Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1301.3184 · Superconductor Science and Technology

A dispersive nanoSQUID magnetometer for ultra-low noise, high bandwidth flux detection

Eli M. Levenson-Falk, Rajamani Vijay, Natania Antler, Irfan A. Siddiqi

Published Apr 4, 2013• 41 citations
arXivHTMLPDF

Abstract

We describe a dispersive nanoSQUID (nanoscale superconducting quantum interference device) magnetometer comprised of two variable thickness aluminum weak-link Josephson junctions shunted in parallel with an on-chip capacitor. This arrangement forms a nonlinear oscillator with a tunable 4–8 GHz resonant frequency with a quality factor Q = 30 when coupled directly to a 50 Ω transmission line. In the presence of a near-resonant microwave carrier signal, a low frequency flux input generates sidebands that are readily detected using microwave reflectometry. If the carrier excitation is sufficiently strong, then the magnetometer also exhibits parametric gain, resulting in a minimum effective flux noise of 30 n Φ 0 Hz −1/2 with 20 MHz of instantaneous bandwidth. If the magnetometer is followed with a near-quantum-noise-limited Josephson parametric amplifier, we can increase the bandwidth to 60 MHz without compromising sensitivity. This combination of high sensitivity and wide bandwidth with no on-chip dissipation makes this device ideal for local sensing of spin dynamics, both classical and quantum.

DOI
10.1088/0953-2048/26/5/055015

Related papers

Dispersive magnetometry with a quantum limited SQUID parametric amplifier

Michael J. Hatridge, Rajamani Vijay, D. H. Slichter +2 more

There is currently fundamental and technological interest in measuring and manipulating nanoscale magnets, particularly in the quantum coherent regime. To observe the dynamics of such systems one requires a magnetometer with not only exceptional sensitivity but also high gain, wide bandwidth, and low backaction. We demonstrate a dispersive magnetometer consisting of a two-junction superconducting quantum interference device (SQUID) in parallel with an integrated, lumped-element capacitor. Input flux signals are encoded as a phase modulation of the microwave drive tone applied to the magnetometer, resulting in a single quadrature voltage signal. For strong drive power, the nonlinearity of the resonator results in quantum limited, phase sensitive parametric amplification of this signal, which improves flux sensitivity at the expense of bandwidth. Depending on the drive parameters, the device performance ranges from an effective flux noise of 0.29 $\ensuremath{\mu}{\ensuremath{\Phi}}_{0}$Hz${}^{\ensuremath{-}1/2}$ and 20 MHz of signal bandwidth to a noise of 0.14 $\ensuremath{\mu}{\ensuremath{\Phi}}_{0}$Hz${}^{\ensuremath{-}1/2}$ and a bandwidth of 0.6 MHz. These results are in excellent agreement with our theoretical model.

arXiv:1003.2466•Physical Review B•Apr 4, 2011•270 citations

Dispersive nanoSQUID magnetometry

Eli M. Levenson-Falk, Natania Antler, Irfan A. Siddiqi

Abstract We describe the theory and implementation of a dispersive magnetometer based on an aluminum nanoSQUID. The nanoSQUID consists of a superconducting loop interrupted by two variable-thickness weak-link nanobridge Josephson junctions. When the nanoSQUID is placed in parallel with a lumped-element capacitor, it acts as the inductive element in a resonant tank circuit. By performing microwave reflectometry on the circuit, the SQUID inductance can be measured, providing a sensitive meter of the flux threading the SQUID loop. In this review we provide the theoretical basis for the device, describe design and operation considerations, and present characterization results on several devices.

Superconductor Science and Technology•Sep 26, 2016•19 citations

Nonlinear microwave response of aluminum weak-link Josephson oscillators

Eli M. Levenson-Falk, R. Vijay, I. Siddiqi

We present the driven response at T=30 mK of 6 GHz superconducting resonators constructed from capacitively-shunted three-dimensional (3D) aluminum nanobridge superconducting quantum interference devices (nanoSQUIDs). We observe flux modulation of the resonant frequency in quantitative agreement with numerical calculation and characteristic of near-ideal short weak-link junctions. Under strong microwave excitation, we observe stable bifurcation in devices with coupled quality factor (Q) ranging from 30–3500. Near this bias point, parametric amplification with >20 dB gain, 40 MHz bandwidth, and near quantum-limited noise performance is observed. Our results indicate that 3D nanobridge junctions are attractive circuit elements to realize quantum bits.

arXiv:1101.4672•Applied Physics Letters•Mar 21, 2011•37 citations

In-plane magnetic field tolerance of a dispersive aluminum nanobridge SQUID magnetometer

N. Antler, Eli M. Levenson-Falk, R. Naik +4 more

We characterize the flux sensitivity of a dispersive 3D aluminum nanobridge superconducting quantum interference device (SQUID) magnetometer as a function of applied in-plane magnetic field. In zero field, we observe an effective flux noise of 17 nΦ0/Hz1/2 with 25 MHz of bandwidth at 150 mK. Flux noise increased by less than a factor of three with parallel magnetic fields up to 61 mT. Operation in higher fields may be possible by decreasing the dimensions of the shunt capacitor in the magnetometer circuit. These devices are thus well suited for observing high-speed dynamics in nanoscale magnets, even in the presence of moderate bias magnetic fields.

arXiv:1303.2737•Applied Physics Letters•Jun 10, 2013•19 citations

Static and Microwave Transport Properties of Aluminum Nanobridge Josephson Junctions

Eli M. Levenson-Falk

Josephson junctions are the basis of superconducting qubits, amplifiers, and magnetometers. Historically, tunnel-style junctions have been most common. However, for some applications--those requiring a small, highly transparent, all-superconducting junction--nanobridge weak link junctions may be preferable. This thesis presents extensive characterization of aluminum nanobridge Josephson junctions. The junction behavior is simulated by numerically solving the Usadel equations. These simulations are then tested and confirmed via low- and microwave-frequency transport measurements. The data confirm that nanobridge junctions approach the ideal weak-link Josephson limit.Such a near-ideal junction can be used in a superconducting quantum interference device (SQUID) to form an ultra sensitive magnetometer. This thesis presents the first nanobridge-based dispersive SQUID magnetometer. The devices show near-zero dissipation, with bandwidth and sensitivity on par with the best reported results for any SQUID-based magnetometer. These magnetometers have several flexible modes of operation, allowing for optimization of sensitivity, bandwidth, or backaction. They also provide insight into the internal dynamics of dispersive measurement with nonlinear cavities, as the magnetometer backaction depends on the bias point and can readily be measured.Nanobridge junctions also provide a useful tool for diagnosing sources of decoherence in superconducting qubits. By replacing the usual tunnel junction with a nanobridge, the contribution of the junction to decoherence processes may be probed. In particular, the interaction of nanobridge junctions with quasiparticles provides information both about the junctions themselves and about quasiparticle generation and relaxation mechanisms. This thesis reports measurements of nonequilibrium quasiparticles trapping in phase-biased nanobridge junctions. By probing the quasiparticle-induced changes in resonant frequency of a high-Q nanoSQUID oscillator, one may measure the mean distribution of trapped quasiparticles and study its temperature dependence. These measurements also provide spectroscopy of the junctions' internal Andreev states and the dynamics of quasiparticle excitation and retrapping. The work presented here demonstrates the utility of nanobridge junctions as a tool for quantifying the population and distribution of quasiparticles in a superconducting circuit.

•Jan 1, 2013•1 citation

Optimization of superconducting flux qubit readout using near-quantum-limited amplifiers

Jedediah E Johnson

Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.

•Jan 1, 2012•2 citations
We describe a dispersive nanoSQUID (nanoscale superconducting quantum interference device) magnetometer comprised of two variable thickness aluminum weak-link Josephson junctions shunted in parallel with an on-chip capacitor. This arrangement forms a nonlinear oscillator with a tunable 4–8 GHz resonant frequency with a quality factor Q = 30 when coupled directly to a 50 Ω transmission line. In the presence of a near-resonant microwave carrier signal, a low frequency flux input generates sidebands that are readily detected using microwave reflectometry. If the carrier excitation is sufficiently strong, then the magnetometer also exhibits parametric gain, resulting in a minimum effective flux noise of 30 n Φ 0 Hz −1/2 with 20 MHz of instantaneous bandwidth. If the magnetometer is followed with a near-quantum-noise-limited Josephson parametric amplifier, we can increase the bandwidth to 60 MHz without compromising sensitivity. This combination of high sensitivity and wide bandwidth with no on-chip dissipation makes this device ideal for local sensing of spin dynamics, both classical and quantum.
There is currently fundamental and technological interest in measuring and manipulating nanoscale magnets, particularly in the quantum coherent regime. To observe the dynamics of such systems one requires a magnetometer with not only exceptional sensitivity but also high gain, wide bandwidth, and low backaction. We demonstrate a dispersive magnetometer consisting of a two-junction superconducting quantum interference device (SQUID) in parallel with an integrated, lumped-element capacitor. Input flux signals are encoded as a phase modulation of the microwave drive tone applied to the magnetometer, resulting in a single quadrature voltage signal. For strong drive power, the nonlinearity of the resonator results in quantum limited, phase sensitive parametric amplification of this signal, which improves flux sensitivity at the expense of bandwidth. Depending on the drive parameters, the device performance ranges from an effective flux noise of 0.29 $\ensuremath{\mu}{\ensuremath{\Phi}}_{0}$Hz${}^{\ensuremath{-}1/2}$ and 20 MHz of signal bandwidth to a noise of 0.14 $\ensuremath{\mu}{\ensuremath{\Phi}}_{0}$Hz${}^{\ensuremath{-}1/2}$ and a bandwidth of 0.6 MHz. These results are in excellent agreement with our theoretical model.
Abstract We describe the theory and implementation of a dispersive magnetometer based on an aluminum nanoSQUID. The nanoSQUID consists of a superconducting loop interrupted by two variable-thickness weak-link nanobridge Josephson junctions. When the nanoSQUID is placed in parallel with a lumped-element capacitor, it acts as the inductive element in a resonant tank circuit. By performing microwave reflectometry on the circuit, the SQUID inductance can be measured, providing a sensitive meter of the flux threading the SQUID loop. In this review we provide the theoretical basis for the device, describe design and operation considerations, and present characterization results on several devices.
We present the driven response at T=30 mK of 6 GHz superconducting resonators constructed from capacitively-shunted three-dimensional (3D) aluminum nanobridge superconducting quantum interference devices (nanoSQUIDs). We observe flux modulation of the resonant frequency in quantitative agreement with numerical calculation and characteristic of near-ideal short weak-link junctions. Under strong microwave excitation, we observe stable bifurcation in devices with coupled quality factor (Q) ranging from 30–3500. Near this bias point, parametric amplification with >20 dB gain, 40 MHz bandwidth, and near quantum-limited noise performance is observed. Our results indicate that 3D nanobridge junctions are attractive circuit elements to realize quantum bits.
We characterize the flux sensitivity of a dispersive 3D aluminum nanobridge superconducting quantum interference device (SQUID) magnetometer as a function of applied in-plane magnetic field. In zero field, we observe an effective flux noise of 17 nΦ0/Hz1/2 with 25 MHz of bandwidth at 150 mK. Flux noise increased by less than a factor of three with parallel magnetic fields up to 61 mT. Operation in higher fields may be possible by decreasing the dimensions of the shunt capacitor in the magnetometer circuit. These devices are thus well suited for observing high-speed dynamics in nanoscale magnets, even in the presence of moderate bias magnetic fields.
Josephson junctions are the basis of superconducting qubits, amplifiers, and magnetometers. Historically, tunnel-style junctions have been most common. However, for some applications--those requiring a small, highly transparent, all-superconducting junction--nanobridge weak link junctions may be preferable. This thesis presents extensive characterization of aluminum nanobridge Josephson junctions. The junction behavior is simulated by numerically solving the Usadel equations. These simulations are then tested and confirmed via low- and microwave-frequency transport measurements. The data confirm that nanobridge junctions approach the ideal weak-link Josephson limit.Such a near-ideal junction can be used in a superconducting quantum interference device (SQUID) to form an ultra sensitive magnetometer. This thesis presents the first nanobridge-based dispersive SQUID magnetometer. The devices show near-zero dissipation, with bandwidth and sensitivity on par with the best reported results for any SQUID-based magnetometer. These magnetometers have several flexible modes of operation, allowing for optimization of sensitivity, bandwidth, or backaction. They also provide insight into the internal dynamics of dispersive measurement with nonlinear cavities, as the magnetometer backaction depends on the bias point and can readily be measured.Nanobridge junctions also provide a useful tool for diagnosing sources of decoherence in superconducting qubits. By replacing the usual tunnel junction with a nanobridge, the contribution of the junction to decoherence processes may be probed. In particular, the interaction of nanobridge junctions with quasiparticles provides information both about the junctions themselves and about quasiparticle generation and relaxation mechanisms. This thesis reports measurements of nonequilibrium quasiparticles trapping in phase-biased nanobridge junctions. By probing the quasiparticle-induced changes in resonant frequency of a high-Q nanoSQUID oscillator, one may measure the mean distribution of trapped quasiparticles and study its temperature dependence. These measurements also provide spectroscopy of the junctions' internal Andreev states and the dynamics of quasiparticle excitation and retrapping. The work presented here demonstrates the utility of nanobridge junctions as a tool for quantifying the population and distribution of quasiparticles in a superconducting circuit.
Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.