Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

High- T c radio-frequency superconducting quantum interference devices fabricated from YBa 2 Cu 3 O 7-δ using focused helium ion beam technique

Ziwen 紫雯 Chen 陈, Yulong Li, Yan Zhang, Ping Ma, Yue Wang, Zizhao Gan

Published Oct 1, 2026• 0 citations
Publisher

Abstract

Abstract The reliable fabrication of high-sensitivity superconducting quantum interference devices (SQUIDs) with high critical transition temperature (high- T c ) is crucial for many practical applications such as weak magnetic sensing. In this work, we report the first realization of the YBa 2 Cu 3 O 7− δ (YBCO) radio frequency SQUIDs (rf SQUIDs) based on focused helium ion beam (FHIB) technique. A series of YBCO rf SQUIDs with high consistency were fabricated using a 30 keV FHIB with different helium ion (He + ) dose. The dose-dependent characteristics of the fabricated devices were systematically investigated at a temperature of 77 K. The experimental results verify that the variation in He + dose can effectively modulate the junction parameters and thereby the device noise performance. A non-monotonic white noise trend with increasing He + dose was observed, which could be primarily attributed to the transition of operational working regime of the fabricated rf SQUIDs. Based upon the dose optimization, a flux noise of 58 μ Φ 0 / H z 1 / 2 , corresponding to a field sensitivity of 185 f T / H z 1 / 2 , was achieved with our current device configuration. Approaches to further optimize the overall device performance are also discussed. Our work demonstrates FHIB-based high- T c SQUIDs with high junction parameter consistency a promising candidate for the implementation of multi-channel weak magnetic field detection systems and might hopefully serve as a platform for validating the theoretical models of high- T c SQUIDs.

DOI
10.1088/1361-6668/aeaece

Related papers

YBa$_{2}$Cu$_{3}$O$_{7-\delta }$Single Flux Quantum Flip Flop Directly Written With a Focused Helium Ion Beam

Han Cai, Hao Li, Ethan Y. Cho +2 more

Superconducting logic circuits based on low transition temperature (Tc) are attractive due to their intrinsic low power consumption and high operating frequency. They have a wide variety of applications (particularly in future computing), but are difficult to use because they require cooling with liquid helium to operate. The current high Tclogic circuit based on YBa2Cu3O7-δ(YBCO) already has the ability to operate at a temperature above 4 K. However, this material is difficult to integrate into large-scale circuits by the traditional YBCO junction fabrication process. The limits of fabrication methods are the bottleneck stifling this material's potential for integration into logic circuits. As such, in this paper we aim to advance the state of the art in junction fabrication technology. Here we report the demonstration of a high Tcsuperconducting single flux quantum (SFQ) circuit made by a focused helium ion beam that is easily fabricated and can readily be incorporated into a large-scale integration with nano-scale junctions for future applications. An inductively coupled readout superconducting quantum interference device (SQUID) is employed to reduce the circuit complexity. The circuit parameters and performance are discussed.

IEEE Transactions on Applied Superconductivity•Apr 1, 2021•15 citations

YBa2Cu3O7− δ superconducting quantum interference devices with metallic to insulating barriers written with a focused helium ion beam

Ethan Y. Cho, M. K., Chuong Huynh +5 more

In this work, we demonstrate the ability to fabricate superconducting quantum interference devices (SQUIDs) by directly writing Josephson junctions into the plane of YBa2Cu3O7−δ thin films with a focused helium ion beam. This technique allows for the control of the Josephson barrier transport properties through the single parameter, ion dose. SQUIDs written with a dose of 4 × 1016 ions/cm2 had metallic barrier junctions that exhibited nearly ideal electrical transport characteristics at 50 K and a flux noise of 20 μΦ0/Hz at 10 Hz. At higher irradiation doses, the SQUIDs had insulating barrier Josephson junctions with a quasi particle energy gap edge at 20 meV.

Applied Physics Letters•Jun 22, 2015•72 citations

Dynamic properties of high-Tc superconducting nano-junctions made with a focused helium ion beam

F. Couëdo, P. Amari, C. Feuillet-Palma +5 more

Abstract The Josephson junction (JJ) is the corner stone of superconducting electronics and quantum information processing. While the technology for fabricating low T c JJ is mature and delivers quantum circuits able to reach the “quantum supremacy”, the fabrication of reproducible and low-noise high- T c JJ is still a challenge to be taken up. Here we report on noise properties at RF frequencies of recently introduced high- T c Josephson nano-junctions fabricated by mean of a Helium ion beam focused at sub-nanometer scale on a YBa 2 Cu 3 O 7 thin film. We show that their current-voltage characteristics follow the standard Resistively-Shunted-Junction (RSJ) circuit model, and that their characteristic frequency f c = (2 e / h ) I c R n reaches ~300 GHz at low temperature. Using the “detector response” method, we evidence that the Josephson oscillation linewidth is only limited by the thermal noise in the RSJ model for temperature ranging from T ~ 20 K to 75 K. At lower temperature and for the highest He irradiation dose, the shot noise contribution must also be taken into account when approaching the tunneling regime. We conclude that these Josephson nano-junctions present the lowest noise level possible, which makes them very promising for future applications in the microwave and terahertz regimes.

arXiv:1908.11163•Scientific Reports•Jun 24, 2020•26 citations

YBa$_2$Cu$_3$O$_7$ nano-constriction Josephson junctions and SQUIDs fabricated by focused helium-ion-beam irradiation

Christoph Schmid, Christopher Buckreus, David Haas +9 more

By focused $30\,\mathrm{keV}$ He ion beam irradiation, epitaxially grown YBa$_2$Cu$_3$O$_7$ (YBCO) thin films can be driven from the superconducting to the insulating state with increasing irradiation dose. A properly chosen dose suppresses superconductivity down to $4\,\mathrm{K}$, while crystallinity is still preserved. With this approach we create areas of normal-conducting YBCO that can be used to define resistively shunted constriction-type Josephson junctions (cJJs) on the nanometer scale. We also demonstrate that the fabricated cJJs can be incorporated in direct current superconducting quantum interference devices and can be used as detector junctions in THz antennas.

cond-mat.supr-conCross-listedarXiv:2511.19197•Nov 25, 2025•4 citations

A flux-tunable YBa2Cu3O7 quantum interference microwave circuit

Kevin Uhl, Daniel Hackenbeck, Christoph Füger +3 more

Josephson microwave circuits are essential for the currently flourishing research on superconducting technologies, such as quantum computation, quantum sensing, and microwave signal processing. To increase the possible parameter space for device operation with respect to the current standards, many materials for superconducting circuits are under active investigation. Here, we present the realization of a frequency-tunable, weakly nonlinear Josephson microwave circuit made of the high-temperature cuprate superconductor YBa2Cu3O7 (YBCO), a material with a high critical temperature and a very high critical magnetic field. An in situ frequency-tunability of ∼300 MHz is achieved by integrating a superconducting quantum interference device (SQUID) into the circuit based on Josephson junctions directly written with a helium ion microscope (HIM). Our results demonstrate that YBCO-HIM-SQUID microwave resonators are promising candidates for quantum sensing and microwave technology applications.

Applied Physics Letters•May 1, 2023•6 citations

YBa 2 Cu 3 O 7 nano superconducting quantum interference devices on MgO bicrystal substrates

Jianxin Lin, Benedikt Müller, Julian Linek +5 more

We report on nanopatterned YBa2Cu3O7-δ (YBCO) direct current superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions. The nanoSQUIDs are fabricated by epitaxial growth of 120 nm-thick films of the high-transition temperature cuprate superconductor YBCO via pulsed laser deposition on MgO bicrystal substrates with 24° misorientation angle, followed by sputtering of dAu = 65 nm thick Au. Nanopatterning is performed by Ga focused ion beam (FIB) milling. The SQUID performance is comparable to devices on SrTiO3 (STO), as demonstrated by electric transport and noise measurements at 4.2 K. MgO has orders of magnitude smaller dielectric permittivity than STO; i.e., one may avoid Au as a resistively shunting layer to reduce the intrinsic thermal flux noise of the nanoSQUIDs. However, we find that the Au layer is important for avoiding degradation during FIB milling. Hence, we compare devices with different dAu produced by thinning the Au layer via Ar ion milling after FIB patterning. We find that the reduction of dAu yields an increase in junction resistance, however at the expense of a reduction of the critical current and increase in SQUID inductance. This results in an estimated thermal flux noise that is almost independent of dAu. However, for two devices on MgO with 65 nm-thick Au, we find an order of magnitude lower low-frequency excess noise as compared to nanoSQUIDs on STO or those on MgO with reduced dAu. For one of those devices we obtain with bias-reversal readout ultra-low flux noise of ∼175 nΦ0 Hz-1/2 down to ∼10 Hz.

Nanoscale•Jan 1, 2020•17 citations
Abstract The reliable fabrication of high-sensitivity superconducting quantum interference devices (SQUIDs) with high critical transition temperature (high- T c ) is crucial for many practical applications such as weak magnetic sensing. In this work, we report the first realization of the YBa 2 Cu 3 O 7− δ (YBCO) radio frequency SQUIDs (rf SQUIDs) based on focused helium ion beam (FHIB) technique. A series of YBCO rf SQUIDs with high consistency were fabricated using a 30 keV FHIB with different helium ion (He + ) dose. The dose-dependent characteristics of the fabricated devices were systematically investigated at a temperature of 77 K. The experimental results verify that the variation in He + dose can effectively modulate the junction parameters and thereby the device noise performance. A non-monotonic white noise trend with increasing He + dose was observed, which could be primarily attributed to the transition of operational working regime of the fabricated rf SQUIDs. Based upon the dose optimization, a flux noise of 58 μ Φ 0 / H z 1 / 2 , corresponding to a field sensitivity of 185 f T / H z 1 / 2 , was achieved with our current device configuration. Approaches to further optimize the overall device performance are also discussed. Our work demonstrates FHIB-based high- T c SQUIDs with high junction parameter consistency a promising candidate for the implementation of multi-channel weak magnetic field detection systems and might hopefully serve as a platform for validating the theoretical models of high- T c SQUIDs.
YBa2_{2}2​Cu3_{3}3​O7−δ_{7-\delta }7−δ​Single Flux Quantum Flip Flop Directly Written With a Focused Helium Ion Beam
Superconducting logic circuits based on low transition temperature (Tc) are attractive due to their intrinsic low power consumption and high operating frequency. They have a wide variety of applications (particularly in future computing), but are difficult to use because they require cooling with liquid helium to operate. The current high Tclogic circuit based on YBa2Cu3O7-δ(YBCO) already has the ability to operate at a temperature above 4 K. However, this material is difficult to integrate into large-scale circuits by the traditional YBCO junction fabrication process. The limits of fabrication methods are the bottleneck stifling this material's potential for integration into logic circuits. As such, in this paper we aim to advance the state of the art in junction fabrication technology. Here we report the demonstration of a high Tcsuperconducting single flux quantum (SFQ) circuit made by a focused helium ion beam that is easily fabricated and can readily be incorporated into a large-scale integration with nano-scale junctions for future applications. An inductively coupled readout superconducting quantum interference device (SQUID) is employed to reduce the circuit complexity. The circuit parameters and performance are discussed.
In this work, we demonstrate the ability to fabricate superconducting quantum interference devices (SQUIDs) by directly writing Josephson junctions into the plane of YBa2Cu3O7−δ thin films with a focused helium ion beam. This technique allows for the control of the Josephson barrier transport properties through the single parameter, ion dose. SQUIDs written with a dose of 4 × 1016 ions/cm2 had metallic barrier junctions that exhibited nearly ideal electrical transport characteristics at 50 K and a flux noise of 20 μΦ0/Hz at 10 Hz. At higher irradiation doses, the SQUIDs had insulating barrier Josephson junctions with a quasi particle energy gap edge at 20 meV.
Abstract The Josephson junction (JJ) is the corner stone of superconducting electronics and quantum information processing. While the technology for fabricating low T c JJ is mature and delivers quantum circuits able to reach the “quantum supremacy”, the fabrication of reproducible and low-noise high- T c JJ is still a challenge to be taken up. Here we report on noise properties at RF frequencies of recently introduced high- T c Josephson nano-junctions fabricated by mean of a Helium ion beam focused at sub-nanometer scale on a YBa 2 Cu 3 O 7 thin film. We show that their current-voltage characteristics follow the standard Resistively-Shunted-Junction (RSJ) circuit model, and that their characteristic frequency f c = (2 e / h ) I c R n reaches ~300 GHz at low temperature. Using the “detector response” method, we evidence that the Josephson oscillation linewidth is only limited by the thermal noise in the RSJ model for temperature ranging from T ~ 20 K to 75 K. At lower temperature and for the highest He irradiation dose, the shot noise contribution must also be taken into account when approaching the tunneling regime. We conclude that these Josephson nano-junctions present the lowest noise level possible, which makes them very promising for future applications in the microwave and terahertz regimes.
YBa2_22​Cu3_33​O7_77​ nano-constriction Josephson junctions and SQUIDs fabricated by focused helium-ion-beam irradiation
By focused 30 keV30\,\mathrm{keV}30keV He ion beam irradiation, epitaxially grown YBa2_22​Cu3_33​O7_77​ (YBCO) thin films can be driven from the superconducting to the insulating state with increasing irradiation dose. A properly chosen dose suppresses superconductivity down to 4 K4\,\mathrm{K}4K, while crystallinity is still preserved. With this approach we create areas of normal-conducting YBCO that can be used to define resistively shunted constriction-type Josephson junctions (cJJs) on the nanometer scale. We also demonstrate that the fabricated cJJs can be incorporated in direct current superconducting quantum interference devices and can be used as detector junctions in THz antennas.
Josephson microwave circuits are essential for the currently flourishing research on superconducting technologies, such as quantum computation, quantum sensing, and microwave signal processing. To increase the possible parameter space for device operation with respect to the current standards, many materials for superconducting circuits are under active investigation. Here, we present the realization of a frequency-tunable, weakly nonlinear Josephson microwave circuit made of the high-temperature cuprate superconductor YBa2Cu3O7 (YBCO), a material with a high critical temperature and a very high critical magnetic field. An in situ frequency-tunability of ∼300 MHz is achieved by integrating a superconducting quantum interference device (SQUID) into the circuit based on Josephson junctions directly written with a helium ion microscope (HIM). Our results demonstrate that YBCO-HIM-SQUID microwave resonators are promising candidates for quantum sensing and microwave technology applications.
We report on nanopatterned YBa2Cu3O7-δ (YBCO) direct current superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions. The nanoSQUIDs are fabricated by epitaxial growth of 120 nm-thick films of the high-transition temperature cuprate superconductor YBCO via pulsed laser deposition on MgO bicrystal substrates with 24° misorientation angle, followed by sputtering of dAu = 65 nm thick Au. Nanopatterning is performed by Ga focused ion beam (FIB) milling. The SQUID performance is comparable to devices on SrTiO3 (STO), as demonstrated by electric transport and noise measurements at 4.2 K. MgO has orders of magnitude smaller dielectric permittivity than STO; i.e., one may avoid Au as a resistively shunting layer to reduce the intrinsic thermal flux noise of the nanoSQUIDs. However, we find that the Au layer is important for avoiding degradation during FIB milling. Hence, we compare devices with different dAu produced by thinning the Au layer via Ar ion milling after FIB patterning. We find that the reduction of dAu yields an increase in junction resistance, however at the expense of a reduction of the critical current and increase in SQUID inductance. This results in an estimated thermal flux noise that is almost independent of dAu. However, for two devices on MgO with 65 nm-thick Au, we find an order of magnitude lower low-frequency excess noise as compared to nanoSQUIDs on STO or those on MgO with reduced dAu. For one of those devices we obtain with bias-reversal readout ultra-low flux noise of ∼175 nΦ0 Hz-1/2 down to ∼10 Hz.