Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Microwave Theory and Techniques

A Low-Noise 47-GHz Mixer Using a Permanent Josephson Junction

JOCHEN EDRICH

Published Nov 1, 1976• 7 citations
Publisher

Abstract

A new method to produce permanent Josephson junctions for millimeter-wave mixers is reported. In contrast to conventional point contacts which are mechanically unstable and require adjustments after each cooldown, these point contact junctions are set at room temperature, stay mechanically stable, and can be temperature cycled without readjustments. Using these junctions in a modified Sharpless wafer mixer mount, a single-sideband noise temperature of 71 K was measured at 47 GHz. Based on these results, system noise temperatures of less than 100 K are predicted for practical broad-band radiometers, RADAR, and communications receivers up to at least 100 GHz

DOI
10.1109/tmtt.1976.1128948

Related papers

Low-noise Josephson mixers at 115 GHz using recyclable point contacts

Y. Taur, Anthony R. Kerr

Thermally recyclable Nb point-contact Josephson junctions are investigated as low-noise mixers with an external local oscillator at 115 GHz. The best single sideband mixer noise temperature achieved is 140 (±20) K with a (SSB) conversion loss of 2.4 (±0.5) dB. Such rugged junctions are suitable for use in practical receivers and should give unprecedented sensitivity at the shorter millimeter wavelengths.

Applied Physics Letters•Jun 1, 1978•32 citations

Progress on millimeter wave Josephson junction mixers

Y. Taur, Anthony R. Kerr

Preset, recyclable Nb point contacts are tested as low‐noise Josephson mixers at a signal frequency of 115 GHz. The best result achieved is a mixer noise temperature (single sideband) of 120 K with unity conversion efficiency (SSB) for a junction at 6 K. Variation of mixer properties with temperature and other parameters is presented.

AIP conference proceedings•Jan 1, 1978•1 citation

Noise in Josephson effect mm-wave mixers

J. H. Claassen, Y. Taur, P. L. Richards

We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.

IEEE Transactions on Magnetics•Mar 1, 1975•1 citation

Josephson junction mm-wave mixer without matching structure

Qi Cheng, Sen Yang, Yan Sheng

This paper describes a Josephson junction mixer at 8-mm wavelength without matching structure. With a Nb point contact operating at 4.2 K, a single-sideband mixer noise temperature T/sub M/approx.100 K and a conversion efficiency etaapprox.0.8 were measured by the Y-factor method of hot/cold noise. The mechanism of the mixing noise is also discussed.

Chin. Phys.; (United States)•Apr 1, 1982•0 citations

The properties of a heterodyne receiver at 450 GHz using a Josephson point-contact mixer and an external local oscillator

T. G. Blaney, N R Cross, Robert G. Jones

Adjustable niobium Josephson point contacts, mounted in fundamental-mode waveguide cavities, have been used as mixers in an experimental heterodyne receiver with a 450 GHz laser as the local oscillator. It was possible to estimate separately the various factors, such as intrinsic mixer conversion efficiency, mixer noise, and input coupling efficiency that contribute to the overall receiver sensitivity. Mixer performance agreed reasonably well with qualitative predictions of resistively-shunted-junction theoretical models, and there was broad quantitative agreement for some aspects of performance. Spurious, and potentially very misleading non-heterodyne responses to thermal signals were observed under some regimes of applied DC bias and local oscillator power. The lowest overall receiver noise temperature measured was 2100K (double side band), although reduction to 1000K should be possible with quite simple improvements. The intrinsic mixer noise temperatures were usually in the range 500-1000K (single side band), and local oscillator power required by the receiver was usually less than one microwatt. This performance makes these mixers competitive as the basis of very sensitive near-millimetre-wave receivers.

Journal of Physics D Applied Physics•Nov 14, 1982•12 citations

Point-contact Josephson mixers at 130 GHz

J. H. Claassen, P. L. Richards

The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.

Journal of Applied Physics•Jul 1, 1978•28 citations
A new method to produce permanent Josephson junctions for millimeter-wave mixers is reported. In contrast to conventional point contacts which are mechanically unstable and require adjustments after each cooldown, these point contact junctions are set at room temperature, stay mechanically stable, and can be temperature cycled without readjustments. Using these junctions in a modified Sharpless wafer mixer mount, a single-sideband noise temperature of 71 K was measured at 47 GHz. Based on these results, system noise temperatures of less than 100 K are predicted for practical broad-band radiometers, RADAR, and communications receivers up to at least 100 GHz
We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.
Adjustable niobium Josephson point contacts, mounted in fundamental-mode waveguide cavities, have been used as mixers in an experimental heterodyne receiver with a 450 GHz laser as the local oscillator. It was possible to estimate separately the various factors, such as intrinsic mixer conversion efficiency, mixer noise, and input coupling efficiency that contribute to the overall receiver sensitivity. Mixer performance agreed reasonably well with qualitative predictions of resistively-shunted-junction theoretical models, and there was broad quantitative agreement for some aspects of performance. Spurious, and potentially very misleading non-heterodyne responses to thermal signals were observed under some regimes of applied DC bias and local oscillator power. The lowest overall receiver noise temperature measured was 2100K (double side band), although reduction to 1000K should be possible with quite simple improvements. The intrinsic mixer noise temperatures were usually in the range 500-1000K (single side band), and local oscillator power required by the receiver was usually less than one microwatt. This performance makes these mixers competitive as the basis of very sensitive near-millimetre-wave receivers.
The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.