Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1810.02404 · Review of Scientific Instruments

Cryogenic microwave filter cavity with a tunability greater than 5 GHz

Thomas J. Clark, Vaisakh Vadakkumbatt, Fabien Souris, Hugh Ramp, J. P. Davis

Published Nov 1, 2018• 15 citations
arXivHTMLPDF

Abstract

A wide variety of applications of microwave cavities, such as measurement and control of superconducting qubits, magnonic resonators, and phase noise filters, would be well served by having a highly tunable microwave resonance. Often this tunability is desired in situ at low temperatures, where one can take advantage of superconducting cavities. To date, such cryogenic tuning while maintaining a high quality factor has been limited to ∼500 MHz. Here we demonstrate a three-dimensional superconducting microwave cavity that shares one wall with a pressurized volume of helium. Upon pressurization of the helium chamber, the microwave cavity is deformed, which results in in situ tuning of its resonant frequency by more than 5 GHz, greater than 60% of the original 8 GHz resonant frequency. The quality factor of the cavity remains approximately constant at ≈7 × 103 over the entire range of tuning. As a demonstration of its usefulness, we implement a tunable cryogenic phase noise filter, which reduces the phase noise of our source by approximately 10 dB above 400 kHz.

DOI
10.1063/1.5051042

Related papers

Tuning a 3D microwave cavity via superfluid helium at millikelvin temperatures

Fabien Souris, H. Christiani, J. P. Davis

Frequency tunability of three dimensional (3D) microwave cavities opens up numerous possibilities for their use in hybrid quantum systems and related technologies. For many applications, it is desirable to tune the resonance at cryogenic temperatures without mechanical actuation. We show that a superconducting 3D microwave cavity can be tuned at the percent level by taking advantage of the dielectric properties of superfluid 4He at millikelvin temperatures, without affecting its intrinsic quality factor—reaching 3 × 105 in the present experiment.

arXiv:1707.09469•Applied Physics Letters•Oct 23, 2017•17 citations

Tunable Superconducting Cavity using Superconducting Quantum Interference Device Metamaterials

Samuel Kim, David B. Shrekenhamer, K. McElroy +2 more

Abstract Here we consider a tunable superconducting cavity that can be used either as a tunable coupler to a qubit inside the cavity or as a tunable low noise, low temperature, RF filter. Our design consists of an array of radio-frequency superconducting quantum interference devices (rf SQUIDs) inside a superconducting cavity. This forms a tunable metamaterial structure which couples to the cavity through its magnetic plasma frequency. By tuning the resonant frequency of the metamaterial through an applied magnetic flux, one can tune the cavity mode profile. This allows us to detune the cavity initially centered at 5.593 GHz by over 200 MHz. The maximum quality factor approaches that of the empty cavity, which is 4.5 × 106. The metamaterial electromagnetic response is controlled via a low-frequency or dc magnetic flux bias, and we present a control line architecture that is capable of applying sufficient magnetic flux bias with minimal parasitic coupling. Together this design allows for an in-situ tunable cavity which enables low-temperature quantum control applications.

Scientific Reports•Mar 15, 2019•13 citations

Applications of Superconducting Re-Entrant Microwave Cavities

Thomas J. Clark

This thesis describes the design, fabrication, and characterization of 3D superconducting microwave cavities for two applications. It first describes a cryogenically compatible microwave filter that is able to tune its resonant frequency by an unprecedented 5 GHz via deformation caused by a a helium pressure vessel. Then, it describes a novel microwave optomechanics device where such a cavity is coupled to an aluminized SiN membrane. It demonstrates that this device can be back-action cooled from the 450 mK base temperature of the cryostat down to 160 mK.

•Jan 1, 2019•0 citations

Piezoelectric tunable microwave superconducting cavity

Natália C. Carvalho, Yaohui Fan, Michael Edmund Tobar

In the context of engineered quantum systems, there is a demand for superconducting tunable devices, able to operate with high-quality factors at power levels equivalent to only a few photons. In this work, we developed a 3D microwave re-entrant cavity with such characteristics ready to provide a very fine-tuning of a high-Q resonant mode over a large dynamic range. This system has an electronic tuning mechanism based on a mechanically amplified piezoelectric actuator, which controls the resonator dominant mode frequency by changing the cavity narrow gap by very small displacements. Experiments were conducted at room and dilution refrigerator temperatures showing a large dynamic range up to 4 GHz and 1 GHz, respectively, and were compared to a finite element method model simulated data. At elevated microwave power input, nonlinear thermal effects were observed to destroy the superconductivity of the cavity due to the large electric fields generated in the small gap of the re-entrant cavity.

arXiv:1603.04848•Review of Scientific Instruments•Sep 1, 2016•23 citations

Niobium Tunable Microwave Filter

Rizwan Rafique, Thomas Ohki, Peter Linnér +1 more

A superconductor bandpass filter with tunable central frequency in the range of 2-3.5 GHz has been implemented using superconducting quantum interference devices (SQUIDs). The filter is designed using two pi-network resonators connected by a transmission line. Both resonators have a SQUID inductor with a tuning range of 65-200 pH, controlled by current magnetically coupled to the SQUIDs. Over a frequency tunability of 1.5 GHz, the filter has a mid-band insertion loss of 0.5-3.0 dB and corresponding maximum unloaded quality factor of 40. Due to the presence of active elements, tunability of the filter depends on the power of the microwave signal. A maximum power of -52 dBm corresponds to a frequency tuning range of 15%. Spectral measurements by controlling the central frequency of the filter with variable pulsewidth shows that the filter can be tuned at a rate of 120 GHz/mus.

IEEE Transactions on Microwave Theory and Techniques•Apr 15, 2009•9 citations

Design, Simulation, and Experimental Validation of 3D Resonant Cavities for CryoCMOS and Superconducting Qubit Readout

Beatriz Sacramento, Ednilson Lopes, Francisco P. M. Rouxinol

Three-dimensional microwave cavities are key components for superconducting-qubit readout and for the characterization of cryogenic microwave electronics [1]. In this work, we report the design, simulation, fabrication, and experimental validation of a rectangular 3D resonant cavity targeting operation near 5.4 GHz, compatible with the frequency range of CryoCMOS voltage-controlled oscillators (VCO). The cavity dimensions were obtained from analytical mode calculations, corrected for practical machining constraints, and validated using finite-element electromagnetic simulations in ANSYS HFSS. A split-block aluminum cavity was fabricated and characterized at room temperature using vector network analysis. The measured resonances agree with analytical and simulated predictions within sub-1% deviation, confirming the accuracy of the design procedure. Different SMA connector penetration configurations were experimentally investigated to evaluate the trade-off between loaded quality factor and transmission efficiency. The asymmetric $7 \mathrm{~mm} / 8 \mathrm{~mm}$ configuration provided the best compromise, yielding a loaded quality factor of approximately 3200 and improving the transmitted signal by about 20 dB compared with the symmetric $\mathrm{7 ~ m m} / \mathrm{7 ~ m m}$ configuration. These results demonstrate a reproducible design route for 3D cavities intended for CryoCMOS testing and future superconducting-qubit readout experiments.

Symposium on Microelectronics Technology and Devices•Aug 1, 2026•0 citations
A wide variety of applications of microwave cavities, such as measurement and control of superconducting qubits, magnonic resonators, and phase noise filters, would be well served by having a highly tunable microwave resonance. Often this tunability is desired in situ at low temperatures, where one can take advantage of superconducting cavities. To date, such cryogenic tuning while maintaining a high quality factor has been limited to ∼500 MHz. Here we demonstrate a three-dimensional superconducting microwave cavity that shares one wall with a pressurized volume of helium. Upon pressurization of the helium chamber, the microwave cavity is deformed, which results in in situ tuning of its resonant frequency by more than 5 GHz, greater than 60% of the original 8 GHz resonant frequency. The quality factor of the cavity remains approximately constant at ≈7 × 103 over the entire range of tuning. As a demonstration of its usefulness, we implement a tunable cryogenic phase noise filter, which reduces the phase noise of our source by approximately 10 dB above 400 kHz.
Frequency tunability of three dimensional (3D) microwave cavities opens up numerous possibilities for their use in hybrid quantum systems and related technologies. For many applications, it is desirable to tune the resonance at cryogenic temperatures without mechanical actuation. We show that a superconducting 3D microwave cavity can be tuned at the percent level by taking advantage of the dielectric properties of superfluid 4He at millikelvin temperatures, without affecting its intrinsic quality factor—reaching 3 × 105 in the present experiment.
Abstract Here we consider a tunable superconducting cavity that can be used either as a tunable coupler to a qubit inside the cavity or as a tunable low noise, low temperature, RF filter. Our design consists of an array of radio-frequency superconducting quantum interference devices (rf SQUIDs) inside a superconducting cavity. This forms a tunable metamaterial structure which couples to the cavity through its magnetic plasma frequency. By tuning the resonant frequency of the metamaterial through an applied magnetic flux, one can tune the cavity mode profile. This allows us to detune the cavity initially centered at 5.593 GHz by over 200 MHz. The maximum quality factor approaches that of the empty cavity, which is 4.5 × 106. The metamaterial electromagnetic response is controlled via a low-frequency or dc magnetic flux bias, and we present a control line architecture that is capable of applying sufficient magnetic flux bias with minimal parasitic coupling. Together this design allows for an in-situ tunable cavity which enables low-temperature quantum control applications.
This thesis describes the design, fabrication, and characterization of 3D superconducting microwave cavities for two applications. It first describes a cryogenically compatible microwave filter that is able to tune its resonant frequency by an unprecedented 5 GHz via deformation caused by a a helium pressure vessel. Then, it describes a novel microwave optomechanics device where such a cavity is coupled to an aluminized SiN membrane. It demonstrates that this device can be back-action cooled from the 450 mK base temperature of the cryostat down to 160 mK.
In the context of engineered quantum systems, there is a demand for superconducting tunable devices, able to operate with high-quality factors at power levels equivalent to only a few photons. In this work, we developed a 3D microwave re-entrant cavity with such characteristics ready to provide a very fine-tuning of a high-Q resonant mode over a large dynamic range. This system has an electronic tuning mechanism based on a mechanically amplified piezoelectric actuator, which controls the resonator dominant mode frequency by changing the cavity narrow gap by very small displacements. Experiments were conducted at room and dilution refrigerator temperatures showing a large dynamic range up to 4 GHz and 1 GHz, respectively, and were compared to a finite element method model simulated data. At elevated microwave power input, nonlinear thermal effects were observed to destroy the superconductivity of the cavity due to the large electric fields generated in the small gap of the re-entrant cavity.
A superconductor bandpass filter with tunable central frequency in the range of 2-3.5 GHz has been implemented using superconducting quantum interference devices (SQUIDs). The filter is designed using two pi-network resonators connected by a transmission line. Both resonators have a SQUID inductor with a tuning range of 65-200 pH, controlled by current magnetically coupled to the SQUIDs. Over a frequency tunability of 1.5 GHz, the filter has a mid-band insertion loss of 0.5-3.0 dB and corresponding maximum unloaded quality factor of 40. Due to the presence of active elements, tunability of the filter depends on the power of the microwave signal. A maximum power of -52 dBm corresponds to a frequency tuning range of 15%. Spectral measurements by controlling the central frequency of the filter with variable pulsewidth shows that the filter can be tuned at a rate of 120 GHz/mus.
Three-dimensional microwave cavities are key components for superconducting-qubit readout and for the characterization of cryogenic microwave electronics [1]. In this work, we report the design, simulation, fabrication, and experimental validation of a rectangular 3D resonant cavity targeting operation near 5.4 GHz, compatible with the frequency range of CryoCMOS voltage-controlled oscillators (VCO). The cavity dimensions were obtained from analytical mode calculations, corrected for practical machining constraints, and validated using finite-element electromagnetic simulations in ANSYS HFSS. A split-block aluminum cavity was fabricated and characterized at room temperature using vector network analysis. The measured resonances agree with analytical and simulated predictions within sub-1% deviation, confirming the accuracy of the design procedure. Different SMA connector penetration configurations were experimentally investigated to evaluate the trade-off between loaded quality factor and transmission efficiency. The asymmetric 7 mm/8 mm7 \mathrm{~mm} / 8 \mathrm{~mm}7 mm/8 mm configuration provided the best compromise, yielding a loaded quality factor of approximately 3200 and improving the transmitted signal by about 20 dB compared with the symmetric 7 mm/7 mm\mathrm{7 ~ m m} / \mathrm{7 ~ m m}7 mm/7 mm configuration. These results demonstrate a reproducible design route for 3D cavities intended for CryoCMOS testing and future superconducting-qubit readout experiments.