Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Nanoscale

YBa 2 Cu 3 O 7 nano superconducting quantum interference devices on MgO bicrystal substrates

Jianxin Lin, Benedikt Müller, Julian Linek, Max Karrer, Malte Wenzel, M.J. Pérez, R. Kleiner, D. Koelle

Published Jan 1, 2020• 17 citations
Publisher

Abstract

We report on nanopatterned YBa2Cu3O7-δ (YBCO) direct current superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions. The nanoSQUIDs are fabricated by epitaxial growth of 120 nm-thick films of the high-transition temperature cuprate superconductor YBCO via pulsed laser deposition on MgO bicrystal substrates with 24° misorientation angle, followed by sputtering of dAu = 65 nm thick Au. Nanopatterning is performed by Ga focused ion beam (FIB) milling. The SQUID performance is comparable to devices on SrTiO3 (STO), as demonstrated by electric transport and noise measurements at 4.2 K. MgO has orders of magnitude smaller dielectric permittivity than STO; i.e., one may avoid Au as a resistively shunting layer to reduce the intrinsic thermal flux noise of the nanoSQUIDs. However, we find that the Au layer is important for avoiding degradation during FIB milling. Hence, we compare devices with different dAu produced by thinning the Au layer via Ar ion milling after FIB patterning. We find that the reduction of dAu yields an increase in junction resistance, however at the expense of a reduction of the critical current and increase in SQUID inductance. This results in an estimated thermal flux noise that is almost independent of dAu. However, for two devices on MgO with 65 nm-thick Au, we find an order of magnitude lower low-frequency excess noise as compared to nanoSQUIDs on STO or those on MgO with reduced dAu. For one of those devices we obtain with bias-reversal readout ultra-low flux noise of ∼175 nΦ0 Hz-1/2 down to ∼10 Hz.

DOI
10.1039/c9nr10506a

Related papers

Long-time stable and high-performance YBa2Cu3O7 nanoSQUIDs with more interfaces

Jianxin Lin, Deheng Zhang, Lianjun Zhao +3 more

We report on the fabrication and characterization of nanopatterned superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions in epitaxially grown multilayer YBa2Cu3O7 (YBCO)/SiTrO3 (STO) thin films. Nanopatterning is performed by Ga+ focused ion beam milling. The evolution of the electric transport and noise properties of the YBCO nanoSQUIDs over a time span of more than one year are recorded and analyzed. We find that the multilayer YBCO/STO nanoSQUIDs show stable and high performance over time. The critical current decreases within ∼40 days by 30%–50% and then remains almost constant without obvious decline trend for nanoSQUIDs with STO layer as the interface even more than 380 days, which demonstrates the superiority of STO as the capping layer. Moreover, we find that the multilayer nanoSQUIDs have about an order of magnitude smaller low-frequency excess flux noise (compared to similar single layer devices) with root-mean-square spectral density ∼5–6 µΦ0/Hz1/2 at 1 Hz. For one device, we show that the low-frequency excess noise does not degrade within three months.

AIP Advances•Apr 1, 2022•1 citation

DC superconducting quantum interference devices fabricated using bicrystal grain boundary junctions in Co-doped BaFe2As2epitaxial films

Takayoshi Katase, Yoshihiro Ishimaru, Akira Tsukamoto +4 more

DC superconducting quantum interference devices (dc-SQUIDs) were fabricated in Co-doped BaFe 2 As 2 epitaxial films on (La, Sr)(Al, Ta)O 3 bicrystal substrates with 30° misorientation angles. The 18 × 8 µm 2 SQUID loop with an estimated inductance of 13 pH contained two 3 µm wide grain boundary junctions. The voltage–flux characteristics clearly exhibited periodic modulations with Δ V = 1.4 µV at 14 K, while the intrinsic flux noise of dc-SQUIDs was 7.8 × 10 − 5 Φ 0 Hz − 1/2 above 20 Hz. The rather high flux noise is mainly attributed to the small voltage modulation depth which results from the superconductor–normal-metal–superconductor junction nature of the bicrystal grain boundary.

arXiv:1005.2021•Superconductor Science and Technology•Jul 2, 2010•50 citations

Low frequency (1/f) noise in YBa2Cu3O7−δ grain boundary junction dc superconducting quantum interference devices

J. Chen, T. Ogawa, Hiroyuki Nakamura +3 more

We have studied low frequency (1/f) noise of YBa2Cu3O7−δ dc superconducting quantum interference devices (SQUIDs) on SrTiO3 bicrystal substrates. 1/f flux noise, either measured at different temperatures for optimized bias current or measured at 77 K for different bias currents, is almost constant. These facts imply that 1/f noise mainly comes from fluctuations of the critical current of the Josephson junction that form the SQUID. Also, we explain the critical current fluctuations in the junction by an equilibrium temperature fluctuation model.

Journal of Applied Physics•Aug 1, 1994•13 citations

Fabrication of micro-superconducting quantum interference devices based on nano laser direct writing

Wenqian Liu, Shuo Xiang, Yicong Huang +11 more

Abstract We propose the fabrication of micro-superconducting quantum interference devices via nano laser direct writing (NLDW). A 20 nm thick Nb film with a critical transition temperature of 9.2 K was deposited on a silicon substrate by sputtering, and nanopatterning was performed with NLDW. After optimizing parameters such as the laser pulse width and power, we investigated the electrical performance of SQUIDs by varying the laser power between 245 mW and 270 mW in 5 mW steps. Experimentally, the voltage–flux (V–Φ) characteristics of micro SQUIDs exhibited typical periodic modulation, confirming the Josephson effect and magnetic flux quantization effect based on the NLDW process. The noise spectral density measurements of SQUID fabricated with laser power of 265 mW achieved a white noise level of 3 μ Φ 0 /Hz 1 / 2 , demonstrating comparable flux noise sensitivity compared to electron beam and ion beam fabrication processes. Furthermore, the devices retained stable superconducting and electrical performance after 101 days, illustrating excellent long-term stability. To some extent, the NLDW shows the potential to perform micro-nanopatterning of superconducting devices efficiently and cost-effectively, as well as an avenue for conducting nanoscale thermal engineering on superconducting devices for basic science research.

Journal of Physics D Applied Physics•Aug 13, 2025•2 citations

Noise properties of nanoscale YBa 2 Cu 3 O 7−δ Josephson junctions

David Gustafsson, Floriana Lombardi, Thilo Bauch

We present electric noise measurements of nanoscale biepitaxial YBa${}_{2}$Cu${}_{3}$O${}_{7\ensuremath{-}\ensuremath{\delta}}$ (YBCO) Josephson junctions fabricated by two different lithographic methods. The first (conventional) technique defines the junctions directly by ion milling etching through an amorphous carbon mask. The second (soft patterning) method makes use of the phase competition between the superconducting YBCO (Y123) and the insulating Y${}_{2}$BaCuO${}_{5}$ (Y211) phase at the grain boundary interface on MgO (110) substrates. The voltage noise properties of the two methods are compared in this study. For all junctions (having a thickness of 100 nm and widths of 250--500 nm), we see a significant amount of individual charge traps. We have extracted an approximate value for the effective area of the charge traps from the noise data. From the noise measurements, we infer that the soft-patterned junctions with a grain-boundary (GB) interface manifesting a large $c$-axis tunneling component have a uniform barrier and a superconductor-insulator-superconductor (SIS) -like behavior. The noise properties of soft-patterned junctions having a GB interface dominated by transport parallel to the $ab$ planes are in accordance with a resonant tunneling barrier model. The conventionally patterned junctions, instead, have suppressed superconducting transport channels with an area much less than the nominal junction area. These findings are important for the implementation of nanosized Josephson junctions in quantum circuits.

arXiv:1112.0680•Physical Review B•Nov 28, 2011•14 citations

Low 1/f noise single-layer YBa2Cu3Ox dc SQUID at 77 K

Gergely Friedl, M. Vildić, Bernhard Roas +6 more

Autonomous single-layer dc superconducting quantum interference devices (SQUIDs) have been prepared from epitaxial, laser-deposited YBa2Cu3Ox films on step edge SrTiO3 and LaAlO3 substrates. For device patterning, a SiOx inhibit technique as well as conventional ethylenediaminetetraacetic wet etch was used. The Josephson junctions are of grain boundary type. Their widths are 5 μm. The SQUID hole is a square of about 5 μm; the SQUID inductance is estimated to be about 20 pH. We obtained a very regular, nonhysteretic flux to voltage modulation over more than 100 flux quanta (Φ0). The maximum voltage signal is of the order of 15 μV peak to peak and the maximum transfer function dV/dΦ at the appropriate flux bias is 50 μV/Φ0 at 77 K. The best value of the equivalent flux noise as measured in the flux locked loop mode is 1.4×10−5 Φ0/Hz1/2 at 1 Hz and 1×10−5 Φ0/Hz1/2 in the white noise region for f≳5 Hz. This results in an energy resolution εn,w(f≳5 Hz)=1×10−29 J/Hz in the white noise region and 2×10−29 J/Hz at 1 Hz.

Applied Physics Letters•Jun 15, 1992•69 citations
We report on nanopatterned YBa2Cu3O7-δ (YBCO) direct current superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions. The nanoSQUIDs are fabricated by epitaxial growth of 120 nm-thick films of the high-transition temperature cuprate superconductor YBCO via pulsed laser deposition on MgO bicrystal substrates with 24° misorientation angle, followed by sputtering of dAu = 65 nm thick Au. Nanopatterning is performed by Ga focused ion beam (FIB) milling. The SQUID performance is comparable to devices on SrTiO3 (STO), as demonstrated by electric transport and noise measurements at 4.2 K. MgO has orders of magnitude smaller dielectric permittivity than STO; i.e., one may avoid Au as a resistively shunting layer to reduce the intrinsic thermal flux noise of the nanoSQUIDs. However, we find that the Au layer is important for avoiding degradation during FIB milling. Hence, we compare devices with different dAu produced by thinning the Au layer via Ar ion milling after FIB patterning. We find that the reduction of dAu yields an increase in junction resistance, however at the expense of a reduction of the critical current and increase in SQUID inductance. This results in an estimated thermal flux noise that is almost independent of dAu. However, for two devices on MgO with 65 nm-thick Au, we find an order of magnitude lower low-frequency excess noise as compared to nanoSQUIDs on STO or those on MgO with reduced dAu. For one of those devices we obtain with bias-reversal readout ultra-low flux noise of ∼175 nΦ0 Hz-1/2 down to ∼10 Hz.
We report on the fabrication and characterization of nanopatterned superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions in epitaxially grown multilayer YBa2Cu3O7 (YBCO)/SiTrO3 (STO) thin films. Nanopatterning is performed by Ga+ focused ion beam milling. The evolution of the electric transport and noise properties of the YBCO nanoSQUIDs over a time span of more than one year are recorded and analyzed. We find that the multilayer YBCO/STO nanoSQUIDs show stable and high performance over time. The critical current decreases within ∼40 days by 30%–50% and then remains almost constant without obvious decline trend for nanoSQUIDs with STO layer as the interface even more than 380 days, which demonstrates the superiority of STO as the capping layer. Moreover, we find that the multilayer nanoSQUIDs have about an order of magnitude smaller low-frequency excess flux noise (compared to similar single layer devices) with root-mean-square spectral density ∼5–6 µΦ0/Hz1/2 at 1 Hz. For one device, we show that the low-frequency excess noise does not degrade within three months.
DC superconducting quantum interference devices (dc-SQUIDs) were fabricated in Co-doped BaFe 2 As 2 epitaxial films on (La, Sr)(Al, Ta)O 3 bicrystal substrates with 30° misorientation angles. The 18 × 8 µm 2 SQUID loop with an estimated inductance of 13 pH contained two 3 µm wide grain boundary junctions. The voltage–flux characteristics clearly exhibited periodic modulations with Δ V = 1.4 µV at 14 K, while the intrinsic flux noise of dc-SQUIDs was 7.8 × 10 − 5 Φ 0 Hz − 1/2 above 20 Hz. The rather high flux noise is mainly attributed to the small voltage modulation depth which results from the superconductor–normal-metal–superconductor junction nature of the bicrystal grain boundary.
We have studied low frequency (1/f) noise of YBa2Cu3O7−δ dc superconducting quantum interference devices (SQUIDs) on SrTiO3 bicrystal substrates. 1/f flux noise, either measured at different temperatures for optimized bias current or measured at 77 K for different bias currents, is almost constant. These facts imply that 1/f noise mainly comes from fluctuations of the critical current of the Josephson junction that form the SQUID. Also, we explain the critical current fluctuations in the junction by an equilibrium temperature fluctuation model.
Abstract We propose the fabrication of micro-superconducting quantum interference devices via nano laser direct writing (NLDW). A 20 nm thick Nb film with a critical transition temperature of 9.2 K was deposited on a silicon substrate by sputtering, and nanopatterning was performed with NLDW. After optimizing parameters such as the laser pulse width and power, we investigated the electrical performance of SQUIDs by varying the laser power between 245 mW and 270 mW in 5 mW steps. Experimentally, the voltage–flux (V–Φ) characteristics of micro SQUIDs exhibited typical periodic modulation, confirming the Josephson effect and magnetic flux quantization effect based on the NLDW process. The noise spectral density measurements of SQUID fabricated with laser power of 265 mW achieved a white noise level of 3 μ Φ 0 /Hz 1 / 2 , demonstrating comparable flux noise sensitivity compared to electron beam and ion beam fabrication processes. Furthermore, the devices retained stable superconducting and electrical performance after 101 days, illustrating excellent long-term stability. To some extent, the NLDW shows the potential to perform micro-nanopatterning of superconducting devices efficiently and cost-effectively, as well as an avenue for conducting nanoscale thermal engineering on superconducting devices for basic science research.
We present electric noise measurements of nanoscale biepitaxial YBa2{}_{2}2​Cu3{}_{3}3​O${}_{7\ensuremath{-}\ensuremath{\delta}}$ (YBCO) Josephson junctions fabricated by two different lithographic methods. The first (conventional) technique defines the junctions directly by ion milling etching through an amorphous carbon mask. The second (soft patterning) method makes use of the phase competition between the superconducting YBCO (Y123) and the insulating Y2{}_{2}2​BaCuO5{}_{5}5​ (Y211) phase at the grain boundary interface on MgO (110) substrates. The voltage noise properties of the two methods are compared in this study. For all junctions (having a thickness of 100 nm and widths of 250--500 nm), we see a significant amount of individual charge traps. We have extracted an approximate value for the effective area of the charge traps from the noise data. From the noise measurements, we infer that the soft-patterned junctions with a grain-boundary (GB) interface manifesting a large ccc-axis tunneling component have a uniform barrier and a superconductor-insulator-superconductor (SIS) -like behavior. The noise properties of soft-patterned junctions having a GB interface dominated by transport parallel to the ababab planes are in accordance with a resonant tunneling barrier model. The conventionally patterned junctions, instead, have suppressed superconducting transport channels with an area much less than the nominal junction area. These findings are important for the implementation of nanosized Josephson junctions in quantum circuits.
Autonomous single-layer dc superconducting quantum interference devices (SQUIDs) have been prepared from epitaxial, laser-deposited YBa2Cu3Ox films on step edge SrTiO3 and LaAlO3 substrates. For device patterning, a SiOx inhibit technique as well as conventional ethylenediaminetetraacetic wet etch was used. The Josephson junctions are of grain boundary type. Their widths are 5 μm. The SQUID hole is a square of about 5 μm; the SQUID inductance is estimated to be about 20 pH. We obtained a very regular, nonhysteretic flux to voltage modulation over more than 100 flux quanta (Φ0). The maximum voltage signal is of the order of 15 μV peak to peak and the maximum transfer function dV/dΦ at the appropriate flux bias is 50 μV/Φ0 at 77 K. The best value of the equivalent flux noise as measured in the flux locked loop mode is 1.4×10−5 Φ0/Hz1/2 at 1 Hz and 1×10−5 Φ0/Hz1/2 in the white noise region for f≳5 Hz. This results in an energy resolution εn,w(f≳5 Hz)=1×10−29 J/Hz in the white noise region and 2×10−29 J/Hz at 1 Hz.