Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Magnetics

Noise in Josephson effect mm-wave mixers

J. H. Claassen, Y. Taur, P. L. Richards

Published Mar 1, 1975• 1 citation
Publisher

Abstract

We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.

DOI
10.1109/tmag.1975.1058615

Related papers

Noise in Josephson point contacts with and without rf bias

J. H. Claassen, Y. Taur, P. L. Richards

Point contact Josephson junctions operated as microwave mixers at 36 GHz show conversion gain and lower noise than cooled Schottky barrier diodes in the same application. The noise in such junctions with and without rf bias is explored both experimentally and theoretically. The noise power is found to be about a factor 2 above the thermal noise in the resistively shunted junction model. In contrast to previous reports, the inclusion of a shot noise term in the theory for no rf bias overestimates the observed noise substantially.

Applied Physics Letters•Dec 15, 1974•31 citations

Point-contact Josephson mixers at 130 GHz

J. H. Claassen, P. L. Richards

The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.

Journal of Applied Physics•Jul 1, 1978•28 citations

Josephson Junctions as Heterodyne Detectors

Y. Taur, J. H. Claassen, P. L. Richards

Heterodyne detection with a point-contact Josephson junction has been investigated both experimentally and theoretically. The measured performance of the device at 36 GHz is in good agreement with the theory. By operating vanadium point contacts at 1.4 K, we have achieved a single-sideband (SSB) mixer noise temperature of 54K with a conversion gain of 1.35 and a signal bandwidth on the order of 1 GHz. From our results we can extrapolate a potentially impressive performance for these devices at submillimeter wavelengths.

IEEE Transactions on Microwave Theory and Techniques•Dec 1, 1974•27 citations

Conversion gain and noise in a Josephson mixer

Y. Taur, J. H. Claassen, P. L. Richards

Fundamental mixing at 36 GHz in non-hysteretic Nb point contacts has been observed with overall conversion efficiencies in the range 0.33 ≤ η ≤ 4 and mixer noise temperatures in the neighborhood of TM ~ 200 K. The observed conversion efficiencies are in good agreement with the Resistively Shunted Junction model. The observed noise can be accounted for by assuming that the Johnson noise in the shunt resistor is the only source of noise driving the junction. Somewhat larger noise is seen from resonantly coupled mixers than is seen when the mixer is driven from an rf current source. Fundamental mixing in hysteretic junctions is limited to a narrow if bandwidth and gives much larger conversion gain but also larger noise. Parametric amplification at the if frequency is seen in hysteretic junctions. Fourth order harmonic mixing with ωLO/2 π at 9 GHz has been achieved with performance almost comparable to fundamental mixing. Cavity mode mixing appears less promising.

Revue de Physique Appliquée•Jan 1, 1974•39 citations

Studies of noise in Josephson-effect mixers and their potential for submillimeter heterodyne detection

Robert J. Schoelkopf

NOTE: Text or symbols not renderable in plain ASCII are indicated by [...]. Abstract is included in .pdf document. This thesis describes both theoretical and experimental investigations into the dynamics and noise processes of Josephson junctions, with the intent of evaluating their potential as mixers in heterodyne instruments for submillimeter-wave (i.e., the frequency range from 300 GHz to 3THz) detection. Superconducting tunnel junctions utilizing the nonlinearity due to photon-assisted tunneling of quasiparticles (SIS mixers) have become the state-of-the-art technology for sensitive heterodyne detection up to frequencies of about 700 [...]. Recent progress in the fabrication of high [...], superconductors has led to Josephson-effect devices with [...] products of up to ten millivolts, which might be suitable for mixing at frequencies of many terahertz. The key question for weighing the prospects for high-frequency Josephson mixers is that of the sensitivity which can be attained. Previous experimental work on Josephson mixing suggests the existence of an "excess" noise, which degrades the sensitivity. Theoretical modeling of mixer performance, based on the resistivelyshunted junction (RSJ) model for the dynamics of the device, also indicates the presence of larger noise than expected. The origin of this noise was not clearly understood, however, nor was its exact magnitude or expected scaling with frequency or junction characteristics known. In addition, previous experiments utilized crude devices of the point-contact type, which were unstable and thus undesirable for real applications. In the first part of this thesis research, extensive numerical simulations were performed with the RSJ model, including calculations of mixer noise and conversion efficiency. These calculations have revealed that the source of excess noise is the AC Josephson oscillations of the device, which can be completely incoherent, with a linewidth comparable to their frequency. Thus they appear as a broadband noise source. While this noise is intrinsic and unavoidable, an optimized mixer is still shown to be capable of interesting sensitivity levels, and the excess noise is expected to become relatively less important as the operating frequency is increased. Secondly, a process has been developed for the fabrication of stable, well-characterized, and reproducible Josephson devices based on resistively-shunted Nb and NbN tunnel junctions. The devices utilize submicron-area, high current-density tunnel junctions and a AuGe shunt resistor to yield completely non-hysteretic I-V curves, normal-state resistances of about [...] products of about half a millivolt. These devices should be nearly optimal for mixing at [...]. Heterodyne measurements using these junctions have been performed in a waveguide mixer mount. Receiver temperatures as low as 190 K (DSB), with -6 dB conversion efficiency, have been obtained at 100 [...], but these results are still a factor of about four higher than those predicted by the RSJ simulations. Accurate measurements of the available noise power of the junctions at the intermediate frequency of 1.5 [...] were made, and confirmed that the receivers were limited by elevated junction output noise. The deviations of the noise from theoretical predictions are shown to be caused by the nonlinear interaction of the junction with the embedding circuit. While this work points out some of the complexity introduced by the strong nonlinearity of Josephson devices, it is still expected that Josephson-effect mixers may be useful for heterodyne detection at very high frequencies.

•Nov 7, 2007•5 citations

Conversion gain in a Josephson effect mixer

Y. Taur, J. H. Claassen, P. L. Richards

The measured performance of Nb–Nb point contact Josephson junctions used as 36-GHz microwave mixers is in good agreement with the predictions of the resistively shunted junction model. Conversion efficiencies greater than unity are attained, with mixer noise temperatures comparable with the best competing devices.

Applied Physics Letters•Jan 15, 1974•55 citations
We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.
Point contact Josephson junctions operated as microwave mixers at 36 GHz show conversion gain and lower noise than cooled Schottky barrier diodes in the same application. The noise in such junctions with and without rf bias is explored both experimentally and theoretically. The noise power is found to be about a factor 2 above the thermal noise in the resistively shunted junction model. In contrast to previous reports, the inclusion of a shot noise term in the theory for no rf bias overestimates the observed noise substantially.
The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.
Heterodyne detection with a point-contact Josephson junction has been investigated both experimentally and theoretically. The measured performance of the device at 36 GHz is in good agreement with the theory. By operating vanadium point contacts at 1.4 K, we have achieved a single-sideband (SSB) mixer noise temperature of 54K with a conversion gain of 1.35 and a signal bandwidth on the order of 1 GHz. From our results we can extrapolate a potentially impressive performance for these devices at submillimeter wavelengths.
Fundamental mixing at 36 GHz in non-hysteretic Nb point contacts has been observed with overall conversion efficiencies in the range 0.33 ≤ η ≤ 4 and mixer noise temperatures in the neighborhood of TM ~ 200 K. The observed conversion efficiencies are in good agreement with the Resistively Shunted Junction model. The observed noise can be accounted for by assuming that the Johnson noise in the shunt resistor is the only source of noise driving the junction. Somewhat larger noise is seen from resonantly coupled mixers than is seen when the mixer is driven from an rf current source. Fundamental mixing in hysteretic junctions is limited to a narrow if bandwidth and gives much larger conversion gain but also larger noise. Parametric amplification at the if frequency is seen in hysteretic junctions. Fourth order harmonic mixing with ωLO/2 π at 9 GHz has been achieved with performance almost comparable to fundamental mixing. Cavity mode mixing appears less promising.
NOTE: Text or symbols not renderable in plain ASCII are indicated by [...]. Abstract is included in .pdf document. This thesis describes both theoretical and experimental investigations into the dynamics and noise processes of Josephson junctions, with the intent of evaluating their potential as mixers in heterodyne instruments for submillimeter-wave (i.e., the frequency range from 300 GHz to 3THz) detection. Superconducting tunnel junctions utilizing the nonlinearity due to photon-assisted tunneling of quasiparticles (SIS mixers) have become the state-of-the-art technology for sensitive heterodyne detection up to frequencies of about 700 [...]. Recent progress in the fabrication of high [...], superconductors has led to Josephson-effect devices with [...] products of up to ten millivolts, which might be suitable for mixing at frequencies of many terahertz. The key question for weighing the prospects for high-frequency Josephson mixers is that of the sensitivity which can be attained. Previous experimental work on Josephson mixing suggests the existence of an "excess" noise, which degrades the sensitivity. Theoretical modeling of mixer performance, based on the resistivelyshunted junction (RSJ) model for the dynamics of the device, also indicates the presence of larger noise than expected. The origin of this noise was not clearly understood, however, nor was its exact magnitude or expected scaling with frequency or junction characteristics known. In addition, previous experiments utilized crude devices of the point-contact type, which were unstable and thus undesirable for real applications. In the first part of this thesis research, extensive numerical simulations were performed with the RSJ model, including calculations of mixer noise and conversion efficiency. These calculations have revealed that the source of excess noise is the AC Josephson oscillations of the device, which can be completely incoherent, with a linewidth comparable to their frequency. Thus they appear as a broadband noise source. While this noise is intrinsic and unavoidable, an optimized mixer is still shown to be capable of interesting sensitivity levels, and the excess noise is expected to become relatively less important as the operating frequency is increased. Secondly, a process has been developed for the fabrication of stable, well-characterized, and reproducible Josephson devices based on resistively-shunted Nb and NbN tunnel junctions. The devices utilize submicron-area, high current-density tunnel junctions and a AuGe shunt resistor to yield completely non-hysteretic I-V curves, normal-state resistances of about [...] products of about half a millivolt. These devices should be nearly optimal for mixing at [...]. Heterodyne measurements using these junctions have been performed in a waveguide mixer mount. Receiver temperatures as low as 190 K (DSB), with -6 dB conversion efficiency, have been obtained at 100 [...], but these results are still a factor of about four higher than those predicted by the RSJ simulations. Accurate measurements of the available noise power of the junctions at the intermediate frequency of 1.5 [...] were made, and confirmed that the receivers were limited by elevated junction output noise. The deviations of the noise from theoretical predictions are shown to be caused by the nonlinear interaction of the junction with the embedding circuit. While this work points out some of the complexity introduced by the strong nonlinearity of Josephson devices, it is still expected that Josephson-effect mixers may be useful for heterodyne detection at very high frequencies.