Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2509.00172 · Physical Review Applied

Microfabricated alkali-vapor cells with tunable He - Ne buffer-gas mixture using reservoirs with laser-actuated break seals

Clément Carlé, Andrei Mursa, G. Faure, Shervin Keshavarzi, Quentin A. A. Tanguy, Emmanuel Klinger, Vincent N. Maurice, Rodolphe Boudot, Nicolas Passilly

Published Dec 24, 2025• 1 citation
arXivHTMLPDF

Abstract

This letter reports on the generation of a tunable buffer gas mixture within microfabricated alkali vapor cells. We show that the combination of low-permeation windows with sequential openings of laser-actuated break-seals enables adjustment of a helium-neon (He-Ne) noble gas mixture, fully compatible with alkali metal dispensers. The gas reservoirs and the main cell cavities are initially sealed at the wafer level under distinct helium and neon atmospheres, respectively. Within each cell, after Cs vapor is released from the dispenser, the break-seals are successively actuated to incrementally increase the helium fraction in the buffer gas mixture. This process shifts the atomic clock frequency turnover temperature toward higher values. As an illustration, one of the fabricated cells was operated at 95$^{\circ}$C in a coherent population trapping clock, achieving a fractional frequency stability of 9$\times$10$^{-11}$ at one-day integration time. These results demonstrate the feasibility of precisely tuning buffer gas compositions in microfabricated vapor cells and support the suitability of He-Ne mixtures for miniature atomic clock applications.

DOI
10.1103/wyz6-rntk

Related papers

Cs vapor microcells with Ne-He buffer gas mixture for high operation-temperature miniature atomic clocks

Eric Kroemer, Moustafa Abdel Hafiz, Vincent N. Maurice +3 more

We report on the characterization of Cs vapor microfabricated cells filled with a Ne-He buffer gas mixture using coherent population trapping (CPT) spectroscopy. The temperature dependence of the Cs clock frequency is found to be canceled at the first order around a so-called inversion temperature higher than 80°C whose value depends on the buffer gas partial pressure ratio. This buffer gas mixture could be well-adapted for the development of miniature atomic clocks devoted to be used in specific applications such as defense and avionic systems with high operating temperature environment (typically higher than 85°C). This solution suggests an alternative to buffer gas mixtures generally used in optically-pumped vapor cell atomic clocks.

Optics Express•Jul 7, 2015•22 citations

Versatile microfabricated alkali vapor cells using local sealing

Vincent N. Maurice, Ravinder Chutani, Clément Carlé +7 more

We report on a new technique to form and seal microfabricated cells that alleviates some of the limitations imposed by current solutions. The technique consists in integrating single-use sealing structures that can be actuated through laser irradiation, either to isolate cavities from each other or to connect them. Inspired by the well-established glass-blowing techniques, it reproduces on a wafer the “make-seal” and “break-seal” features found in conventional cell filling setups. By allowing cells to be evacuated, filled and sealed after having been fully-formed, this technique opens new venues for atomic devices. Here, we demonstrate both features and present one use case where alkali dispensers are used in association with non-noble gasses despite their gettering ability.

•Apr 24, 2022•0 citations

Microfabricated Alkali Atom Vapor Cells for Chip Scale Atomic Clock

M.-Z. Huang, Jiashan Zhu, Guangfeng Shi +2 more

In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.

Annual Conference of the Chinese Society of Micro-Nano Technology (CSMNT)•Nov 22, 2017•0 citations

Microfabricated vapor cells filled with a cesium dispensing paste for miniature atomic clocks

Vincent N. Maurice, J. Rutkowski, Eric Kroemer +6 more

A method for filling alkali vapor cells with cesium from a dispensing paste is proposed and its compliance with miniature atomic clock applications is evaluated. The paste is an organic-inorganic composition of cesium molybdate, zirconium-aluminum powder, and a hybrid organic-inorganic binder. It is compatible with collective deposition processes such as micro-drop dispensing, which can be done under ambient atmosphere at the wafer-level. After deposition and sealing by anodic bonding, cesium is released from the consolidated paste through local heating with a high power laser. Linear absorption signals have been observed over one year in several cells, showing a stable atomic density. For further validation of this technology for clock applications, one cell has been implemented in a coherent population trapping clock setup to monitor its frequency stability. A fractional frequency aging rate around –4.4 × 10−12 per day has been observed, which is compliant with a clock frequency instability below 1 × 10−11 at one day integration time. This filling method can drastically reduce the cost and the complexity of alkali vapor cell fabrication.

Applied Physics Letters•Apr 17, 2017•42 citations

Atomic vapor cells for chip-scale atomic clocks with improved long-term frequency stability

Svenja A. Knappe, Vladislav P. Gerginov, Peter D. D. Schwindt +4 more

A novel technique for microfabricating alkali atom vapor cells is described in which alkali atoms are evaporated into a micromachined cell cavity through a glass nozzle. A cell of interior volume 1 mm3, containing 87Rb and a buffer gas, was made in this way and integrated into an atomic clock based on coherent population trapping. A fractional frequency instability of 6 x 10(-12) at 1000 s of integration was measured. The long-term drift of the F=1, mF=0-->F=2, mF=0 hyperfine frequency of atoms in these cells is below 5 x 10(-11)/day.

Optics Letters•Sep 15, 2005•223 citations

Wafer-scale fabrication of temperature-compensated alkali vapor cells

Yang Li, Marlou R. Slot, Matthew T. Hummon +2 more

We demonstrate wafer-scale fabrication of temperature-compensated alkali vapor cells using a mixture of Ar and N2 buffer gases. The temperature coefficient of the fractional frequency shift of the hyperfine clock resonance is reduced from a typical value of ≈30×10−9/ K for cells containing pure N2 to below ≈3×10−9/ K for the buffer gas mixture. This result is an important step toward the mass production of temperature-compensated atomic vapor cell-based devices such as chip-scale atomic clocks.

Applied Physics Letters•Jun 2, 2025•10 citations
This letter reports on the generation of a tunable buffer gas mixture within microfabricated alkali vapor cells. We show that the combination of low-permeation windows with sequential openings of laser-actuated break-seals enables adjustment of a helium-neon (He-Ne) noble gas mixture, fully compatible with alkali metal dispensers. The gas reservoirs and the main cell cavities are initially sealed at the wafer level under distinct helium and neon atmospheres, respectively. Within each cell, after Cs vapor is released from the dispenser, the break-seals are successively actuated to incrementally increase the helium fraction in the buffer gas mixture. This process shifts the atomic clock frequency turnover temperature toward higher values. As an illustration, one of the fabricated cells was operated at 95∘^{\circ}∘C in a coherent population trapping clock, achieving a fractional frequency stability of 9×\times×10−11^{-11}−11 at one-day integration time. These results demonstrate the feasibility of precisely tuning buffer gas compositions in microfabricated vapor cells and support the suitability of He-Ne mixtures for miniature atomic clock applications.
We report on the characterization of Cs vapor microfabricated cells filled with a Ne-He buffer gas mixture using coherent population trapping (CPT) spectroscopy. The temperature dependence of the Cs clock frequency is found to be canceled at the first order around a so-called inversion temperature higher than 80°C whose value depends on the buffer gas partial pressure ratio. This buffer gas mixture could be well-adapted for the development of miniature atomic clocks devoted to be used in specific applications such as defense and avionic systems with high operating temperature environment (typically higher than 85°C). This solution suggests an alternative to buffer gas mixtures generally used in optically-pumped vapor cell atomic clocks.
We report on a new technique to form and seal microfabricated cells that alleviates some of the limitations imposed by current solutions. The technique consists in integrating single-use sealing structures that can be actuated through laser irradiation, either to isolate cavities from each other or to connect them. Inspired by the well-established glass-blowing techniques, it reproduces on a wafer the “make-seal” and “break-seal” features found in conventional cell filling setups. By allowing cells to be evacuated, filled and sealed after having been fully-formed, this technique opens new venues for atomic devices. Here, we demonstrate both features and present one use case where alkali dispensers are used in association with non-noble gasses despite their gettering ability.
In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.
A method for filling alkali vapor cells with cesium from a dispensing paste is proposed and its compliance with miniature atomic clock applications is evaluated. The paste is an organic-inorganic composition of cesium molybdate, zirconium-aluminum powder, and a hybrid organic-inorganic binder. It is compatible with collective deposition processes such as micro-drop dispensing, which can be done under ambient atmosphere at the wafer-level. After deposition and sealing by anodic bonding, cesium is released from the consolidated paste through local heating with a high power laser. Linear absorption signals have been observed over one year in several cells, showing a stable atomic density. For further validation of this technology for clock applications, one cell has been implemented in a coherent population trapping clock setup to monitor its frequency stability. A fractional frequency aging rate around –4.4 × 10−12 per day has been observed, which is compliant with a clock frequency instability below 1 × 10−11 at one day integration time. This filling method can drastically reduce the cost and the complexity of alkali vapor cell fabrication.
A novel technique for microfabricating alkali atom vapor cells is described in which alkali atoms are evaporated into a micromachined cell cavity through a glass nozzle. A cell of interior volume 1 mm3, containing 87Rb and a buffer gas, was made in this way and integrated into an atomic clock based on coherent population trapping. A fractional frequency instability of 6 x 10(-12) at 1000 s of integration was measured. The long-term drift of the F=1, mF=0-->F=2, mF=0 hyperfine frequency of atoms in these cells is below 5 x 10(-11)/day.
We demonstrate wafer-scale fabrication of temperature-compensated alkali vapor cells using a mixture of Ar and N2 buffer gases. The temperature coefficient of the fractional frequency shift of the hyperfine clock resonance is reduced from a typical value of ≈30×10−9/ K for cells containing pure N2 to below ≈3×10−9/ K for the buffer gas mixture. This result is an important step toward the mass production of temperature-compensated atomic vapor cell-based devices such as chip-scale atomic clocks.