for direct digitization of narrower (tens to hundreds of MHz) RF bands in the 1-20 GHz range for a variety of communications, intelligence, electronic warfare, and radar applications. Another application area of these cryogenic ADCs is for outputs of cryogenic sensor arrays and terahertz mixers. Recent advances in various classes of ADCs for different applications are described.
Ultrafast switching speed, low power, natural quantization of magnetic flux, quantum accuracy, and low noise of cryogenic superconductor circuits enable fast and accurate data conversion between the analog and digital domains. Based on rapid single-flux quantum (RSFQ) logic, these integrated circuits are capable of achieving performance levels unattainable by any other technology. Two major classes of superconductor analog-to-digital converters (ADCs) are being developed - Nyquist sampling and oversampling converters. Complete systems with digital sampling at rates of /spl sim/20 GHz and above have been demonstrated using low-temperature superconductor device technology. Some ADC components have also been implemented using high-temperature superconductors. Superconductor ADCs have unique applications in true digital-RF communications, broadband instrumentation, and digital sensor readout. Their designs, test results, and future development trends are reviewed.