Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Chin. Phys.; (United States)

Josephson junction mm-wave mixer without matching structure

Qi Cheng, Sen Yang, Yan Sheng

Published Apr 1, 1982• 0 citations
OpenAlex

Abstract

This paper describes a Josephson junction mixer at 8-mm wavelength without matching structure. With a Nb point contact operating at 4.2 K, a single-sideband mixer noise temperature T/sub M/approx.100 K and a conversion efficiency etaapprox.0.8 were measured by the Y-factor method of hot/cold noise. The mechanism of the mixing noise is also discussed.

Related papers

Josephson-junction mm-wave mixer

В. А. Ильин, M. S. Kamenetskaia, T. M. Shurminova +1 more

The design of a mixer based on a Josephson point junction operating at lambda = 2 mm is described. A distinctive feature of the mixer is that it uses an intermediate microwave frequency (f/sub int/ = 10 GHz). The conversion losses referred to the contact are < or =12 dB and the noise temperature approx.180 K.

Soviet physics. Technical physics•Sep 1, 1982•0 citations

Noise in Josephson effect mm-wave mixers

J. H. Claassen, Y. Taur, P. L. Richards

We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.

IEEE Transactions on Magnetics•Mar 1, 1975•1 citation

Point-contact Josephson mixers at 130 GHz

J. H. Claassen, P. L. Richards

The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.

Journal of Applied Physics•Jul 1, 1978•28 citations

Progress on millimeter wave Josephson junction mixers

Y. Taur, Anthony R. Kerr

Preset, recyclable Nb point contacts are tested as low‐noise Josephson mixers at a signal frequency of 115 GHz. The best result achieved is a mixer noise temperature (single sideband) of 120 K with unity conversion efficiency (SSB) for a junction at 6 K. Variation of mixer properties with temperature and other parameters is presented.

AIP conference proceedings•Jan 1, 1978•1 citation

Low-noise Josephson mixers at 115 GHz using recyclable point contacts

Y. Taur, Anthony R. Kerr

Thermally recyclable Nb point-contact Josephson junctions are investigated as low-noise mixers with an external local oscillator at 115 GHz. The best single sideband mixer noise temperature achieved is 140 (±20) K with a (SSB) conversion loss of 2.4 (±0.5) dB. Such rugged junctions are suitable for use in practical receivers and should give unprecedented sensitivity at the shorter millimeter wavelengths.

Applied Physics Letters•Jun 1, 1978•32 citations

Josephson heterodyne detection at high thermal background levels

Tim Poorter

Point-contact Josephson junctions with a submicron contact diameter have been used as high-frequency mixers (170–220 GHz) under high thermal background conditions. The junction is formed across a full height (0.56×1.06 mm2) waveguide between a 3–5-μm thick Nb whisker and a 0.2-mm diam Nb center conductor of a coaxial line. The best single-side band mixer-noise temperature that was measured is 165 K (± 25%) with a corresponding single-side band conversion efficiency of 0.36±0.03 (a loss of 4.5 ±0.4 dB) at a signal frequency of 185 GHz, including losses in the coupling horn and the waveguide. The performance was measured with the hot-cold source technique. The effects of nonheterodyne response in that situation were investigated in detail. The junctions have been operated in a coherent receiver that can be used on a telescope with only small adaptations. The instantaneous bandwidth of the receiver is about 20 GHz.

Journal of Applied Physics•Jan 1, 1982•27 citations
This paper describes a Josephson junction mixer at 8-mm wavelength without matching structure. With a Nb point contact operating at 4.2 K, a single-sideband mixer noise temperature T/sub M/approx.100 K and a conversion efficiency etaapprox.0.8 were measured by the Y-factor method of hot/cold noise. The mechanism of the mixing noise is also discussed.
We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.
The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.
Point-contact Josephson junctions with a submicron contact diameter have been used as high-frequency mixers (170–220 GHz) under high thermal background conditions. The junction is formed across a full height (0.56×1.06 mm2) waveguide between a 3–5-μm thick Nb whisker and a 0.2-mm diam Nb center conductor of a coaxial line. The best single-side band mixer-noise temperature that was measured is 165 K (± 25%) with a corresponding single-side band conversion efficiency of 0.36±0.03 (a loss of 4.5 ±0.4 dB) at a signal frequency of 185 GHz, including losses in the coupling horn and the waveguide. The performance was measured with the hot-cold source technique. The effects of nonheterodyne response in that situation were investigated in detail. The junctions have been operated in a coherent receiver that can be used on a telescope with only small adaptations. The instantaneous bandwidth of the receiver is about 20 GHz.