Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

High-current-density small-area SIS junctions for high-frequency radio astronomy

Eric E. Bloemhof

Published Jul 2, 1994• 1 citation
Publisher

Abstract

At the Smithsonian Astrophysical Observatory, we have been developing expertise in the construction of high-frequency heterodyne receivers using SIS junctions as their first mixing elements. This research has been carried out in support of the Submillimeter Array (SMA), a radio interferometer soon to be built on Mauna Kea that will require multiple reciever systems at a number of bands between 177 GHz and 920 GHz. In this paper, we describe research on the fabrication of all-refractory SIS junctions. To be useful as high-frequency mixers, SIS junctions must have small area and high critical current density. At the lower SMA frequencies, Nb/Al-Oxide/Nb ahs proven to be an ideal material system, and optical photolithography has sufficient resolution for junction definition. At the higher frequencies, NbN/MgO/NbN may enjoy an advantage due to its larger energy gap, and electron-beam lithography may be necessary for defining junctions much smaller than one micron in size. We report good initial results for Nb/Al-Oxide/Nb junctions, fabricated using a self-aligned optical technique, with area $AP 0.5 micrometers 2 and critical current density $AP 10,000 Amp/cm2.

DOI
10.1117/12.180990

Related papers

Fabrication and characterization of high current-density, submicron, NbN/MgO/NbN tunnel junctions

Jeff A. Stern, Henry George LeDuc, A. Judas

At near-millimeter wavelengths, heterodyne receivers based on SIS tunnel junctions are the most sensitive available. However, in order to scale these results to submillimeter wavelengths, certain device properties should be scaled. The tunnel-junction's current density should be increased to reduce the RC product. The device's area should be reduced to efficiently couple power from the antenna to the mixer. Finally, the superconductor used should have a large energy gap to minimize RF losses. Most SIS mixers use Nb or Pb-alloy tunnel junctions; the gap frequency for these materials is approximately 725 GHz. Above the gap frequency, these materials exhibit losses similar to those in a normal metal. The gap frequency in NbN films is as-large-as 1440 GHz. Therefore, we have developed a process to fabricate small area (down to 0.13 sq microns), high current density, NbN/MgO/NbN tunnel junctions.

•Jan 1, 1992•11 citations

Submillimeter mixers based on superconductive parallel junction arrays

Faouzi M. Boussaha, Morvan C. Salez, Y. Delorme +4 more

Observation and analysis of submillimeter-wave radiation (300GHz-3THz) in astronomy and atmospheric sciences requires increasingly performant receivers. The most sensitive receivers working in this range of electromagnetic spectrum use superconductor-insolator-superconductor (SIS) junctions. In order to increase the bandwidth and the sensitivity, we are developing a quantum-noise limited heterodyne receiver based on several parallel SIS junctions with broad (larger than 30%) fixed tuned bandwidth. These circuits can be viewed as passband filters which have been optimized by varying the spacings between junctions. We have designed such 5-junction arrays for operation in the range 480-640 GHz. Fabrication and heterodyne characterization of these devices has been done. The 1 μm2 junctions current density ranges from 4 to 13 kA/cm2, using optical lithography and Nb/Al2Nb5/Nb trilayer sputtering technology. The fabrication process and yield are presented in this paper, along with measured performances

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 25, 2003•1 citation

Submicron area NbN/MgO/NbN tunnel junctions for SIS mixer applications

Henry George LeDuc, A. Judas, S.R. Cypher +3 more

The development of submicron area mixer elements for operation in the submillimeter wave range is discussed. High-current-density NbN/MgO/NbN tunnel junctions with areas down to 0.1 mu m/sup 2/ have been fabricated in both planar and edge geometries. The planar junctions were fabricated from in situ deposited trilayers using electron-beam lithography to pattern submicron area mesas. Modifications of fabrication techniques used in larger-area NbN tunnel junctions are required and are discussed. The NbN/MgO/NbN edge junction process using sapphire substrates has been transferred to technologically important quartz substrates using MgO buffer layers to minimize substrate interactions. The two junction geometries are compared and contrasted in the context of submillimeter wave mixer applications.

IEEE Transactions on Magnetics•Mar 1, 1991•22 citations

Superconducting detectors for submillimeter-wave astronomy

Eric E. Bloemhof

Sensitive heterodyne receivers are being built at ever higher frequencies with superconducting (SIS) junctions as the first mixer. These devices have extremely sharp non-linearities in their current-voltage characteristics as a result of quantum-mechanical tunneling of electrons across thin insulating barriers. The low energy scale set by the magnitude of the superconducting energy gap implies very low local oscillator power requirements for heterodyne operation. Some general system design considerations for astrophysical receivers are reviewed. These principles are illustrated by discussing two specific applications: a 230 GHz SIS receiver recently installed as a facility instrument at the Swedish-ESO submillimeter telescope in Chile, and the broader receiver requirements of the 6-antenna submillimeter array (SMA), an interferometer now being designed at the Harvard-Smithsonian Center for Astrophysics. The SMA will require receivers at frequencies as high as 820 GHz, and will place some unique demands on detector performance.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jul 15, 1993•0 citations

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology

Jing Li, Masanori Takeda, Zhen Wang +1 more

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 29, 2007•3 citations

SIS Junctions for Millimeter and Submillimeter Wave Mixers

Takashi Noguchi, Toyoaki Suzuki, Tomonori Tamura

We have developed a process for the fabrication of high-quality Nb/AlOx/Nb tunnel junctions with small area and high current densities for the heterodyne mixers at millimeter and submillimeter wavelengths. Their dc I-V curves are numerically studied, including the broadening of quasiparticle density of states resulting from the existence of an imaginary part of the gap energy of Nb. We have found both experimentally and numerically that the subgap current is strongly dependent on bias voltage at temperatures below 4.2K unlike the prediction of the BCS tunneling theory. It is shown that calculated dc I-V curves taking into account the complex number of the gap energy agree well with those of Nb/AlOx/Nb junctions measured at temperatures from 0.4 to 4.2K. We have successfully built receivers at millimeter and submillimeter wavelengths with the noise temperature as low as 4 times the quantum photon noise, employing those high-quality Nb/AlOx/Nb junctions. Those low-noise receivers are to be installed in the ALMA (Atacama Large Millimeter/Submillimeter Array) telescope and they are going into series production now.

IEICE Transactions on Electronics•Jan 1, 2012•2 citations
At the Smithsonian Astrophysical Observatory, we have been developing expertise in the construction of high-frequency heterodyne receivers using SIS junctions as their first mixing elements. This research has been carried out in support of the Submillimeter Array (SMA), a radio interferometer soon to be built on Mauna Kea that will require multiple reciever systems at a number of bands between 177 GHz and 920 GHz. In this paper, we describe research on the fabrication of all-refractory SIS junctions. To be useful as high-frequency mixers, SIS junctions must have small area and high critical current density. At the lower SMA frequencies, Nb/Al-Oxide/Nb ahs proven to be an ideal material system, and optical photolithography has sufficient resolution for junction definition. At the higher frequencies, NbN/MgO/NbN may enjoy an advantage due to its larger energy gap, and electron-beam lithography may be necessary for defining junctions much smaller than one micron in size. We report good initial results for Nb/Al-Oxide/Nb junctions, fabricated using a self-aligned optical technique, with area AP0.5micrometers2andcriticalcurrentdensityAP 0.5 micrometers 2 and critical current density AP0.5micrometers2andcriticalcurrentdensityAP 10,000 Amp/cm2.
At near-millimeter wavelengths, heterodyne receivers based on SIS tunnel junctions are the most sensitive available. However, in order to scale these results to submillimeter wavelengths, certain device properties should be scaled. The tunnel-junction's current density should be increased to reduce the RC product. The device's area should be reduced to efficiently couple power from the antenna to the mixer. Finally, the superconductor used should have a large energy gap to minimize RF losses. Most SIS mixers use Nb or Pb-alloy tunnel junctions; the gap frequency for these materials is approximately 725 GHz. Above the gap frequency, these materials exhibit losses similar to those in a normal metal. The gap frequency in NbN films is as-large-as 1440 GHz. Therefore, we have developed a process to fabricate small area (down to 0.13 sq microns), high current density, NbN/MgO/NbN tunnel junctions.
Observation and analysis of submillimeter-wave radiation (300GHz-3THz) in astronomy and atmospheric sciences requires increasingly performant receivers. The most sensitive receivers working in this range of electromagnetic spectrum use superconductor-insolator-superconductor (SIS) junctions. In order to increase the bandwidth and the sensitivity, we are developing a quantum-noise limited heterodyne receiver based on several parallel SIS junctions with broad (larger than 30%) fixed tuned bandwidth. These circuits can be viewed as passband filters which have been optimized by varying the spacings between junctions. We have designed such 5-junction arrays for operation in the range 480-640 GHz. Fabrication and heterodyne characterization of these devices has been done. The 1 μm2 junctions current density ranges from 4 to 13 kA/cm2, using optical lithography and Nb/Al2Nb5/Nb trilayer sputtering technology. The fabrication process and yield are presented in this paper, along with measured performances
The development of submicron area mixer elements for operation in the submillimeter wave range is discussed. High-current-density NbN/MgO/NbN tunnel junctions with areas down to 0.1 mu m/sup 2/ have been fabricated in both planar and edge geometries. The planar junctions were fabricated from in situ deposited trilayers using electron-beam lithography to pattern submicron area mesas. Modifications of fabrication techniques used in larger-area NbN tunnel junctions are required and are discussed. The NbN/MgO/NbN edge junction process using sapphire substrates has been transferred to technologically important quartz substrates using MgO buffer layers to minimize substrate interactions. The two junction geometries are compared and contrasted in the context of submillimeter wave mixer applications.
Sensitive heterodyne receivers are being built at ever higher frequencies with superconducting (SIS) junctions as the first mixer. These devices have extremely sharp non-linearities in their current-voltage characteristics as a result of quantum-mechanical tunneling of electrons across thin insulating barriers. The low energy scale set by the magnitude of the superconducting energy gap implies very low local oscillator power requirements for heterodyne operation. Some general system design considerations for astrophysical receivers are reviewed. These principles are illustrated by discussing two specific applications: a 230 GHz SIS receiver recently installed as a facility instrument at the Swedish-ESO submillimeter telescope in Chile, and the broader receiver requirements of the 6-antenna submillimeter array (SMA), an interferometer now being designed at the Harvard-Smithsonian Center for Astrophysics. The SMA will require receivers at frequencies as high as 820 GHz, and will place some unique demands on detector performance.
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.
We have developed a process for the fabrication of high-quality Nb/AlOx/Nb tunnel junctions with small area and high current densities for the heterodyne mixers at millimeter and submillimeter wavelengths. Their dc I-V curves are numerically studied, including the broadening of quasiparticle density of states resulting from the existence of an imaginary part of the gap energy of Nb. We have found both experimentally and numerically that the subgap current is strongly dependent on bias voltage at temperatures below 4.2K unlike the prediction of the BCS tunneling theory. It is shown that calculated dc I-V curves taking into account the complex number of the gap energy agree well with those of Nb/AlOx/Nb junctions measured at temperatures from 0.4 to 4.2K. We have successfully built receivers at millimeter and submillimeter wavelengths with the noise temperature as low as 4 times the quantum photon noise, employing those high-quality Nb/AlOx/Nb junctions. Those low-noise receivers are to be installed in the ALMA (Atacama Large Millimeter/Submillimeter Array) telescope and they are going into series production now.