Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Point-contact Josephson mixers at 130 GHz

J. H. Claassen, P. L. Richards

Published Jul 1, 1978• 28 citations
Publisher

Abstract

The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.

DOI
10.1063/1.325375

Related papers

Noise in Josephson effect mm-wave mixers

J. H. Claassen, Y. Taur, P. L. Richards

We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.

IEEE Transactions on Magnetics•Mar 1, 1975•1 citation

Conversion gain in a Josephson effect mixer

Y. Taur, J. H. Claassen, P. L. Richards

The measured performance of Nb–Nb point contact Josephson junctions used as 36-GHz microwave mixers is in good agreement with the predictions of the resistively shunted junction model. Conversion efficiencies greater than unity are attained, with mixer noise temperatures comparable with the best competing devices.

Applied Physics Letters•Jan 15, 1974•55 citations

Performance limits of a Josephson-junction mixer

J. H. Claassen, P. L. Richards

We present the results of extensive analog-computer simulations of a Josephson junction used as a mixer with an external local oscillator. The resistively shunted junction model was used throughout, and the effects of intrinsic junction noise were included. When the source impedance is much greater than the junction resistance R, our simulations permit predictions of conversion efficiency, noise temperature, and saturation level to be made for a wide range of experimental parameters. The possibility of harmonic mixing has also been considered. With a source resistance comparable to R (i.e., conventional ’’matching’’) the behavior of the system is too complicated to permit such general predictions of performance. From the results of simulations for a particular set of parameters, it appears that the best noise temperature will usually be achieved for a source impedance somewhat greater than R. An upper limit for the mixer-noise temperature is ∼40T over a broad range of junction parameters, where T is the effective temperature of the junction. The conversion efficiency under these circumstances should be comparable to what is potentially available from Schottky-diode mixers. Our simulations show that with stronger microwave coupling it is possible to obtain conversion gain—i.e., a conversion efficiency exceeding unity. This, however, will probably be at the expense of a higher mixer-noise temperature. Saturation can be important even for source temperatures ∼300 K. To avoid saturation it is necessary either to restrict the coupling bandwith or use an array of junctions.

Journal of Applied Physics•Jul 1, 1978•42 citations

Conversion gain in a Josephson effect mixer. Technical rept

Yuan Taur, J. H. Claassen, P. L. Richards

The measured performance of Nb-Nb point contact Josephson-junctions used as 36 GHz microwave mixers is in good agreement with the predictions of the resistively shunted junction model. Conversion efficiencies greater than one are attained, with mixer noise temperatures comparable with the best competing devices.

•Oct 1, 1973•0 citations

Josephson heterodyne detection at high thermal background levels

Tim Poorter

Point-contact Josephson junctions with a submicron contact diameter have been used as high-frequency mixers (170–220 GHz) under high thermal background conditions. The junction is formed across a full height (0.56×1.06 mm2) waveguide between a 3–5-μm thick Nb whisker and a 0.2-mm diam Nb center conductor of a coaxial line. The best single-side band mixer-noise temperature that was measured is 165 K (± 25%) with a corresponding single-side band conversion efficiency of 0.36±0.03 (a loss of 4.5 ±0.4 dB) at a signal frequency of 185 GHz, including losses in the coupling horn and the waveguide. The performance was measured with the hot-cold source technique. The effects of nonheterodyne response in that situation were investigated in detail. The junctions have been operated in a coherent receiver that can be used on a telescope with only small adaptations. The instantaneous bandwidth of the receiver is about 20 GHz.

Journal of Applied Physics•Jan 1, 1982•27 citations

Josephson frequency conversion in the range 145–1600 GHz with Nb–Nb superconducting point contacts used as oscillator-mixer

G. Vernet, Robert Adde

The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb–Nb point-contact junctions at 4.2 °K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1, 0.3, and 9.2 GHz. The point contact is in a nonresonant structure and fed by a constant current source: neither a strong rf coupling of the contact with a cavity nor a stabilizing shunt resistance was proved necessary. The direct observation of frequency conversion was performed with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1600 GHz. The experiments with intermediate frequencies fi of 0.1 and 0.3 GHz indicate that conventional frequency conversion does not occur but that the observed signals are related to noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. The results show that low-frequency current components are induced in the junction, which can give large spurious signals when small i.f. are used.

Journal of Applied Physics•Jun 1, 1974•13 citations
The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.
We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.
We present the results of extensive analog-computer simulations of a Josephson junction used as a mixer with an external local oscillator. The resistively shunted junction model was used throughout, and the effects of intrinsic junction noise were included. When the source impedance is much greater than the junction resistance R, our simulations permit predictions of conversion efficiency, noise temperature, and saturation level to be made for a wide range of experimental parameters. The possibility of harmonic mixing has also been considered. With a source resistance comparable to R (i.e., conventional ’’matching’’) the behavior of the system is too complicated to permit such general predictions of performance. From the results of simulations for a particular set of parameters, it appears that the best noise temperature will usually be achieved for a source impedance somewhat greater than R. An upper limit for the mixer-noise temperature is ∼40T over a broad range of junction parameters, where T is the effective temperature of the junction. The conversion efficiency under these circumstances should be comparable to what is potentially available from Schottky-diode mixers. Our simulations show that with stronger microwave coupling it is possible to obtain conversion gain—i.e., a conversion efficiency exceeding unity. This, however, will probably be at the expense of a higher mixer-noise temperature. Saturation can be important even for source temperatures ∼300 K. To avoid saturation it is necessary either to restrict the coupling bandwith or use an array of junctions.
Point-contact Josephson junctions with a submicron contact diameter have been used as high-frequency mixers (170–220 GHz) under high thermal background conditions. The junction is formed across a full height (0.56×1.06 mm2) waveguide between a 3–5-μm thick Nb whisker and a 0.2-mm diam Nb center conductor of a coaxial line. The best single-side band mixer-noise temperature that was measured is 165 K (± 25%) with a corresponding single-side band conversion efficiency of 0.36±0.03 (a loss of 4.5 ±0.4 dB) at a signal frequency of 185 GHz, including losses in the coupling horn and the waveguide. The performance was measured with the hot-cold source technique. The effects of nonheterodyne response in that situation were investigated in detail. The junctions have been operated in a coherent receiver that can be used on a telescope with only small adaptations. The instantaneous bandwidth of the receiver is about 20 GHz.
The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb–Nb point-contact junctions at 4.2 °K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1, 0.3, and 9.2 GHz. The point contact is in a nonresonant structure and fed by a constant current source: neither a strong rf coupling of the contact with a cavity nor a stabilizing shunt resistance was proved necessary. The direct observation of frequency conversion was performed with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1600 GHz. The experiments with intermediate frequencies fi of 0.1 and 0.3 GHz indicate that conventional frequency conversion does not occur but that the observed signals are related to noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. The results show that low-frequency current components are induced in the junction, which can give large spurious signals when small i.f. are used.