Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Magnetics

SNAP structures with Nb-AlO/sub x/-Nb junctions for MM-wave receivers

An. B. Ermakov, V. P. Koshelets, I. L. Serpuchenko, Lyudmila V. Filippenko, S. V. Shitov, Alexander N. Vystavkin

Published Mar 1, 1989• 7 citations
Publisher

Abstract

High-quality small-area Nb-AlO/sub x/-Nb junctions have been fabricated by the selective niobium anodization process (SNAP). The influence of the preparation conditions on the junction properties were investigated. Numerical calculations based on I-V (current-voltage) characteristics measured by a data acquisition system were used to simulate the mixer performance. It has been shown that the knee-shaped structure on the I-V curve of refractory material junctions significantly affects the signal properties of the mixer. The signal and noise properties for different types of integrated SIS (superconductor-insulator-superconductor) mixing elements have been investigated experimentally in the frequency range of 37-53 GHz; the mixer conversion loss was as low as 4 dB at 45 GHz. The mixing elements consist of an odd number of SIS junctions connected in series for RF and in parallel for DC biasing. The DC bias wiring and IF (intermediate frequency) filters of these structures were designed to provide tuning out of junction capacitance and thin-film-electrode inductance.>

DOI
10.1109/20.92471

Related papers

Parallel biased SIS-arrays for mm wave mixers: main ideas and experimental verification

An. B. Ermakov, V. P. Koshelets, Sergey Kovtonyuk +1 more

The possibility of overcoming the main drawbacks of the traditional series arrays by parallel connection of the SIS (superconductor-insulator-superconductor) junctions for DC and IF are demonstrated experimentally. The proposed mixing elements avoid the influence of the junction nonuniformity in the array, provide the optimal matching on both RF input and IF output, and tune out junction capacitance. Experimentally tested arrays contained up to eight high-quality Nb-AlO/sub x/-Nb junctions with R/sub n/=20-70 Omega at junction area 8/14 mu m/sup 2/. The best values of T/sub r/ (SSB) were measured to as low as 5 K on the mixer cold input flange in the 45-55-GHz bandwidth at an ambient temperature of 4.2 K. A mixer gain of up to 10 dB was obtained. The gain values were limited by bias stability at very high or even negative array output impedance. An experimental receiver noise temperature (SSB) of less than 20 K has been achieved.

IEEE Transactions on Magnetics•Mar 1, 1991•19 citations

Fabrication of Nb/Al-N/sub x//NbTiN junctions for SIS mixer applications

B. Bumble, Henry George LeDuc, Jeff A. Stern +1 more

We discuss fabrication and characteristics of superconductor-insulator-superconductor (SIS) junctions which typically exhibit a 3.5 mV sum-gap voltage. Junctions have a sub-gap to normal state resistance ratio of R/sub SG//R/sub N/=27 for resistance-area products down to R/sub N/A=8 /spl Omega/ /spl mu/m/sup 2/ and high quality junctions have been produced with RNA products as low as 4 /spl Omega/ /spl mu/m/sup 2/. The device structure incorporates a Nb base electrode, a tunnel barrier formed by plasma nitridation of a thin Al proximity layer, and a NbTiN counter-electrode. Results for all Nb junctions with high current density aluminum-nitride barriers are also shown. Nitridation of the aluminum layer is investigated by control of the dc floating potential on a separate rf driven electrode in the vacuum process chamber. Devices are integrated to a mixer antenna structure incorporating NbTiN as a ground plane. The wire circuit layer can be either normal metal or NbTiN. Annealing results show improved I-V characteristics with increased RNA products. Recent receiver measurements employing these junctions exhibit low noise performance up to 900 GHz.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•53 citations

Refractory material SIS junction structures

Victor Y. Belitsky, V. Gubankov, V. P. Koshelets +5 more

Niobium based SIS junction structures for microwave receiving devices were investigated. The possibility of the mixing efficiency improving for Nb-Al2O3-Nb junctions with a negative resistance on I-V curve near the gap voltage has been demonstrated. Comparative microwave investigation of the parallel and series DC biased arrays shows the advantage of the first one. SIS junction capacitance has been compensated with microstrip or lumped elements at the signal frequency. Such compensated structures were investigated at frequencies 38 and 76 GHz both in waveguide and quasioptic systems.

IEEE Transactions on Magnetics•Mar 1, 1987•5 citations

MM wave quasioptical SIS mixers

Qing Hu, C. A. Mears, P. L. Richards +1 more

The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>

IEEE Transactions on Magnetics•Mar 1, 1989•32 citations

Superconducting millimeter wave oscillators and SIS mixers integrated on a chip

V. P. Koshelets, А. В. Щукин, S. V. Shitov +1 more

All-refractory material superconducting millimeter-wave oscillators have been designed and investigated experimentally with different superconductor-insulator-superconductor (SIS) mixers integrated on the same chip. Tested structures include a flux-flow oscillator (FFO) based on a long Josephson junction, a coupling section, and an SIS detector with tuned out junction capacitance. Coupling sections were designed as multistep microstrip quarter-wave impedance transformers. All junctions have been fabricated on the basis of a high-quality trilayer Nb-AlO/sub x/-Nb process. Microwave oscillations in the frequency range 75-500 GHz have been detected experimentally. The level of delivered power was estimated from the pumped I-V curve of the strongly coupled single junction detector. Coupled power levels higher than 0.1 mu W at 256 GHz were achieved. A spectral linewidth of the FFO of less than 1 MHz has been estimated experimentally. The first attempt to create an integrated receiver based on an FFO and an SIS array mixer integrated on the same chip was made in the 2-mm wavelength band.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•65 citations

High-quality sub-micron Nb trilayer tunnel junctions for a 100 GHz SIS receiver

A. Hodge Worsham, D. E. Prober, J.H. Kang +2 more

A modified SNIP process was used to fabricate high-quality 0.5, 2, and 4 mu m/sup 2/ small-area Nb/AlO/sub x//Nb trilayer tunnel junctions with current densities as large as 5000 A/cm/sup 2/. The average junction quality factors for the junctions at 4.4 K were V/sub m/(2 mV)=39 mV for J/sub c/=3000 A/cm/sup 2/ and V/sub m/ (2 mV)=27 mV for J/sub c/=5000 A/cm/sup 2/. The best values of V/sub m/ obtained were 50 mV for J/sub c/=3000 A/cm/sup 2/ and 41 mV for J/sub c/=5000 A/cm/sup 2/. These devices were designed and fabricated for use in a W-band mixer receiver. The substrate was 50- mu m-thick fused or crystal quartz. Special methods were developed for handling such thin insulating substrates and patterning films. The fabrication process was self-aligned and used SiO/sub 2/ instead of anodized Nb as the thick insulator. SiO/sub 2/ isolated the junction area and defined the opening for contact to the Nb wiring layer. The authors have fabricated series arrays of up to 12 junctions, with individual junction areas of 0.5 mu m/sup 2/. The array I-V quality was not degraded compared to that of an individual junction.

IEEE Transactions on Magnetics•Mar 1, 1991•16 citations
High-quality small-area Nb-AlO/sub x/-Nb junctions have been fabricated by the selective niobium anodization process (SNAP). The influence of the preparation conditions on the junction properties were investigated. Numerical calculations based on I-V (current-voltage) characteristics measured by a data acquisition system were used to simulate the mixer performance. It has been shown that the knee-shaped structure on the I-V curve of refractory material junctions significantly affects the signal properties of the mixer. The signal and noise properties for different types of integrated SIS (superconductor-insulator-superconductor) mixing elements have been investigated experimentally in the frequency range of 37-53 GHz; the mixer conversion loss was as low as 4 dB at 45 GHz. The mixing elements consist of an odd number of SIS junctions connected in series for RF and in parallel for DC biasing. The DC bias wiring and IF (intermediate frequency) filters of these structures were designed to provide tuning out of junction capacitance and thin-film-electrode inductance.>
The possibility of overcoming the main drawbacks of the traditional series arrays by parallel connection of the SIS (superconductor-insulator-superconductor) junctions for DC and IF are demonstrated experimentally. The proposed mixing elements avoid the influence of the junction nonuniformity in the array, provide the optimal matching on both RF input and IF output, and tune out junction capacitance. Experimentally tested arrays contained up to eight high-quality Nb-AlO/sub x/-Nb junctions with R/sub n/=20-70 Omega at junction area 8/14 mu m/sup 2/. The best values of T/sub r/ (SSB) were measured to as low as 5 K on the mixer cold input flange in the 45-55-GHz bandwidth at an ambient temperature of 4.2 K. A mixer gain of up to 10 dB was obtained. The gain values were limited by bias stability at very high or even negative array output impedance. An experimental receiver noise temperature (SSB) of less than 20 K has been achieved.
We discuss fabrication and characteristics of superconductor-insulator-superconductor (SIS) junctions which typically exhibit a 3.5 mV sum-gap voltage. Junctions have a sub-gap to normal state resistance ratio of R/sub SG//R/sub N/=27 for resistance-area products down to R/sub N/A=8 /spl Omega/ /spl mu/m/sup 2/ and high quality junctions have been produced with RNA products as low as 4 /spl Omega/ /spl mu/m/sup 2/. The device structure incorporates a Nb base electrode, a tunnel barrier formed by plasma nitridation of a thin Al proximity layer, and a NbTiN counter-electrode. Results for all Nb junctions with high current density aluminum-nitride barriers are also shown. Nitridation of the aluminum layer is investigated by control of the dc floating potential on a separate rf driven electrode in the vacuum process chamber. Devices are integrated to a mixer antenna structure incorporating NbTiN as a ground plane. The wire circuit layer can be either normal metal or NbTiN. Annealing results show improved I-V characteristics with increased RNA products. Recent receiver measurements employing these junctions exhibit low noise performance up to 900 GHz.
Niobium based SIS junction structures for microwave receiving devices were investigated. The possibility of the mixing efficiency improving for Nb-Al2O3-Nb junctions with a negative resistance on I-V curve near the gap voltage has been demonstrated. Comparative microwave investigation of the parallel and series DC biased arrays shows the advantage of the first one. SIS junction capacitance has been compensated with microstrip or lumped elements at the signal frequency. Such compensated structures were investigated at frequencies 38 and 76 GHz both in waveguide and quasioptic systems.
The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>
All-refractory material superconducting millimeter-wave oscillators have been designed and investigated experimentally with different superconductor-insulator-superconductor (SIS) mixers integrated on the same chip. Tested structures include a flux-flow oscillator (FFO) based on a long Josephson junction, a coupling section, and an SIS detector with tuned out junction capacitance. Coupling sections were designed as multistep microstrip quarter-wave impedance transformers. All junctions have been fabricated on the basis of a high-quality trilayer Nb-AlO/sub x/-Nb process. Microwave oscillations in the frequency range 75-500 GHz have been detected experimentally. The level of delivered power was estimated from the pumped I-V curve of the strongly coupled single junction detector. Coupled power levels higher than 0.1 mu W at 256 GHz were achieved. A spectral linewidth of the FFO of less than 1 MHz has been estimated experimentally. The first attempt to create an integrated receiver based on an FFO and an SIS array mixer integrated on the same chip was made in the 2-mm wavelength band.>
A modified SNIP process was used to fabricate high-quality 0.5, 2, and 4 mu m/sup 2/ small-area Nb/AlO/sub x//Nb trilayer tunnel junctions with current densities as large as 5000 A/cm/sup 2/. The average junction quality factors for the junctions at 4.4 K were V/sub m/(2 mV)=39 mV for J/sub c/=3000 A/cm/sup 2/ and V/sub m/ (2 mV)=27 mV for J/sub c/=5000 A/cm/sup 2/. The best values of V/sub m/ obtained were 50 mV for J/sub c/=3000 A/cm/sup 2/ and 41 mV for J/sub c/=5000 A/cm/sup 2/. These devices were designed and fabricated for use in a W-band mixer receiver. The substrate was 50- mu m-thick fused or crystal quartz. Special methods were developed for handling such thin insulating substrates and patterning films. The fabrication process was self-aligned and used SiO/sub 2/ instead of anodized Nb as the thick insulator. SiO/sub 2/ isolated the junction area and defined the opening for contact to the Nb wiring layer. The authors have fabricated series arrays of up to 12 junctions, with individual junction areas of 0.5 mu m/sup 2/. The array I-V quality was not degraded compared to that of an individual junction.