Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Magnetics

Parallel biased SIS-arrays for mm wave mixers: main ideas and experimental verification

An. B. Ermakov, V. P. Koshelets, Sergey Kovtonyuk, S. V. Shitov

Published Mar 1, 1991• 19 citations
Publisher

Abstract

The possibility of overcoming the main drawbacks of the traditional series arrays by parallel connection of the SIS (superconductor-insulator-superconductor) junctions for DC and IF are demonstrated experimentally. The proposed mixing elements avoid the influence of the junction nonuniformity in the array, provide the optimal matching on both RF input and IF output, and tune out junction capacitance. Experimentally tested arrays contained up to eight high-quality Nb-AlO/sub x/-Nb junctions with R/sub n/=20-70 Omega at junction area 8/14 mu m/sup 2/. The best values of T/sub r/ (SSB) were measured to as low as 5 K on the mixer cold input flange in the 45-55-GHz bandwidth at an ambient temperature of 4.2 K. A mixer gain of up to 10 dB was obtained. The gain values were limited by bias stability at very high or even negative array output impedance. An experimental receiver noise temperature (SSB) of less than 20 K has been achieved.

DOI
10.1109/20.133754

Related papers

Ultra-low-noise 100 GHz receiver based on parallel biased SIS arrays

S. V. Shitov, V. P. Koshelets, Sergey Kovtonyuk +3 more

The possibility of overcoming the main drawbacks of the traditional series arrays by using a parallel connection of SIS junctions for DC and IF current has been experimentally demonstrated in full height 70-116 GHz waveguide mixers. This new array concept has been successfully developed to: (i) avoid the influence of junction non-uniformity in the array; (ii) provide optimal matching at both RF input and IF output even in the case of high gain, and (iii) tune out junction capacitance without any DC blocks. The experimentally tested arrays contain 10 or 11 trilayer 2.5 mu m 2 Nb-AlO x -Nb junctions. Best values of T r (DSB) as low as 20+or-2 K have been measured at the receiver room temperature horn in the 104-108 GHz LO range with a 4 GHz IF and at a mixer ambient temperature of 4.5-5.5 K. An SSB mixer noise temperature as low as 6+or-3 K was estimated. This value is very close to the quantum noise limit hf/k approximately=5 K.

Superconductor Science and Technology•Sep 1, 1991•14 citations

Perfectly matched SIS arrays for mm wave receivers

S. V. Shitov, V. P. Koshelets, Sergey Kovtonyuk +1 more

A novel conception of improved matching for both input and output mixer ports has been developed and confirmed successfully with experimental receivers in the 40-180-GHz frequency range. Parallel and parallel-series combinations integrated up to 11 Nb-AlO/sub x/-Nb type superconductor-insulator-superconductor (SIS) junctions have been tested in full-height waveguide mixers. Receivers' noise temperatures T/sub r/(DSB)>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•2 citations

Performance of a two-junction array SIS-mixer operating around 345 GHz

Cornelia E. Honingh, Gert J. de Lange, M. M. T. M. Dierichs +3 more

The authors have made a detailed study of the gain and noise of a SIS (superconductor-insulator-superconductor) heterodyne receiver at 345 GHz. An array of two Nb-Al/sub 2/O/sub 3/-Nb SIS junctions in series are used as the mixing element. The array is operated in a waveguide mount with a backshort and an E-plane tuner. The best receiver noise temperature achieved is 140 K DSB (double sideband). The embedding impedances were determined by fitting theory to the measured pumped curves. High-quality fits were obtained, providing the first detailed test of the Tucker-theory at frequencies above 300 GHz. The impedances found by this method are in very good agreement with impedances measured in a scale model at 3.3 GHz. From these embedding impedances, the gain and noise of the mixer were calculated over a full bias range using the Tucker theory in the three-port low-IF approximation. The measured dependence of mixer gain and noise on bias voltage, pump power and embedding impedance is in good agreement with theory. However the absolute values show discrepancies that appear to be independent of the bias parameters of the mixer.>

IEEE Transactions on Microwave Theory and Techniques•Apr 1, 1993•14 citations

MM wave quasioptical SIS mixers

Qing Hu, C. A. Mears, P. L. Richards +1 more

The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>

IEEE Transactions on Magnetics•Mar 1, 1989•32 citations

SNAP structures with Nb-AlO/sub x/-Nb junctions for MM-wave receivers

An. B. Ermakov, V. P. Koshelets, I. L. Serpuchenko +3 more

High-quality small-area Nb-AlO/sub x/-Nb junctions have been fabricated by the selective niobium anodization process (SNAP). The influence of the preparation conditions on the junction properties were investigated. Numerical calculations based on I-V (current-voltage) characteristics measured by a data acquisition system were used to simulate the mixer performance. It has been shown that the knee-shaped structure on the I-V curve of refractory material junctions significantly affects the signal properties of the mixer. The signal and noise properties for different types of integrated SIS (superconductor-insulator-superconductor) mixing elements have been investigated experimentally in the frequency range of 37-53 GHz; the mixer conversion loss was as low as 4 dB at 45 GHz. The mixing elements consist of an odd number of SIS junctions connected in series for RF and in parallel for DC biasing. The DC bias wiring and IF (intermediate frequency) filters of these structures were designed to provide tuning out of junction capacitance and thin-film-electrode inductance.>

IEEE Transactions on Magnetics•Mar 1, 1989•7 citations

An SIS mixer using two junctions connected in parallel

Takashi Noguchi, Sheng‐Cai Shi, Junji Inatani

We have fabricated a superconductor-insulator-superconductor (SIS) mixer using a couple of junctions connected in parallel through a stripline inductor. The junctions have significantly larger area, i.e. larger capacitance, and smaller normal resistance than conventional ones. In order to obtain a good impedance matching between the source and the junctions, an impedance transformer made of a superconducting stripline was integrated with the junctions. The capacitance of the junctions was tuned out by the inductor to obtain a broadband operation without mechanical tuning elements. It was shown that the double sideband noise temperature of the receiver employing this type of mixer device was less than 40 K over the bandwidth of 90-115 GHz. The lowest receiver noise temperature of /spl sim/20 K, which is only 4 times as large as the quantum limited photon noise of hv/k/sub B/, was obtained around 105 GHz.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•41 citations
The possibility of overcoming the main drawbacks of the traditional series arrays by parallel connection of the SIS (superconductor-insulator-superconductor) junctions for DC and IF are demonstrated experimentally. The proposed mixing elements avoid the influence of the junction nonuniformity in the array, provide the optimal matching on both RF input and IF output, and tune out junction capacitance. Experimentally tested arrays contained up to eight high-quality Nb-AlO/sub x/-Nb junctions with R/sub n/=20-70 Omega at junction area 8/14 mu m/sup 2/. The best values of T/sub r/ (SSB) were measured to as low as 5 K on the mixer cold input flange in the 45-55-GHz bandwidth at an ambient temperature of 4.2 K. A mixer gain of up to 10 dB was obtained. The gain values were limited by bias stability at very high or even negative array output impedance. An experimental receiver noise temperature (SSB) of less than 20 K has been achieved.
The possibility of overcoming the main drawbacks of the traditional series arrays by using a parallel connection of SIS junctions for DC and IF current has been experimentally demonstrated in full height 70-116 GHz waveguide mixers. This new array concept has been successfully developed to: (i) avoid the influence of junction non-uniformity in the array; (ii) provide optimal matching at both RF input and IF output even in the case of high gain, and (iii) tune out junction capacitance without any DC blocks. The experimentally tested arrays contain 10 or 11 trilayer 2.5 mu m 2 Nb-AlO x -Nb junctions. Best values of T r (DSB) as low as 20+or-2 K have been measured at the receiver room temperature horn in the 104-108 GHz LO range with a 4 GHz IF and at a mixer ambient temperature of 4.5-5.5 K. An SSB mixer noise temperature as low as 6+or-3 K was estimated. This value is very close to the quantum noise limit hf/k approximately=5 K.
The authors have made a detailed study of the gain and noise of a SIS (superconductor-insulator-superconductor) heterodyne receiver at 345 GHz. An array of two Nb-Al/sub 2/O/sub 3/-Nb SIS junctions in series are used as the mixing element. The array is operated in a waveguide mount with a backshort and an E-plane tuner. The best receiver noise temperature achieved is 140 K DSB (double sideband). The embedding impedances were determined by fitting theory to the measured pumped curves. High-quality fits were obtained, providing the first detailed test of the Tucker-theory at frequencies above 300 GHz. The impedances found by this method are in very good agreement with impedances measured in a scale model at 3.3 GHz. From these embedding impedances, the gain and noise of the mixer were calculated over a full bias range using the Tucker theory in the three-port low-IF approximation. The measured dependence of mixer gain and noise on bias voltage, pump power and embedding impedance is in good agreement with theory. However the absolute values show discrepancies that appear to be independent of the bias parameters of the mixer.>
The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>
High-quality small-area Nb-AlO/sub x/-Nb junctions have been fabricated by the selective niobium anodization process (SNAP). The influence of the preparation conditions on the junction properties were investigated. Numerical calculations based on I-V (current-voltage) characteristics measured by a data acquisition system were used to simulate the mixer performance. It has been shown that the knee-shaped structure on the I-V curve of refractory material junctions significantly affects the signal properties of the mixer. The signal and noise properties for different types of integrated SIS (superconductor-insulator-superconductor) mixing elements have been investigated experimentally in the frequency range of 37-53 GHz; the mixer conversion loss was as low as 4 dB at 45 GHz. The mixing elements consist of an odd number of SIS junctions connected in series for RF and in parallel for DC biasing. The DC bias wiring and IF (intermediate frequency) filters of these structures were designed to provide tuning out of junction capacitance and thin-film-electrode inductance.>
We have fabricated a superconductor-insulator-superconductor (SIS) mixer using a couple of junctions connected in parallel through a stripline inductor. The junctions have significantly larger area, i.e. larger capacitance, and smaller normal resistance than conventional ones. In order to obtain a good impedance matching between the source and the junctions, an impedance transformer made of a superconducting stripline was integrated with the junctions. The capacitance of the junctions was tuned out by the inductor to obtain a broadband operation without mechanical tuning elements. It was shown that the double sideband noise temperature of the receiver employing this type of mixer device was less than 40 K over the bandwidth of 90-115 GHz. The lowest receiver noise temperature of /spl sim/20 K, which is only 4 times as large as the quantum limited photon noise of hv/k/sub B/, was obtained around 105 GHz.>