Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Static and Microwave Transport Properties of Aluminum Nanobridge Josephson Junctions

Eli M. Levenson-Falk

Published Jan 1, 2013• 1 citation
OpenAlex

Abstract

Josephson junctions are the basis of superconducting qubits, amplifiers, and magnetometers. Historically, tunnel-style junctions have been most common. However, for some applications--those requiring a small, highly transparent, all-superconducting junction--nanobridge weak link junctions may be preferable. This thesis presents extensive characterization of aluminum nanobridge Josephson junctions. The junction behavior is simulated by numerically solving the Usadel equations. These simulations are then tested and confirmed via low- and microwave-frequency transport measurements. The data confirm that nanobridge junctions approach the ideal weak-link Josephson limit.Such a near-ideal junction can be used in a superconducting quantum interference device (SQUID) to form an ultra sensitive magnetometer. This thesis presents the first nanobridge-based dispersive SQUID magnetometer. The devices show near-zero dissipation, with bandwidth and sensitivity on par with the best reported results for any SQUID-based magnetometer. These magnetometers have several flexible modes of operation, allowing for optimization of sensitivity, bandwidth, or backaction. They also provide insight into the internal dynamics of dispersive measurement with nonlinear cavities, as the magnetometer backaction depends on the bias point and can readily be measured.Nanobridge junctions also provide a useful tool for diagnosing sources of decoherence in superconducting qubits. By replacing the usual tunnel junction with a nanobridge, the contribution of the junction to decoherence processes may be probed. In particular, the interaction of nanobridge junctions with quasiparticles provides information both about the junctions themselves and about quasiparticle generation and relaxation mechanisms. This thesis reports measurements of nonequilibrium quasiparticles trapping in phase-biased nanobridge junctions. By probing the quasiparticle-induced changes in resonant frequency of a high-Q nanoSQUID oscillator, one may measure the mean distribution of trapped quasiparticles and study its temperature dependence. These measurements also provide spectroscopy of the junctions' internal Andreev states and the dynamics of quasiparticle excitation and retrapping. The work presented here demonstrates the utility of nanobridge junctions as a tool for quantifying the population and distribution of quasiparticles in a superconducting circuit.

Related papers

Continuous real-time detection of quasiparticle trapping in aluminum nanobridge Josephson junctions

J. T. Farmer, A. Zarassi, D. M. Hartsell +3 more

Nonequilibrium quasiparticles are ubiquitous in superconducting electronics. These quasiparticles can trap in the internal Andreev bound states of a phase-biased Josephson junction, providing a mechanism for studying their presence and behavior. We characterize a quasiparticle trapping detector device based on a two junction aluminum nanobridge superconducting quantum interference device incorporated into a transmission line resonator. When the device is flux-biased, distinct resonant frequencies develop depending on the trapped quasiparticle number. We demonstrate continuous detection of up to 3 trapped quasiparticles, with detection of a trapped quasiparticle with a signal-to-noise ratio of 27 in 5 μs. We describe initial measurements of quasiparticle behavior and discuss the possible optimization and application of such detector devices.

arXiv:2107.07125•Applied Physics Letters•Sep 20, 2021•6 citations

Nanobridge superconducting quantum interference devices: Beyond the Josephson limit

Dibyendu Hazra

Nanoscale superconducting quantum interference devices (nano-SQUIDS) where the weak links are made from nanobridges, i.e., nanobridge SQUIDs (NBSs), are one of the most sensitive magnetometers for nanoscale magnetometry. Because of very strong nonlinearity in the nanobridge-electrode joints, the applied magnetic flux (${\mathrm{\ensuremath{\Phi}}}_{a}$)--critical current (${I}_{c}$) characteristics of NBSs differ very significantly from conventional tunnel-junction SQUIDs, especially when the nanobridges are long and/or the screening parameter is large. However, in most of the theoretical descriptions, NBSs have been treated as the conventional tunnel-junction SQUIDs, which are based on the dc Josephson effect. Here, I present a model demonstrating that for long nanobridges and/or large screening parameters the ${I}_{c}({\mathrm{\ensuremath{\Phi}}}_{a})$ of a NBS can be explained by merely considering the fluxoid quantization in the NBS loop and the energy of the NBS; it is not necessary to take the Josephson effect into consideration. I also demonstrate that using the model, one can derive useful expressions such as the modulation depth and transfer function. I discuss the role of the kinetic inductance fraction ($\ensuremath{\kappa}$) in determining ${I}_{c}({\mathrm{\ensuremath{\Phi}}}_{a})$. I compare the predictions of the present model with the experimental data already published by several groups.

arXiv:1809.09510•Physical review. B./Physical review. B•Apr 5, 2019•11 citations

Superconducting Nanobridge SQUID Magnetometers for Spin Sensing

Natania Antler

Author(s): Antler, Natania | Advisor(s): Siddiqi, Irfan | Abstract: As the cutting edge of science and technology pushes towards smaller length scales, sensing technologies with nanoscale precision become increasingly important. In this thesis I will discuss the optimization and application of a 3D nanobridge SQUID magnetometer for studying solid state spin systems, in particular for sensing impurity spins in diamond. Solid state spins have proposed applications in memory and computation for both classical and quantum computing. Isolated spins typically have longer coherence times, making them attractive qubit candidates, but necessitating the development of very sensitive detectors for readout. This 3D nanobridge SQUID combines the exquisite spatial sensitivity of a traditional nanoSQUID with a large non-linearity on par with a tunnel junction SQUID. This allows us to build a highly sensitive magnetometer which can act as both an efficient flux transducer as well as a nearly quantum limited lumped Josephson Parametric Amplifier. We show that the device has a minimum flux noise of 17 ± 0.9 nΦ0/Hz1/2 with only a factor of ∼2.5 increase in flux noise up to 61 mT. A second generation device with a smaller capacitor achieves field tolerance up to 75 mT. The maximal bandwidth values range from 25-40 MHz in the parametric amplification regime to 70 MHz in the linear regime. This combination of large bandwidth, low flux noise, large flux coupling and field tolerance make this sensor a promising candidate for near-single-spin dynamics measurements.In the last part of this thesis we begin to demonstrate the utility of a nanobridge SQUID magnetometer for characterizing spin systems in the solid state. We use the magnetometer to measure the decay characteristics of P1 centers in diamond. We find that the spin-lattice relaxation time varies with temperature, with an order of magnitude decrease in the decay time between 25 mK and 370 mK.

•Jan 1, 2014•0 citations

Dispersive nanoSQUID magnetometry

Eli M. Levenson-Falk, Natania Antler, Irfan A. Siddiqi

Abstract We describe the theory and implementation of a dispersive magnetometer based on an aluminum nanoSQUID. The nanoSQUID consists of a superconducting loop interrupted by two variable-thickness weak-link nanobridge Josephson junctions. When the nanoSQUID is placed in parallel with a lumped-element capacitor, it acts as the inductive element in a resonant tank circuit. By performing microwave reflectometry on the circuit, the SQUID inductance can be measured, providing a sensitive meter of the flux threading the SQUID loop. In this review we provide the theoretical basis for the device, describe design and operation considerations, and present characterization results on several devices.

Superconductor Science and Technology•Sep 26, 2016•19 citations

A dispersive nanoSQUID magnetometer for ultra-low noise, high bandwidth flux detection

Eli M. Levenson-Falk, Rajamani Vijay, Natania Antler +1 more

We describe a dispersive nanoSQUID (nanoscale superconducting quantum interference device) magnetometer comprised of two variable thickness aluminum weak-link Josephson junctions shunted in parallel with an on-chip capacitor. This arrangement forms a nonlinear oscillator with a tunable 4–8 GHz resonant frequency with a quality factor Q = 30 when coupled directly to a 50 Ω transmission line. In the presence of a near-resonant microwave carrier signal, a low frequency flux input generates sidebands that are readily detected using microwave reflectometry. If the carrier excitation is sufficiently strong, then the magnetometer also exhibits parametric gain, resulting in a minimum effective flux noise of 30 n Φ 0 Hz −1/2 with 20 MHz of instantaneous bandwidth. If the magnetometer is followed with a near-quantum-noise-limited Josephson parametric amplifier, we can increase the bandwidth to 60 MHz without compromising sensitivity. This combination of high sensitivity and wide bandwidth with no on-chip dissipation makes this device ideal for local sensing of spin dynamics, both classical and quantum.

arXiv:1301.3184•Superconductor Science and Technology•Apr 4, 2013•41 citations

Magnetometry by a proximity Josephson junction interferometer

Robab Najafi Jabdaraghi

In quantum technology, several aspects of superconductivity such as proximity effect have studied to develop a wide range of attractive applications at sub-kelvin temperatures. A new type of interferometer based on the proximity effect, taking place around transparent interfaces between normal- and superconducting metals, the Superconducting Quantum Interference Proximity Transistor (SQUIPT), relies on the phase dependence of the density of states in the proximized weak link. The SQUIPT devices offer the possibility to realize sensitive low-dissipation magnetometers compared to conventional DC SQUIDs. In this thesis, we investigate the development of the sensitive SQUIPT magnetometers. The first part of the thesis covers the characterization of non-hysteretic SQUIPTs with enhanced responsivity. In these structures, we demonstrate magnetic flux modulation of the device characteristics displaying no hysteresis at low temperatures by simply increasing the Josephson inductance of the weak link compared to self-inductance of the superconducting loop in the device. As a consequence, improvement in magnetic field responsivity is achievable. We then turn to the implementation of SQUIPT devices based on different fabrication methods and superconductor materials for improving the device performance. In this aspect, we fabricate and characterize niobium-based SNS devices utilizing two separate lithography and deposition steps with strong Ar ion cleaning in between. We further investigate a prototype hybrid SQUIPT device based on an Nb-Cu-Nb SNS junction with a conventional Al probe in tunnel junction. In the third part of the thesis, we present the flux noise characterization of a SQUIPT device using simultaneous measurement of DC transport properties and shot noise. To probe the noise, we use a cryogenic amplifier operating at frequencies in the range of a few MHz. We adapt this technique for flux noise measurements in SQUIPTs, adaptable also to low-temperature shot noise measurements of other nonlinear devices with high impedance. In order to investigate flux noise of SQUIPTs, we develop a model allowing one to optimize the figures of merit of the magnetometers such as the noise-equivalent flux.

•Feb 13, 2018•0 citations
Josephson junctions are the basis of superconducting qubits, amplifiers, and magnetometers. Historically, tunnel-style junctions have been most common. However, for some applications--those requiring a small, highly transparent, all-superconducting junction--nanobridge weak link junctions may be preferable. This thesis presents extensive characterization of aluminum nanobridge Josephson junctions. The junction behavior is simulated by numerically solving the Usadel equations. These simulations are then tested and confirmed via low- and microwave-frequency transport measurements. The data confirm that nanobridge junctions approach the ideal weak-link Josephson limit.Such a near-ideal junction can be used in a superconducting quantum interference device (SQUID) to form an ultra sensitive magnetometer. This thesis presents the first nanobridge-based dispersive SQUID magnetometer. The devices show near-zero dissipation, with bandwidth and sensitivity on par with the best reported results for any SQUID-based magnetometer. These magnetometers have several flexible modes of operation, allowing for optimization of sensitivity, bandwidth, or backaction. They also provide insight into the internal dynamics of dispersive measurement with nonlinear cavities, as the magnetometer backaction depends on the bias point and can readily be measured.Nanobridge junctions also provide a useful tool for diagnosing sources of decoherence in superconducting qubits. By replacing the usual tunnel junction with a nanobridge, the contribution of the junction to decoherence processes may be probed. In particular, the interaction of nanobridge junctions with quasiparticles provides information both about the junctions themselves and about quasiparticle generation and relaxation mechanisms. This thesis reports measurements of nonequilibrium quasiparticles trapping in phase-biased nanobridge junctions. By probing the quasiparticle-induced changes in resonant frequency of a high-Q nanoSQUID oscillator, one may measure the mean distribution of trapped quasiparticles and study its temperature dependence. These measurements also provide spectroscopy of the junctions' internal Andreev states and the dynamics of quasiparticle excitation and retrapping. The work presented here demonstrates the utility of nanobridge junctions as a tool for quantifying the population and distribution of quasiparticles in a superconducting circuit.
Nonequilibrium quasiparticles are ubiquitous in superconducting electronics. These quasiparticles can trap in the internal Andreev bound states of a phase-biased Josephson junction, providing a mechanism for studying their presence and behavior. We characterize a quasiparticle trapping detector device based on a two junction aluminum nanobridge superconducting quantum interference device incorporated into a transmission line resonator. When the device is flux-biased, distinct resonant frequencies develop depending on the trapped quasiparticle number. We demonstrate continuous detection of up to 3 trapped quasiparticles, with detection of a trapped quasiparticle with a signal-to-noise ratio of 27 in 5 μs. We describe initial measurements of quasiparticle behavior and discuss the possible optimization and application of such detector devices.
Nanoscale superconducting quantum interference devices (nano-SQUIDS) where the weak links are made from nanobridges, i.e., nanobridge SQUIDs (NBSs), are one of the most sensitive magnetometers for nanoscale magnetometry. Because of very strong nonlinearity in the nanobridge-electrode joints, the applied magnetic flux (${\mathrm{\ensuremath{\Phi}}}_{a}$)--critical current (Ic{I}_{c}Ic​) characteristics of NBSs differ very significantly from conventional tunnel-junction SQUIDs, especially when the nanobridges are long and/or the screening parameter is large. However, in most of the theoretical descriptions, NBSs have been treated as the conventional tunnel-junction SQUIDs, which are based on the dc Josephson effect. Here, I present a model demonstrating that for long nanobridges and/or large screening parameters the ${I}_{c}({\mathrm{\ensuremath{\Phi}}}_{a})$ of a NBS can be explained by merely considering the fluxoid quantization in the NBS loop and the energy of the NBS; it is not necessary to take the Josephson effect into consideration. I also demonstrate that using the model, one can derive useful expressions such as the modulation depth and transfer function. I discuss the role of the kinetic inductance fraction ($\ensuremath{\kappa}$) in determining ${I}_{c}({\mathrm{\ensuremath{\Phi}}}_{a})$. I compare the predictions of the present model with the experimental data already published by several groups.
Author(s): Antler, Natania | Advisor(s): Siddiqi, Irfan | Abstract: As the cutting edge of science and technology pushes towards smaller length scales, sensing technologies with nanoscale precision become increasingly important. In this thesis I will discuss the optimization and application of a 3D nanobridge SQUID magnetometer for studying solid state spin systems, in particular for sensing impurity spins in diamond. Solid state spins have proposed applications in memory and computation for both classical and quantum computing. Isolated spins typically have longer coherence times, making them attractive qubit candidates, but necessitating the development of very sensitive detectors for readout. This 3D nanobridge SQUID combines the exquisite spatial sensitivity of a traditional nanoSQUID with a large non-linearity on par with a tunnel junction SQUID. This allows us to build a highly sensitive magnetometer which can act as both an efficient flux transducer as well as a nearly quantum limited lumped Josephson Parametric Amplifier. We show that the device has a minimum flux noise of 17 ± 0.9 nΦ0/Hz1/2 with only a factor of ∼2.5 increase in flux noise up to 61 mT. A second generation device with a smaller capacitor achieves field tolerance up to 75 mT. The maximal bandwidth values range from 25-40 MHz in the parametric amplification regime to 70 MHz in the linear regime. This combination of large bandwidth, low flux noise, large flux coupling and field tolerance make this sensor a promising candidate for near-single-spin dynamics measurements.In the last part of this thesis we begin to demonstrate the utility of a nanobridge SQUID magnetometer for characterizing spin systems in the solid state. We use the magnetometer to measure the decay characteristics of P1 centers in diamond. We find that the spin-lattice relaxation time varies with temperature, with an order of magnitude decrease in the decay time between 25 mK and 370 mK.
Abstract We describe the theory and implementation of a dispersive magnetometer based on an aluminum nanoSQUID. The nanoSQUID consists of a superconducting loop interrupted by two variable-thickness weak-link nanobridge Josephson junctions. When the nanoSQUID is placed in parallel with a lumped-element capacitor, it acts as the inductive element in a resonant tank circuit. By performing microwave reflectometry on the circuit, the SQUID inductance can be measured, providing a sensitive meter of the flux threading the SQUID loop. In this review we provide the theoretical basis for the device, describe design and operation considerations, and present characterization results on several devices.
We describe a dispersive nanoSQUID (nanoscale superconducting quantum interference device) magnetometer comprised of two variable thickness aluminum weak-link Josephson junctions shunted in parallel with an on-chip capacitor. This arrangement forms a nonlinear oscillator with a tunable 4–8 GHz resonant frequency with a quality factor Q = 30 when coupled directly to a 50 Ω transmission line. In the presence of a near-resonant microwave carrier signal, a low frequency flux input generates sidebands that are readily detected using microwave reflectometry. If the carrier excitation is sufficiently strong, then the magnetometer also exhibits parametric gain, resulting in a minimum effective flux noise of 30 n Φ 0 Hz −1/2 with 20 MHz of instantaneous bandwidth. If the magnetometer is followed with a near-quantum-noise-limited Josephson parametric amplifier, we can increase the bandwidth to 60 MHz without compromising sensitivity. This combination of high sensitivity and wide bandwidth with no on-chip dissipation makes this device ideal for local sensing of spin dynamics, both classical and quantum.
In quantum technology, several aspects of superconductivity such as proximity effect have studied to develop a wide range of attractive applications at sub-kelvin temperatures. A new type of interferometer based on the proximity effect, taking place around transparent interfaces between normal- and superconducting metals, the Superconducting Quantum Interference Proximity Transistor (SQUIPT), relies on the phase dependence of the density of states in the proximized weak link. The SQUIPT devices offer the possibility to realize sensitive low-dissipation magnetometers compared to conventional DC SQUIDs. In this thesis, we investigate the development of the sensitive SQUIPT magnetometers. The first part of the thesis covers the characterization of non-hysteretic SQUIPTs with enhanced responsivity. In these structures, we demonstrate magnetic flux modulation of the device characteristics displaying no hysteresis at low temperatures by simply increasing the Josephson inductance of the weak link compared to self-inductance of the superconducting loop in the device. As a consequence, improvement in magnetic field responsivity is achievable. We then turn to the implementation of SQUIPT devices based on different fabrication methods and superconductor materials for improving the device performance. In this aspect, we fabricate and characterize niobium-based SNS devices utilizing two separate lithography and deposition steps with strong Ar ion cleaning in between. We further investigate a prototype hybrid SQUIPT device based on an Nb-Cu-Nb SNS junction with a conventional Al probe in tunnel junction. In the third part of the thesis, we present the flux noise characterization of a SQUIPT device using simultaneous measurement of DC transport properties and shot noise. To probe the noise, we use a cryogenic amplifier operating at frequencies in the range of a few MHz. We adapt this technique for flux noise measurements in SQUIPTs, adaptable also to low-temperature shot noise measurements of other nonlinear devices with high impedance. In order to investigate flux noise of SQUIPTs, we develop a model allowing one to optimize the figures of merit of the magnetometers such as the noise-equivalent flux.