Techniques in frequency stabilization of lasers to fixed-spacer optical cavities have advanced to the point where the ultimate frequency stabilities are limited by thermal noise for standard cavity configurations at room temperature. In early experiments, laser stabilization via spectral-hole burning (SHB) has been shown to be a promising alternative. In this Letter, we explore the thermal-noise limits to frequency stability in spectral holes and compile known material parameters for a typical system used in SHB experiments (Eu3+ doped Y2SiO5) to make numerical estimates for the fundamental thermal-noise induced frequency instability in spectral holes for the liquid-helium temperature and dilution temperature cases. These efforts can guide the design of future SHB experiments and clarify which important material parameters remain to be measured.
Techniques in frequency stabilization of lasers to fixed-spacer optical cavities have advanced to the point where the ultimate frequency stabilities are limited by thermal noise for standard cavity configurations at room temperature. In early experiments, laser stabilization via spectral-hole burning (SHB) has been shown to be a promising alternative. In this Letter, we explore the thermal-noise limits to frequency stability in spectral holes and compile known material parameters for a typical system used in SHB experiments (Eu3+ doped Y2SiO5) to make numerical estimates for the fundamental thermal-noise induced frequency instability in spectral holes for the liquid-helium temperature and dilution temperature cases. These efforts can guide the design of future SHB experiments and clarify which important material parameters remain to be measured.
This poster presents the status of the development of an ultra-frequency stable laser via a spectroscopic technique known as Spectral Hole Burning (SHB). In short, we can use a pump laser to imprint, or ’burn’, transmissive spectral lines, or ’spectral holes’, in the otherwise inhomogeneously broadened absorptive spectral sites of a Eu3+ doped Y2SiO5 crystal. We can then lock a probe laser to these narrow spectral features achieving our frequency stabilized laser. Of great concern is the frequency stability of the spectral holes, such as their sensitivity to temperature changes which we characterize here. Additionally, a challenge this experiment faces is the restriction of probe laser power to avoid damaging the spectral features. This sets a relatively high level of shot noise, limiting the detection sensitivity. Here we present our solution to overcome this difficulty by using a multi-spectral- hole probing scheme to average the probing signals of several burned spectral holes.
As basic building blocks for quantum devices, ultra-stable lasers have a profound impact on various fields. Longer laser coherence times enhance the performance of quantum sensors, computers, communications, and optical clocks. Although optical lattice clocks have accomplished significant high-precision measurements, they often fall short of their quantum projection noise limits due to dead times during atom preparation: the instability in the laser frequency introduces stochastic fluctuations during the interrogation of atomic transitions (Dick effect). High-resolution optical clock comparisons are crucial for evaluating their accuracy and could lead to a redefinition of the SI second based on optical transitions [1].However, the most common technique for achieving ultra-stable lasers, the Pound-Drever-Hall method with Fabry-Perot cavities, faces thermal noise limitations of the cavities. To overcome these constraints, alternative methods such as Spectral Hole Burning (SHB) in rare-earth-doped crystals (REICs) have been explored. Indeed, REICs experience inhomogeneous broadening due to local lattice distortions caused by the size difference between dopant and host ions. An SHB protocol, which creates narrow spectral features through selective depletion of specific dopant ion populations using narrow-linewidth lasers, allows to overcome the inhomogeneous broadening and fully exploit the coherence of rare-earth ions. At cryogenic temperatures, Eu:YSO crystal exhibit persistent Spectral Holes a few kHz narrow and with a lifetime up to 10 h, at 4 K [2], making it a high-precision frequency reference, ideal for intermediate-timescale sensing.We report recent experimental progress on SHB in Eu:YSO crystals at specific sub-K dilution temperature setpoints that cancel the thermal sensitivity of the hole frequency [3]. The latest recorded performances on our experiment reach a fractional frequency stability of 4.10-16 at 1 s [4], which is close to the perfomance of our reference cavity at LTE. Therefore, a second SHB setup is needed for our future stability comparisons. On one front, we rationalize our SHB protocol and investigate new optimal burning parameters as well as test various doping concentrations to achieve the narrowest possible spectral holes on both setups. On another, we continue to further improving the laser frequency lock onto spectral holes, by cancelling as many systematic noise sources as possible. We provide the performances of our Michelson interferometer to reject frequency noise induced on light propagation to the crystal and by the cryostat acoustic vibrations. In addition, we explore a group delay measurement technique via phase modulation to enhance the precision on the pointing of the center of spectral holes. This should help removing slow frequency drifts due to asymmetric burning of the hole while it is probed by the laser.
Spectral hole burning in rare earth doped crystal can provide frequency references based on the optical transition of the dopant ions [1] . The narrow spectral patterns can be used to improve laser frequency stabilization [2] , [3] and provide a new generation of ultra-stable lasers with lower thermal noise benefiting from the cryogenic environment and better quality factor of the crystal than the amorphous glass typically used in the Fabry-Perot cavity. We utilize Europium doped yttrium silicon oxide (Eu:YSO) in our experiments, which allow realization of long lived (hours or more depending on temperature) narrow spectral holes ( kHz or less) well suited for high precision experiment applications. We will describe our novel double-heterodyne detection method [4] , used to decrease the detection noise, as well as experiments assessing quantitatively the sensitivity of the spectral pattern to crystal deformation [5] , [6] , application of electric field [7] and temperature fluctuations. We currently demonstrate a state-of-the-art laser frequency stability at 1.7 × 10 − 15 at 1s [4] , limited by the latter effect, for which improvement strategies have been demonstrated elsewhere [2] and which we are currently implementing. The other effects which we have quantitatively studied are compatible with a few 10 − 18 frequency stability at 1s time scale. This work is particularly promising in the context of optical frequency lattice clocks, for which the ultra-stable laser used for probing the clock transition is a strong limiting factor of the frequency stability.
Here we report on the status of the Spectral-Hole Burning (SHB) laser-stabilization experiment at LNE-SYRTE, focusing on our first measurements of thermally induced frequency shifts of spectral holes at dilution temperatures (T0 < 1 K). The effect, which is predicated to scale as T 4 , produces shifts of order 1-10 Hz over its ≈ 517 THz center at these temperatures. To meet this challenge, we introduced a novel temperaturemodulation based approach to spectral-hole line shift measurements, allowing integration time of the small signals. We find a preliminary value for the line-shift constant of Eu 3+ :Y2SiO5, α = 107 Hz K-4 , a first at dilution temperatures.
Several properties of Eu 3+ :Y 2 SiO 5 spectral holes are measured, to assess the suitability of broad-band hole-patterns for use as laser-frequency references. We measure frequency shifts due to magnetic fields, side-features of neighboring spectral holes and changing optical probe power. A precise calibration of a temperature insensitive point is also performed, where the temperature-induced frequency shift is canceled to first order by the pressure-induced shift from the crystal's helium-gas environment.
Using an ultrastable continuous-wave laser at 580 nm we performed spectral hole burning of Eu(3+):Y(2)SiO(5) at a very high spectral resolution. The essential parameters determining the usefulness as a macroscopic frequency reference, linewidth, temperature sensitivity, and long-term stability, were characterized using a H-maser stabilized frequency comb. Spectral holes with a linewidth as low as 6 kHz were observed and the upper limit of the drift of the hole frequency was determined to be 5±3 mHz/s. We discuss the necessary requirements for achieving ultrahigh stability in laser frequency stabilization to these spectral holes.