Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Magnetics

Refractory material SIS junction structures

Victor Y. Belitsky, V. Gubankov, V. P. Koshelets, G. A. Ovsyannikov, I. L. Serpuchenko, S. V. Shitov, Michael A. Tarasov, Alexander N. Vystavkin

Published Mar 1, 1987• 5 citations
Publisher

Abstract

Niobium based SIS junction structures for microwave receiving devices were investigated. The possibility of the mixing efficiency improving for Nb-Al2O3-Nb junctions with a negative resistance on I-V curve near the gap voltage has been demonstrated. Comparative microwave investigation of the parallel and series DC biased arrays shows the advantage of the first one. SIS junction capacitance has been compensated with microstrip or lumped elements at the signal frequency. Such compensated structures were investigated at frequencies 38 and 76 GHz both in waveguide and quasioptic systems.

DOI
10.1109/tmag.1987.1065119

Related papers

SNAP structures with Nb-AlO/sub x/-Nb junctions for MM-wave receivers

An. B. Ermakov, V. P. Koshelets, I. L. Serpuchenko +3 more

High-quality small-area Nb-AlO/sub x/-Nb junctions have been fabricated by the selective niobium anodization process (SNAP). The influence of the preparation conditions on the junction properties were investigated. Numerical calculations based on I-V (current-voltage) characteristics measured by a data acquisition system were used to simulate the mixer performance. It has been shown that the knee-shaped structure on the I-V curve of refractory material junctions significantly affects the signal properties of the mixer. The signal and noise properties for different types of integrated SIS (superconductor-insulator-superconductor) mixing elements have been investigated experimentally in the frequency range of 37-53 GHz; the mixer conversion loss was as low as 4 dB at 45 GHz. The mixing elements consist of an odd number of SIS junctions connected in series for RF and in parallel for DC biasing. The DC bias wiring and IF (intermediate frequency) filters of these structures were designed to provide tuning out of junction capacitance and thin-film-electrode inductance.>

IEEE Transactions on Magnetics•Mar 1, 1989•7 citations

Parallel biased SIS-arrays for mm wave mixers: main ideas and experimental verification

An. B. Ermakov, V. P. Koshelets, Sergey Kovtonyuk +1 more

The possibility of overcoming the main drawbacks of the traditional series arrays by parallel connection of the SIS (superconductor-insulator-superconductor) junctions for DC and IF are demonstrated experimentally. The proposed mixing elements avoid the influence of the junction nonuniformity in the array, provide the optimal matching on both RF input and IF output, and tune out junction capacitance. Experimentally tested arrays contained up to eight high-quality Nb-AlO/sub x/-Nb junctions with R/sub n/=20-70 Omega at junction area 8/14 mu m/sup 2/. The best values of T/sub r/ (SSB) were measured to as low as 5 K on the mixer cold input flange in the 45-55-GHz bandwidth at an ambient temperature of 4.2 K. A mixer gain of up to 10 dB was obtained. The gain values were limited by bias stability at very high or even negative array output impedance. An experimental receiver noise temperature (SSB) of less than 20 K has been achieved.

IEEE Transactions on Magnetics•Mar 1, 1991•19 citations

NbTiN Based Tuning Structures for Broadband Nb-Al 2 O >3 -Nb SIS Mixers from 640 GHz-800 GHz

S. Glenz, Sybille Haas, Cornelia E. Honingh +1 more

We present measurements with a prototype waveguide SIS mixer for band 2 (640 GHz – 800 GHz) of HIFI (Heterodyne Instrument for FIRST). The Nb/Al2O3/Nb junctions have an RnA product from 12–18 Ωμm. These junctions are embedded in microstrip circuits tuning out the device capacitance using a NbTiN ground layer and various top conductor materials such as NbTiN, Nb and Al. The NbTiN films are fabricated by DC magnetron sputtering which is optimized for a minimum value of the DC resistivity and for a high critical temperature by varying the sputter pressure, sputter power and Ar:N2 flow. Typical NbTiN film parameters for device fabrication are ρ = 120 μΩcm and Tc = 14.5 K. The best uncorrected noise temperatures we measured so far are for devices with NbTiN/SiO2/Nb tuning. At 4.2 K bath temperature, a standard Yfactor measurement yields uncorrected receiver noise temperatures of 350 K at 642 GHz and 500 K at 810 GHz for 1.5 GHz intermediate frequency. We discuss the effect of the various tuning circuit materials on the mixer performance. In addition, measurements at IF’s between 4 GHz and 8 GHz will be presented.

Softwaretechnik-Trends•Dec 1, 2001•0 citations

High-current-density small-area SIS junctions for high-frequency radio astronomy

Eric E. Bloemhof

At the Smithsonian Astrophysical Observatory, we have been developing expertise in the construction of high-frequency heterodyne receivers using SIS junctions as their first mixing elements. This research has been carried out in support of the Submillimeter Array (SMA), a radio interferometer soon to be built on Mauna Kea that will require multiple reciever systems at a number of bands between 177 GHz and 920 GHz. In this paper, we describe research on the fabrication of all-refractory SIS junctions. To be useful as high-frequency mixers, SIS junctions must have small area and high critical current density. At the lower SMA frequencies, Nb/Al-Oxide/Nb ahs proven to be an ideal material system, and optical photolithography has sufficient resolution for junction definition. At the higher frequencies, NbN/MgO/NbN may enjoy an advantage due to its larger energy gap, and electron-beam lithography may be necessary for defining junctions much smaller than one micron in size. We report good initial results for Nb/Al-Oxide/Nb junctions, fabricated using a self-aligned optical technique, with area $AP 0.5 micrometers 2 and critical current density $AP 10,000 Amp/cm2.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jul 2, 1994•1 citation

Direct detection with Nb-based tunnel junctions at 74 GHz

J. Mees

Apart from the great success of SIS-junctions as mixers in heterodyne receivers there are several other reasons to intensify investigations of SIS-junctions as direct detectors. These devices can be produced as single junctions and arrays for use. in waveguide systems or in planar antennas by standard lithographic techniques. Impedance matching structures and filter elements can be incorporated easily. Recent developments1,2 in junction technology show strong improvements of junction performance. Areas of 0.5μm2 and leakage currents as low as 50nA have been realized. Since the final sensitivity (NEP) of SIS-junctions as direct detectors is limited ultimately by the shot noise of the bias current (NEP∼√IL), a low leakage current IL, is highly important for these devices. Using these improved SIS-junctions, NEP's down to 10-17W/√Hz seem to be possible with He4-cooled devices. A crude estimate for the time constant of a SIS-direct detector yields the inverse of the gap frequency h/∆ or the sumgap frequency h/2∆, which gives very small values of 1 − 10psec.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Oct 1, 1991•1 citation

MM wave quasioptical SIS mixers

Qing Hu, C. A. Mears, P. L. Richards +1 more

The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>

IEEE Transactions on Magnetics•Mar 1, 1989•32 citations
Niobium based SIS junction structures for microwave receiving devices were investigated. The possibility of the mixing efficiency improving for Nb-Al2O3-Nb junctions with a negative resistance on I-V curve near the gap voltage has been demonstrated. Comparative microwave investigation of the parallel and series DC biased arrays shows the advantage of the first one. SIS junction capacitance has been compensated with microstrip or lumped elements at the signal frequency. Such compensated structures were investigated at frequencies 38 and 76 GHz both in waveguide and quasioptic systems.
High-quality small-area Nb-AlO/sub x/-Nb junctions have been fabricated by the selective niobium anodization process (SNAP). The influence of the preparation conditions on the junction properties were investigated. Numerical calculations based on I-V (current-voltage) characteristics measured by a data acquisition system were used to simulate the mixer performance. It has been shown that the knee-shaped structure on the I-V curve of refractory material junctions significantly affects the signal properties of the mixer. The signal and noise properties for different types of integrated SIS (superconductor-insulator-superconductor) mixing elements have been investigated experimentally in the frequency range of 37-53 GHz; the mixer conversion loss was as low as 4 dB at 45 GHz. The mixing elements consist of an odd number of SIS junctions connected in series for RF and in parallel for DC biasing. The DC bias wiring and IF (intermediate frequency) filters of these structures were designed to provide tuning out of junction capacitance and thin-film-electrode inductance.>
The possibility of overcoming the main drawbacks of the traditional series arrays by parallel connection of the SIS (superconductor-insulator-superconductor) junctions for DC and IF are demonstrated experimentally. The proposed mixing elements avoid the influence of the junction nonuniformity in the array, provide the optimal matching on both RF input and IF output, and tune out junction capacitance. Experimentally tested arrays contained up to eight high-quality Nb-AlO/sub x/-Nb junctions with R/sub n/=20-70 Omega at junction area 8/14 mu m/sup 2/. The best values of T/sub r/ (SSB) were measured to as low as 5 K on the mixer cold input flange in the 45-55-GHz bandwidth at an ambient temperature of 4.2 K. A mixer gain of up to 10 dB was obtained. The gain values were limited by bias stability at very high or even negative array output impedance. An experimental receiver noise temperature (SSB) of less than 20 K has been achieved.
We present measurements with a prototype waveguide SIS mixer for band 2 (640 GHz – 800 GHz) of HIFI (Heterodyne Instrument for FIRST). The Nb/Al2O3/Nb junctions have an RnA product from 12–18 Ωμm. These junctions are embedded in microstrip circuits tuning out the device capacitance using a NbTiN ground layer and various top conductor materials such as NbTiN, Nb and Al. The NbTiN films are fabricated by DC magnetron sputtering which is optimized for a minimum value of the DC resistivity and for a high critical temperature by varying the sputter pressure, sputter power and Ar:N2 flow. Typical NbTiN film parameters for device fabrication are ρ = 120 μΩcm and Tc = 14.5 K. The best uncorrected noise temperatures we measured so far are for devices with NbTiN/SiO2/Nb tuning. At 4.2 K bath temperature, a standard Yfactor measurement yields uncorrected receiver noise temperatures of 350 K at 642 GHz and 500 K at 810 GHz for 1.5 GHz intermediate frequency. We discuss the effect of the various tuning circuit materials on the mixer performance. In addition, measurements at IF’s between 4 GHz and 8 GHz will be presented.
At the Smithsonian Astrophysical Observatory, we have been developing expertise in the construction of high-frequency heterodyne receivers using SIS junctions as their first mixing elements. This research has been carried out in support of the Submillimeter Array (SMA), a radio interferometer soon to be built on Mauna Kea that will require multiple reciever systems at a number of bands between 177 GHz and 920 GHz. In this paper, we describe research on the fabrication of all-refractory SIS junctions. To be useful as high-frequency mixers, SIS junctions must have small area and high critical current density. At the lower SMA frequencies, Nb/Al-Oxide/Nb ahs proven to be an ideal material system, and optical photolithography has sufficient resolution for junction definition. At the higher frequencies, NbN/MgO/NbN may enjoy an advantage due to its larger energy gap, and electron-beam lithography may be necessary for defining junctions much smaller than one micron in size. We report good initial results for Nb/Al-Oxide/Nb junctions, fabricated using a self-aligned optical technique, with area $AP 0.5 micrometers 2 and critical current density $AP 10,000 Amp/cm2.
Apart from the great success of SIS-junctions as mixers in heterodyne receivers there are several other reasons to intensify investigations of SIS-junctions as direct detectors. These devices can be produced as single junctions and arrays for use. in waveguide systems or in planar antennas by standard lithographic techniques. Impedance matching structures and filter elements can be incorporated easily. Recent developments1,2 in junction technology show strong improvements of junction performance. Areas of 0.5μm2 and leakage currents as low as 50nA have been realized. Since the final sensitivity (NEP) of SIS-junctions as direct detectors is limited ultimately by the shot noise of the bias current (NEP∼√IL), a low leakage current IL, is highly important for these devices. Using these improved SIS-junctions, NEP's down to 10-17W/√Hz seem to be possible with He4-cooled devices. A crude estimate for the time constant of a SIS-direct detector yields the inverse of the gap frequency h/∆ or the sumgap frequency h/2∆, which gives very small values of 1 − 10psec.
The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>