Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Detection Techniques and Fundamental Limits in Frequency Stabilization via Spectral Hole Burning

Michael Hartman, Xiuji Lin, Benjamin Pointard, Rodolphe Le Targat, Signe Louise Seidelin, Philippe Goldner, Bess Fang, Yann Le Coq

Published Nov 8, 2023• 0 citations
OpenAlex

Abstract

This poster presents the status of the development of an ultra-frequency stable laser via a spectroscopic technique known as Spectral Hole Burning (SHB). In short, we can use a pump laser to imprint, or ’burn’, transmissive spectral lines, or ’spectral holes’, in the otherwise inhomogeneously broadened absorptive spectral sites of a Eu3+ doped Y2SiO5 crystal. We can then lock a probe laser to these narrow spectral features achieving our frequency stabilized laser. Of great concern is the frequency stability of the spectral holes, such as their sensitivity to temperature changes which we characterize here. Additionally, a challenge this experiment faces is the restriction of probe laser power to avoid damaging the spectral features. This sets a relatively high level of shot noise, limiting the detection sensitivity. Here we present our solution to overcome this difficulty by using a multi-spectral- hole probing scheme to average the probing signals of several burned spectral holes.

Related papers

Sub-Kelvin Spectral Hole Burning in Eu:YSO for Laser Frequency Stabilisation

A Robbes, Y Yuan, Philippe Goldner +4 more

As basic building blocks for quantum devices, ultra-stable lasers have a profound impact on various fields. Longer laser coherence times enhance the performance of quantum sensors, computers, communications, and optical clocks. Although optical lattice clocks have accomplished significant high-precision measurements, they often fall short of their quantum projection noise limits due to dead times during atom preparation: the instability in the laser frequency introduces stochastic fluctuations during the interrogation of atomic transitions (Dick effect). High-resolution optical clock comparisons are crucial for evaluating their accuracy and could lead to a redefinition of the SI second based on optical transitions [1].However, the most common technique for achieving ultra-stable lasers, the Pound-Drever-Hall method with Fabry-Perot cavities, faces thermal noise limitations of the cavities. To overcome these constraints, alternative methods such as Spectral Hole Burning (SHB) in rare-earth-doped crystals (REICs) have been explored. Indeed, REICs experience inhomogeneous broadening due to local lattice distortions caused by the size difference between dopant and host ions. An SHB protocol, which creates narrow spectral features through selective depletion of specific dopant ion populations using narrow-linewidth lasers, allows to overcome the inhomogeneous broadening and fully exploit the coherence of rare-earth ions. At cryogenic temperatures, Eu:YSO crystal exhibit persistent Spectral Holes a few kHz narrow and with a lifetime up to 10 h, at 4 K [2], making it a high-precision frequency reference, ideal for intermediate-timescale sensing.We report recent experimental progress on SHB in Eu:YSO crystals at specific sub-K dilution temperature setpoints that cancel the thermal sensitivity of the hole frequency [3]. The latest recorded performances on our experiment reach a fractional frequency stability of 4.10-16 at 1 s [4], which is close to the perfomance of our reference cavity at LTE. Therefore, a second SHB setup is needed for our future stability comparisons. On one front, we rationalize our SHB protocol and investigate new optimal burning parameters as well as test various doping concentrations to achieve the narrowest possible spectral holes on both setups. On another, we continue to further improving the laser frequency lock onto spectral holes, by cancelling as many systematic noise sources as possible. We provide the performances of our Michelson interferometer to reject frequency noise induced on light propagation to the crystal and by the cryostat acoustic vibrations. In addition, we explore a group delay measurement technique via phase modulation to enhance the precision on the pointing of the center of spectral holes. This should help removing slow frequency drifts due to asymmetric burning of the hole while it is probed by the laser.

•Sep 16, 2025•0 citations

Thermal-noise limits to the frequency stability of burned spectral holes

M. T. Hartman, N. Wagner, S. Kroker +2 more

Techniques in frequency stabilization of lasers to fixed-spacer optical cavities have advanced to the point where the ultimate frequency stabilities are limited by thermal noise for standard cavity configurations at room temperature. In early experiments, laser stabilization via spectral-hole burning (SHB) has been shown to be a promising alternative. In this Letter, we explore the thermal-noise limits to frequency stability in spectral holes and compile known material parameters for a typical system used in SHB experiments (Eu3+ doped Y2SiO5) to make numerical estimates for the fundamental thermal-noise induced frequency instability in spectral holes for the liquid-helium temperature and dilution temperature cases. These efforts can guide the design of future SHB experiments and clarify which important material parameters remain to be measured.

arXiv:2412.08665•Applied Physics Letters•Jul 14, 2025•5 citations

Spectral Hole Burning for Ultra-stable Lasers

Shuo Zhang, Nemanja Lučić, Nicolas Galland +6 more

Spectral hole burning in rare earth doped crystal can provide frequency references based on the optical transition of the dopant ions [1] . The narrow spectral patterns can be used to improve laser frequency stabilization [2] , [3] and provide a new generation of ultra-stable lasers with lower thermal noise benefiting from the cryogenic environment and better quality factor of the crystal than the amorphous glass typically used in the Fabry-Perot cavity. We utilize Europium doped yttrium silicon oxide (Eu:YSO) in our experiments, which allow realization of long lived (hours or more depending on temperature) narrow spectral holes ( kHz or less) well suited for high precision experiment applications. We will describe our novel double-heterodyne detection method [4] , used to decrease the detection noise, as well as experiments assessing quantitatively the sensitivity of the spectral pattern to crystal deformation [5] , [6] , application of electric field [7] and temperature fluctuations. We currently demonstrate a state-of-the-art laser frequency stability at 1.7 × 10 − 15 at 1s [4] , limited by the latter effect, for which improvement strategies have been demonstrated elsewhere [2] and which we are currently implementing. The other effects which we have quantitatively studied are compatible with a few 10 − 18 frequency stability at 1s time scale. This work is particularly promising in the context of optical frequency lattice clocks, for which the ultra-stable laser used for probing the clock transition is a strong limiting factor of the frequency stability.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 21, 2021•2 citations

Frequency locking a laser on a spectral hole pattern with a multi-channel heterodyne method using SDR and GnuRadio

Nicolas Galland, Nemanja Lučić, Héctor Álvarez Martínez +7 more

High precision spectroscopic probing of a narrow spectral hole pattern imprinted in the inhom-geneously broadened absorption spectrum of Eu3+: Y2SiO5 crystal can be used to stabilize a laser frequency. A multi-hole pattern can be burn and all the holes can be probed simultaneously using a multiple frequency signal. The dispersion induced dephasing acquired by the light through the crystal is measured to derive an error signal suitable to lock the laser frequency to the spectral hole pattern. An Ettus USRP X310 driven by a python program based on GNU Radio is used for both generating the multiple frequency signal and to compute the correction applied to the laser frequency.

•Jan 1, 2019•0 citations

Laser stabilization at 1536 nm using regenerative spectral hole burning

Peter B. Sellin, Nick Strickland, Thomas Böttger +2 more

Laser frequency stabilization giving a 500-Hz Allan deviation for a 2-ms integration time with drift reduced to 7 kHz/min over several minutes was achieved at 1536 nm in the optical communication band. A continuously regenerated spectral hole in the inhomogeneously broadened ${}^{4}{I}_{15/2}{(1)}^{4}{I}_{13/2}(1)$ optical absorption of an ${\mathrm{Er}}^{3+}:{\mathrm{Y}}_{2}{\mathrm{SiO}}_{5}$ crystal was used as the short-term frequency reference, while a variation on the locking technique allowed simultaneous use of the inhomogeneously broadened absorption line as a long-term reference. The reported frequency stability was achieved without vibration isolation. Spectral hole burning frequency stabilization provides ideal laser sources for high-resolution spectroscopy, real-time optical signal processing, and a range of applications requiring ultra-narrow-band light sources or coherent detection; the time scale for stability and the compatibility with spectral hole burning devices make this technique complementary to other frequency references for laser stabilization.

Physical review. B, Condensed matter•Mar 30, 2001•54 citations

Burning and reading ensembles of spectral holes by optical frequency combs: Demonstration in rare-earth-doped solids and application to laser frequency stabilization

René Oswald, Alexander Yu. Nevsky, Stephan Schiller

We describe a spectroscopic method applicable to inhomogeneously broadened transitions. As a test system we use suitable rare-earth-doped solids in which persistent spectral holes can be burned on weakly allowed electronic transitions. These systems are of interest as frequency references for the stabilization of laser frequencies. In all experiments so far, spectral holes are burned and read out individually. Here we present a demonstration of simultaneous burning and readout of sets of spectral holes, containing up to 1024 individual spectral holes, by a comb of laser frequencies. The simultaneous readout of such a set leads to an effective compound signal that has a higher signal-to-noise ratio. Here, an improvement by a factor of 20 was obtained for a set of 512 spectral holes. We use the method to stabilize the frequency of a laser and characterize its stability.

Physical Review A•Dec 13, 2021•6 citations
This poster presents the status of the development of an ultra-frequency stable laser via a spectroscopic technique known as Spectral Hole Burning (SHB). In short, we can use a pump laser to imprint, or ’burn’, transmissive spectral lines, or ’spectral holes’, in the otherwise inhomogeneously broadened absorptive spectral sites of a Eu3+ doped Y2SiO5 crystal. We can then lock a probe laser to these narrow spectral features achieving our frequency stabilized laser. Of great concern is the frequency stability of the spectral holes, such as their sensitivity to temperature changes which we characterize here. Additionally, a challenge this experiment faces is the restriction of probe laser power to avoid damaging the spectral features. This sets a relatively high level of shot noise, limiting the detection sensitivity. Here we present our solution to overcome this difficulty by using a multi-spectral- hole probing scheme to average the probing signals of several burned spectral holes.
As basic building blocks for quantum devices, ultra-stable lasers have a profound impact on various fields. Longer laser coherence times enhance the performance of quantum sensors, computers, communications, and optical clocks. Although optical lattice clocks have accomplished significant high-precision measurements, they often fall short of their quantum projection noise limits due to dead times during atom preparation: the instability in the laser frequency introduces stochastic fluctuations during the interrogation of atomic transitions (Dick effect). High-resolution optical clock comparisons are crucial for evaluating their accuracy and could lead to a redefinition of the SI second based on optical transitions [1].However, the most common technique for achieving ultra-stable lasers, the Pound-Drever-Hall method with Fabry-Perot cavities, faces thermal noise limitations of the cavities. To overcome these constraints, alternative methods such as Spectral Hole Burning (SHB) in rare-earth-doped crystals (REICs) have been explored. Indeed, REICs experience inhomogeneous broadening due to local lattice distortions caused by the size difference between dopant and host ions. An SHB protocol, which creates narrow spectral features through selective depletion of specific dopant ion populations using narrow-linewidth lasers, allows to overcome the inhomogeneous broadening and fully exploit the coherence of rare-earth ions. At cryogenic temperatures, Eu:YSO crystal exhibit persistent Spectral Holes a few kHz narrow and with a lifetime up to 10 h, at 4 K [2], making it a high-precision frequency reference, ideal for intermediate-timescale sensing.We report recent experimental progress on SHB in Eu:YSO crystals at specific sub-K dilution temperature setpoints that cancel the thermal sensitivity of the hole frequency [3]. The latest recorded performances on our experiment reach a fractional frequency stability of 4.10-16 at 1 s [4], which is close to the perfomance of our reference cavity at LTE. Therefore, a second SHB setup is needed for our future stability comparisons. On one front, we rationalize our SHB protocol and investigate new optimal burning parameters as well as test various doping concentrations to achieve the narrowest possible spectral holes on both setups. On another, we continue to further improving the laser frequency lock onto spectral holes, by cancelling as many systematic noise sources as possible. We provide the performances of our Michelson interferometer to reject frequency noise induced on light propagation to the crystal and by the cryostat acoustic vibrations. In addition, we explore a group delay measurement technique via phase modulation to enhance the precision on the pointing of the center of spectral holes. This should help removing slow frequency drifts due to asymmetric burning of the hole while it is probed by the laser.
Techniques in frequency stabilization of lasers to fixed-spacer optical cavities have advanced to the point where the ultimate frequency stabilities are limited by thermal noise for standard cavity configurations at room temperature. In early experiments, laser stabilization via spectral-hole burning (SHB) has been shown to be a promising alternative. In this Letter, we explore the thermal-noise limits to frequency stability in spectral holes and compile known material parameters for a typical system used in SHB experiments (Eu3+ doped Y2SiO5) to make numerical estimates for the fundamental thermal-noise induced frequency instability in spectral holes for the liquid-helium temperature and dilution temperature cases. These efforts can guide the design of future SHB experiments and clarify which important material parameters remain to be measured.
Spectral hole burning in rare earth doped crystal can provide frequency references based on the optical transition of the dopant ions [1] . The narrow spectral patterns can be used to improve laser frequency stabilization [2] , [3] and provide a new generation of ultra-stable lasers with lower thermal noise benefiting from the cryogenic environment and better quality factor of the crystal than the amorphous glass typically used in the Fabry-Perot cavity. We utilize Europium doped yttrium silicon oxide (Eu:YSO) in our experiments, which allow realization of long lived (hours or more depending on temperature) narrow spectral holes ( kHz or less) well suited for high precision experiment applications. We will describe our novel double-heterodyne detection method [4] , used to decrease the detection noise, as well as experiments assessing quantitatively the sensitivity of the spectral pattern to crystal deformation [5] , [6] , application of electric field [7] and temperature fluctuations. We currently demonstrate a state-of-the-art laser frequency stability at 1.7 × 10 − 15 at 1s [4] , limited by the latter effect, for which improvement strategies have been demonstrated elsewhere [2] and which we are currently implementing. The other effects which we have quantitatively studied are compatible with a few 10 − 18 frequency stability at 1s time scale. This work is particularly promising in the context of optical frequency lattice clocks, for which the ultra-stable laser used for probing the clock transition is a strong limiting factor of the frequency stability.
High precision spectroscopic probing of a narrow spectral hole pattern imprinted in the inhom-geneously broadened absorption spectrum of Eu3+: Y2SiO5 crystal can be used to stabilize a laser frequency. A multi-hole pattern can be burn and all the holes can be probed simultaneously using a multiple frequency signal. The dispersion induced dephasing acquired by the light through the crystal is measured to derive an error signal suitable to lock the laser frequency to the spectral hole pattern. An Ettus USRP X310 driven by a python program based on GNU Radio is used for both generating the multiple frequency signal and to compute the correction applied to the laser frequency.
Laser frequency stabilization giving a 500-Hz Allan deviation for a 2-ms integration time with drift reduced to 7 kHz/min over several minutes was achieved at 1536 nm in the optical communication band. A continuously regenerated spectral hole in the inhomogeneously broadened 4I15/2(1)4I13/2(1){}^{4}{I}_{15/2}{(1)}^{4}{I}_{13/2}(1)4I15/2​(1)4I13/2​(1) optical absorption of an Er3+:Y2SiO5{\mathrm{Er}}^{3+}:{\mathrm{Y}}_{2}{\mathrm{SiO}}_{5}Er3+:Y2​SiO5​ crystal was used as the short-term frequency reference, while a variation on the locking technique allowed simultaneous use of the inhomogeneously broadened absorption line as a long-term reference. The reported frequency stability was achieved without vibration isolation. Spectral hole burning frequency stabilization provides ideal laser sources for high-resolution spectroscopy, real-time optical signal processing, and a range of applications requiring ultra-narrow-band light sources or coherent detection; the time scale for stability and the compatibility with spectral hole burning devices make this technique complementary to other frequency references for laser stabilization.
We describe a spectroscopic method applicable to inhomogeneously broadened transitions. As a test system we use suitable rare-earth-doped solids in which persistent spectral holes can be burned on weakly allowed electronic transitions. These systems are of interest as frequency references for the stabilization of laser frequencies. In all experiments so far, spectral holes are burned and read out individually. Here we present a demonstration of simultaneous burning and readout of sets of spectral holes, containing up to 1024 individual spectral holes, by a comb of laser frequencies. The simultaneous readout of such a set leads to an effective compound signal that has a higher signal-to-noise ratio. Here, an improvement by a factor of 20 was obtained for a set of 512 spectral holes. We use the method to stabilize the frequency of a laser and characterize its stability.