Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Soviet physics. Technical physics

Josephson-junction mm-wave mixer

В. А. Ильин, M. S. Kamenetskaia, T. M. Shurminova, V. S. Étkin

Published Sep 1, 1982• 0 citations
OpenAlex

Abstract

The design of a mixer based on a Josephson point junction operating at lambda = 2 mm is described. A distinctive feature of the mixer is that it uses an intermediate microwave frequency (f/sub int/ = 10 GHz). The conversion losses referred to the contact are < or =12 dB and the noise temperature approx.180 K.

Related papers

Josephson junction mm-wave mixer without matching structure

Qi Cheng, Sen Yang, Yan Sheng

This paper describes a Josephson junction mixer at 8-mm wavelength without matching structure. With a Nb point contact operating at 4.2 K, a single-sideband mixer noise temperature T/sub M/approx.100 K and a conversion efficiency etaapprox.0.8 were measured by the Y-factor method of hot/cold noise. The mechanism of the mixing noise is also discussed.

Chin. Phys.; (United States)•Apr 1, 1982•0 citations

Results, Potentials, and Limitations of Josephson-Mixer Receivers at Millimeter and Long Submillimeter Wavelengths

JOCHEN EDRICH, B. Sullivan, Donald G. McDonald

Millimeter-wave mixers using Josephson point contacts are described, which exhibit a conversion loss L/sub c/ = 9.5 dB and a noise temperature T ~ 223 K for lambda >or= 0.95 mm. Their potentials and limitations in noise, bandwidth, drive power, and stability for receiver applications are discussed.

IEEE Transactions on Microwave Theory and Techniques•Jun 1, 1977•21 citations

Noise in Josephson effect mm-wave mixers

J. H. Claassen, Y. Taur, P. L. Richards

We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.

IEEE Transactions on Magnetics•Mar 1, 1975•1 citation

Frequency conversion with superconducting point contacts operating as oscillator-mixers and its application to the measurement of the linewidth of the Josephson current at very high frequency

G. Vernet, Robert Adde

The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb-Nb point contact junctions at 4.2 K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1 and 9.2 GHz. Frequency conversion signals are only detected in the latter case with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1 600 GHz. The experiments with intermediate frequency fi of 0.1 GHz indicate for this small value of f i that the observed signals are not related to frequency conversion but noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. We have then investigated the noise properties up to 450 GHz of superconducting point-contacts using the junction as an oscillator-mixer where the Josephson current is mixed with harmonics of an externally applied signal. The emitted intermediate frequency is detected at 9.2 GHz and its linewidth is measured. In the very high frequency range the dc quasiparticle current dominates in a Josephson weak-link and we compare the corresponding theoretical linewidth calculated by Scalapino with our experimental results.

Revue de Physique Appliquée•Jan 1, 1974•3 citations

Josephson frequency conversion in the range 145–1600 GHz with Nb–Nb superconducting point contacts used as oscillator-mixer

G. Vernet, Robert Adde

The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb–Nb point-contact junctions at 4.2 °K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1, 0.3, and 9.2 GHz. The point contact is in a nonresonant structure and fed by a constant current source: neither a strong rf coupling of the contact with a cavity nor a stabilizing shunt resistance was proved necessary. The direct observation of frequency conversion was performed with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1600 GHz. The experiments with intermediate frequencies fi of 0.1 and 0.3 GHz indicate that conventional frequency conversion does not occur but that the observed signals are related to noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. The results show that low-frequency current components are induced in the junction, which can give large spurious signals when small i.f. are used.

Journal of Applied Physics•Jun 1, 1974•13 citations

Superconducting Microwave Mixers Utilizing Josephson Junctions

A. DiNardo, E. Sard

Microwave superconducting mixers operating at 10–13 GHz utilizing Josephson junctions have been investigated analytically and experimentally. Measurements on mixer sensitivity were carried out at 13 GHz using waveguide-mounted experimental point-contact Josephson junctions at 4.2 K. Results showed sensitivities of −90 dBm/MHz (10−18 W/Hz) which included mismatch losses encountered in the waveguide structure. The Josephson junction mixing mechanism was analyzed on the basis of small-signal modulation of the staircase like dc I-V characteristics. It was shown that a small-signal microwave excitation results in an ac lateral shift of the regions between steps, such that: (a) Optimum Josephson mixing occurs halfway between steps. (b) Mixing occurs between all steps with maximum conversion efficiency between the zero and first step. (c) Predicted low conversion loss and possibly internal gain for a matched mixer. The analytical model was simulated by a digital computer and the behavior of the Josephson mixer predicted for various conditions of excitation. The model chosen for the analysis and the computer simulation is based on the simplest assumptions concerning bulk-formed Josephson junctions. In the laboratory an external local oscillator set 60 MHz below the signal frequency was used to induce the well-known step structure in the dc I-V characteristic of the point-contact Josephson junction. Mixing of the Lo and signal was found to occur between constant voltage steps in agreement with both analysis and computer simulation. The correctness of the model is demonstrated by the agreement between the theory and experiment.

Journal of Applied Physics•Jan 1, 1971•7 citations
We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.
The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb-Nb point contact junctions at 4.2 K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1 and 9.2 GHz. Frequency conversion signals are only detected in the latter case with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1 600 GHz. The experiments with intermediate frequency fi of 0.1 GHz indicate for this small value of f i that the observed signals are not related to frequency conversion but noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. We have then investigated the noise properties up to 450 GHz of superconducting point-contacts using the junction as an oscillator-mixer where the Josephson current is mixed with harmonics of an externally applied signal. The emitted intermediate frequency is detected at 9.2 GHz and its linewidth is measured. In the very high frequency range the dc quasiparticle current dominates in a Josephson weak-link and we compare the corresponding theoretical linewidth calculated by Scalapino with our experimental results.
The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb–Nb point-contact junctions at 4.2 °K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1, 0.3, and 9.2 GHz. The point contact is in a nonresonant structure and fed by a constant current source: neither a strong rf coupling of the contact with a cavity nor a stabilizing shunt resistance was proved necessary. The direct observation of frequency conversion was performed with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1600 GHz. The experiments with intermediate frequencies fi of 0.1 and 0.3 GHz indicate that conventional frequency conversion does not occur but that the observed signals are related to noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. The results show that low-frequency current components are induced in the junction, which can give large spurious signals when small i.f. are used.
Microwave superconducting mixers operating at 10–13 GHz utilizing Josephson junctions have been investigated analytically and experimentally. Measurements on mixer sensitivity were carried out at 13 GHz using waveguide-mounted experimental point-contact Josephson junctions at 4.2 K. Results showed sensitivities of −90 dBm/MHz (10−18 W/Hz) which included mismatch losses encountered in the waveguide structure. The Josephson junction mixing mechanism was analyzed on the basis of small-signal modulation of the staircase like dc I-V characteristics. It was shown that a small-signal microwave excitation results in an ac lateral shift of the regions between steps, such that: (a) Optimum Josephson mixing occurs halfway between steps. (b) Mixing occurs between all steps with maximum conversion efficiency between the zero and first step. (c) Predicted low conversion loss and possibly internal gain for a matched mixer. The analytical model was simulated by a digital computer and the behavior of the Josephson mixer predicted for various conditions of excitation. The model chosen for the analysis and the computer simulation is based on the simplest assumptions concerning bulk-formed Josephson junctions. In the laboratory an external local oscillator set 60 MHz below the signal frequency was used to induce the well-known step structure in the dc I-V characteristic of the point-contact Josephson junction. Mixing of the Lo and signal was found to occur between constant voltage steps in agreement with both analysis and computer simulation. The correctness of the model is demonstrated by the agreement between the theory and experiment.