Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Symposium on Microelectronics Technology and Devices

Design, Simulation, and Experimental Validation of 3D Resonant Cavities for CryoCMOS and Superconducting Qubit Readout

Beatriz Sacramento, Ednilson Lopes, Francisco P. M. Rouxinol

Published Aug 1, 2026• 0 citations
Publisher

Abstract

Three-dimensional microwave cavities are key components for superconducting-qubit readout and for the characterization of cryogenic microwave electronics [1]. In this work, we report the design, simulation, fabrication, and experimental validation of a rectangular 3D resonant cavity targeting operation near 5.4 GHz, compatible with the frequency range of CryoCMOS voltage-controlled oscillators (VCO). The cavity dimensions were obtained from analytical mode calculations, corrected for practical machining constraints, and validated using finite-element electromagnetic simulations in ANSYS HFSS. A split-block aluminum cavity was fabricated and characterized at room temperature using vector network analysis. The measured resonances agree with analytical and simulated predictions within sub-1% deviation, confirming the accuracy of the design procedure. Different SMA connector penetration configurations were experimentally investigated to evaluate the trade-off between loaded quality factor and transmission efficiency. The asymmetric $7 \mathrm{~mm} / 8 \mathrm{~mm}$ configuration provided the best compromise, yielding a loaded quality factor of approximately 3200 and improving the transmitted signal by about 20 dB compared with the symmetric $\mathrm{7 ~ m m} / \mathrm{7 ~ m m}$ configuration. These results demonstrate a reproducible design route for 3D cavities intended for CryoCMOS testing and future superconducting-qubit readout experiments.

DOI
10.1109/sbmicro70495.2026.11684416

Related papers

Development of high quality superconducting resonators for quantum device applications

Dong-Gwang Ha, Seon Hoo Kim, So-Yeon Jun +5 more

We report our development on design, fabrication and characterization of various superconducting resonators for quantum device applications. The resonators are developed mainly for superconducting qubit implementation in circuit QED structure, but future application will include photon detectors such as microwave kinetic inductance detectors. First we designed and fabricated half-wavelength coplanar waveguide resonators with niobium thin film on a high resistive silicon wafer, with the fundamental frequencies in the range of 1 to 8 GHz. The loaded quality factors are controlled by the coupling capacitors, and the lower bound of the intrinsic quality factor was measured down to 7 mK in the dilution refrigerator. We have also designed quarter-wavelength resonators and lumped LC resonators coupled to a transmission line, and characterized multiple resonators in a single transmission line. For the 3D transmon qubit application, we designed and fabricated a rectangular box resonator with superconducting aluminum. The intrinsic quality factor of the box resonator exceeds three million at 7 mK. We will also present basic results on the integration of a transmon qubit in the superconducting resonator.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2013•0 citations

Experimentally Verified, Fast Analytic, and Numerical Design of Superconducting Resonators in Flip-Chip Architectures

Hang-Xi Li, Daryoush Shiri, Sandoko Kosen +10 more

In superconducting quantum processors, the predictability of device parameters is of increasing importance as many labs scale up their systems to larger sizes in a 3D-integrated architecture. In particular, the properties of superconducting resonators must be controlled well to ensure high-fidelity multiplexed readout of qubits. Here we present a method, based on conformal mapping techniques, to predict a resonator's parameters directly from its 2D cross-section, without computationally heavy and time-consuming 3D simulation. We demonstrate the method's validity by comparing the calculated resonator frequency and coupling quality factor with those obtained through 3D finite-element-method simulation and by measurement of 15 resonators in a flip-chip-integrated architecture. We achieve a discrepancy of less than 2% between designed and measured frequencies, for 6-GHz resonators. We also propose a design method that reduces the sensitivity of the resonant frequency to variations in the inter-chip spacing.

arXiv:2305.05502•IEEE Transactions on Quantum Engineering•Jan 1, 2023•14 citations

Cryogenic microwave filter cavity with a tunability greater than 5 GHz

Thomas J. Clark, Vaisakh Vadakkumbatt, Fabien Souris +2 more

A wide variety of applications of microwave cavities, such as measurement and control of superconducting qubits, magnonic resonators, and phase noise filters, would be well served by having a highly tunable microwave resonance. Often this tunability is desired in situ at low temperatures, where one can take advantage of superconducting cavities. To date, such cryogenic tuning while maintaining a high quality factor has been limited to ∼500 MHz. Here we demonstrate a three-dimensional superconducting microwave cavity that shares one wall with a pressurized volume of helium. Upon pressurization of the helium chamber, the microwave cavity is deformed, which results in in situ tuning of its resonant frequency by more than 5 GHz, greater than 60% of the original 8 GHz resonant frequency. The quality factor of the cavity remains approximately constant at ≈7 × 103 over the entire range of tuning. As a demonstration of its usefulness, we implement a tunable cryogenic phase noise filter, which reduces the phase noise of our source by approximately 10 dB above 400 kHz.

arXiv:1810.02404•Review of Scientific Instruments•Nov 1, 2018•15 citations

Design and Modeling of Double-Fold Superconducting High-Q Coplanar Waveguide Resonators for Quantum Applications

Jagmohan Singh, Hongxiang Shen, Nobuyuki Yoshikawa +2 more

In this paper, we present a novel design of a compact, double-fold half-wave superconducting coplanar waveguide resonator, specifically optimized for quantum readout. The geometry offers advantages in terms of scalability and allows for a more compact integration of qubits per unit area. The superconducting resonators are designed to operate within a fundamental frequency range of 1.9 GHz$-$1.95 GHz, utilizing both gap and finger coupling schemes. The devices are fabricated using thin aluminum films deposited on high-resistivity sapphire substrates. The proposed resonators exhibit quality factor (Q$_{L}$) of 2.9 ×$ 10^{5}$and 1.58 ×$10^{3}$for gap coupled and finger coupled, respectively, during experimental measurements. The simulated Q$_{L}$of single-folded meander line resonators are found to be 4.65 ×$10^{5}$and 258.42, for gap coupled and finger coupled, respectively, for comparison purpose at similar operating frequency. A comprehensive analysis of the microwave transmission spectra was conducted at cryogenic temperatures near 10 mK, across very high input drive powers ($-$30 dBm to$-$10 dBm). Experimental results show a good agreement with simulations and the equivalent lumped circuit model. Notably, the proposed design reduces the physical footprint of the resonator devices up to 28.2$\%$compared to conventional single-fold meandered structures. The resonators demonstrate strong potential for integrating qubits with readout and control buses in quantum information processing which require a Q$_{L}$between$10^{4}$$-$$10^{5}$. They also being well-suited for cryogenic detector applications that utilize microwave kinetic inductance detector (MKID) arrays in frequency multiplexing for different coupling schemes.

IEEE Transactions on Applied Superconductivity•Sep 1, 2025•3 citations

First cryogenic test results of 3D-printed resonators for quantum bits

Paul R. Carriere, P. Frigola, Ronald Agustsson +7 more

Abstract Quantum computers (QC) have the potential to efficiently solve problems currently unfeasible on even the fastest generation of classical computers. The building block of a QC is a quantum bit (qubit). Encoding and reading qubit states coupled via high-Q resonant cavity modes is a solution to maintaining qubit states; however there is a need for simple, scalable and robust fabrication techniques capable of realizing high density cavity arrays. RadiaBeam is developing a novel approach utilizing metal additive manufacturing(AM) using both laser and electron beam powder bed fusion. Using a 6GHz quarter wave resonator (QWR), we fabricated several niobium and titanium alloy QWR cavities and characterized their superconducting RF performance. In this letter, we provide the details of the first 3D-printed qubit cavities design and fabrication, and compare their Q-factors, measured at dilution fridge temperatures, against the machined Nb resonators.

IOP Conference Series Materials Science and Engineering•May 1, 2022•3 citations

A Versatile Analytical Model for Fast and Accurate Determination of Feedline-Coupled Resonators for Superconducting Qubit Readout

Zhen Luo, Lea Richard, Ivan Tsitsilin +4 more

Superconducting quantum chips commonly utilize quarter-wavelength (λ/4) transmission line resonators as readout circuits. An analytical model for the accurate determination of resonance frequencies and coupling Q-factors of feedline-coupled superconducting resonators is introduced. The model leverages four-port microwave network analysis, integrating boundary conditions and conformal mapping techniques to compute even- and odd-mode impedances in edge-coupled coplanar waveguide (CPW) structures. Its versatility allows application to both planar and 3-D heterogeneous architectures, making it a powerful tool for resonator design. To validate the model, a test chip with λ/4 resonators of varying geometries is fabricated and measured in a cryogenic environment. Comparisons with finite element method (FEM) simulations and experimental measurements confirm the model's accuracy, with resonance frequencies and coupling Q-factors aligning closely across configurations. This proposed model facilitates the design of superconducting resonators in readout circuits for more effective, scalable, and adaptable quantum computing architectures.

quant-pharXiv:2607.00490•IEEE Transactions on Microwave Theory and Techniques•Jul 2, 2026•2 citations
Three-dimensional microwave cavities are key components for superconducting-qubit readout and for the characterization of cryogenic microwave electronics [1]. In this work, we report the design, simulation, fabrication, and experimental validation of a rectangular 3D resonant cavity targeting operation near 5.4 GHz, compatible with the frequency range of CryoCMOS voltage-controlled oscillators (VCO). The cavity dimensions were obtained from analytical mode calculations, corrected for practical machining constraints, and validated using finite-element electromagnetic simulations in ANSYS HFSS. A split-block aluminum cavity was fabricated and characterized at room temperature using vector network analysis. The measured resonances agree with analytical and simulated predictions within sub-1% deviation, confirming the accuracy of the design procedure. Different SMA connector penetration configurations were experimentally investigated to evaluate the trade-off between loaded quality factor and transmission efficiency. The asymmetric 7 mm/8 mm7 \mathrm{~mm} / 8 \mathrm{~mm}7 mm/8 mm configuration provided the best compromise, yielding a loaded quality factor of approximately 3200 and improving the transmitted signal by about 20 dB compared with the symmetric 7 mm/7 mm\mathrm{7 ~ m m} / \mathrm{7 ~ m m}7 mm/7 mm configuration. These results demonstrate a reproducible design route for 3D cavities intended for CryoCMOS testing and future superconducting-qubit readout experiments.
We report our development on design, fabrication and characterization of various superconducting resonators for quantum device applications. The resonators are developed mainly for superconducting qubit implementation in circuit QED structure, but future application will include photon detectors such as microwave kinetic inductance detectors. First we designed and fabricated half-wavelength coplanar waveguide resonators with niobium thin film on a high resistive silicon wafer, with the fundamental frequencies in the range of 1 to 8 GHz. The loaded quality factors are controlled by the coupling capacitors, and the lower bound of the intrinsic quality factor was measured down to 7 mK in the dilution refrigerator. We have also designed quarter-wavelength resonators and lumped LC resonators coupled to a transmission line, and characterized multiple resonators in a single transmission line. For the 3D transmon qubit application, we designed and fabricated a rectangular box resonator with superconducting aluminum. The intrinsic quality factor of the box resonator exceeds three million at 7 mK. We will also present basic results on the integration of a transmon qubit in the superconducting resonator.
In superconducting quantum processors, the predictability of device parameters is of increasing importance as many labs scale up their systems to larger sizes in a 3D-integrated architecture. In particular, the properties of superconducting resonators must be controlled well to ensure high-fidelity multiplexed readout of qubits. Here we present a method, based on conformal mapping techniques, to predict a resonator's parameters directly from its 2D cross-section, without computationally heavy and time-consuming 3D simulation. We demonstrate the method's validity by comparing the calculated resonator frequency and coupling quality factor with those obtained through 3D finite-element-method simulation and by measurement of 15 resonators in a flip-chip-integrated architecture. We achieve a discrepancy of less than 2% between designed and measured frequencies, for 6-GHz resonators. We also propose a design method that reduces the sensitivity of the resonant frequency to variations in the inter-chip spacing.
A wide variety of applications of microwave cavities, such as measurement and control of superconducting qubits, magnonic resonators, and phase noise filters, would be well served by having a highly tunable microwave resonance. Often this tunability is desired in situ at low temperatures, where one can take advantage of superconducting cavities. To date, such cryogenic tuning while maintaining a high quality factor has been limited to ∼500 MHz. Here we demonstrate a three-dimensional superconducting microwave cavity that shares one wall with a pressurized volume of helium. Upon pressurization of the helium chamber, the microwave cavity is deformed, which results in in situ tuning of its resonant frequency by more than 5 GHz, greater than 60% of the original 8 GHz resonant frequency. The quality factor of the cavity remains approximately constant at ≈7 × 103 over the entire range of tuning. As a demonstration of its usefulness, we implement a tunable cryogenic phase noise filter, which reduces the phase noise of our source by approximately 10 dB above 400 kHz.
In this paper, we present a novel design of a compact, double-fold half-wave superconducting coplanar waveguide resonator, specifically optimized for quantum readout. The geometry offers advantages in terms of scalability and allows for a more compact integration of qubits per unit area. The superconducting resonators are designed to operate within a fundamental frequency range of 1.9 GHz$-1.95GHz,utilizingbothgapandfingercouplingschemes.Thedevicesarefabricatedusingthinaluminumfilmsdepositedonhigh−resistivitysapphiresubstrates.Theproposedresonatorsexhibitqualityfactor(Q1.95 GHz, utilizing both gap and finger coupling schemes. The devices are fabricated using thin aluminum films deposited on high-resistivity sapphire substrates. The proposed resonators exhibit quality factor (Q1.95GHz,utilizingbothgapandfingercouplingschemes.Thedevicesarefabricatedusingthinaluminumfilmsdepositedonhigh−resistivitysapphiresubstrates.Theproposedresonatorsexhibitqualityfactor(Q_{L})of2.9×) of 2.9 ×)of2.9× 10^{5}$and 1.58 ×10310^{3}103for gap coupled and finger coupled, respectively, during experimental measurements. The simulated QL_{L}L​of single-folded meander line resonators are found to be 4.65 ×10510^{5}105and 258.42, for gap coupled and finger coupled, respectively, for comparison purpose at similar operating frequency. A comprehensive analysis of the microwave transmission spectra was conducted at cryogenic temperatures near 10 mK, across very high input drive powers ($-30dBmto30 dBm to30dBmto-10dBm).Experimentalresultsshowagoodagreementwithsimulationsandtheequivalentlumpedcircuitmodel.Notably,theproposeddesignreducesthephysicalfootprintoftheresonatordevicesupto28.210 dBm). Experimental results show a good agreement with simulations and the equivalent lumped circuit model. Notably, the proposed design reduces the physical footprint of the resonator devices up to 28.210dBm).Experimentalresultsshowagoodagreementwithsimulationsandtheequivalentlumpedcircuitmodel.Notably,theproposeddesignreducesthephysicalfootprintoftheresonatordevicesupto28.2\%comparedtoconventionalsingle−foldmeanderedstructures.TheresonatorsdemonstratestrongpotentialforintegratingqubitswithreadoutandcontrolbusesinquantuminformationprocessingwhichrequireaQcompared to conventional single-fold meandered structures. The resonators demonstrate strong potential for integrating qubits with readout and control buses in quantum information processing which require a Qcomparedtoconventionalsingle−foldmeanderedstructures.TheresonatorsdemonstratestrongpotentialforintegratingqubitswithreadoutandcontrolbusesinquantuminformationprocessingwhichrequireaQ_{L}$between10410^{4}104−-−10510^{5}105. They also being well-suited for cryogenic detector applications that utilize microwave kinetic inductance detector (MKID) arrays in frequency multiplexing for different coupling schemes.
Abstract Quantum computers (QC) have the potential to efficiently solve problems currently unfeasible on even the fastest generation of classical computers. The building block of a QC is a quantum bit (qubit). Encoding and reading qubit states coupled via high-Q resonant cavity modes is a solution to maintaining qubit states; however there is a need for simple, scalable and robust fabrication techniques capable of realizing high density cavity arrays. RadiaBeam is developing a novel approach utilizing metal additive manufacturing(AM) using both laser and electron beam powder bed fusion. Using a 6GHz quarter wave resonator (QWR), we fabricated several niobium and titanium alloy QWR cavities and characterized their superconducting RF performance. In this letter, we provide the details of the first 3D-printed qubit cavities design and fabrication, and compare their Q-factors, measured at dilution fridge temperatures, against the machined Nb resonators.
Superconducting quantum chips commonly utilize quarter-wavelength (λ/4) transmission line resonators as readout circuits. An analytical model for the accurate determination of resonance frequencies and coupling Q-factors of feedline-coupled superconducting resonators is introduced. The model leverages four-port microwave network analysis, integrating boundary conditions and conformal mapping techniques to compute even- and odd-mode impedances in edge-coupled coplanar waveguide (CPW) structures. Its versatility allows application to both planar and 3-D heterogeneous architectures, making it a powerful tool for resonator design. To validate the model, a test chip with λ/4 resonators of varying geometries is fabricated and measured in a cryogenic environment. Comparisons with finite element method (FEM) simulations and experimental measurements confirm the model's accuracy, with resonance frequencies and coupling Q-factors aligning closely across configurations. This proposed model facilitates the design of superconducting resonators in readout circuits for more effective, scalable, and adaptable quantum computing architectures.