Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Review of Scientific Instruments

Spectral analysis of amplitude-modulated microwave signals with nitrogen-vacancy centers in diamond

Yang Zhitao, Feifei Zhou, Jianghang Yu, Hongwei Chen, Ying Dong, Xinqing Wang, Jun Li

Published Feb 1, 2026• 1 citation
Publisher

Abstract

Microwave (MW) magnetometry utilizing nitrogen-vacancy (NV) centers in diamond offers a broad, tunable detection bandwidth enabled by the magnetic-field-dependent electron spin resonances (ESR) of the NV centers. In this work, we present and experimentally demonstrate two NV-based protocols for spectral analysis of amplitude-modulated (MW) signals. The first protocol employs the NV center as a bandpass filter and reconstructs frequency-domain information of MW signals by sweeping the MW carrier frequency. The second protocol achieves optical imaging of the MW spectrum using an NV-based quantum spectrum analyzer, wherein a magnetic field gradient spatially maps the ESR frequencies of the NV centers, enabling parallel detection of multiple spectral components over a wide instantaneous bandwidth. Both protocols show results that agree well with reference measurements from a classical spectrum analyzer. Our approaches extend the application of spin-based quantum sensors to the field of modern communications and can be adapted for other spin-based quantum sensors.

DOI
10.1063/5.0312509

Related papers

Wide bandwidth instantaneous radio frequency spectrum analyzer based on nitrogen vacancy centers in diamond

Mayeul Chipaux, Loïc Toraille, C. Larat +4 more

We propose an original analog method to perform instantaneous and quantitative spectral analysis of microwave signals. An ensemble of nitrogen-vacancy (NV) centers held in a diamond plate is pumped by a 532 nm laser. Its photoluminescence is imaged through an optical microscope and monitored by a digital camera. An incoming microwave signal is converted into a microwave field in the area of the NV centers by a loop shaped antenna. The resonances induced by the magnetic component of that field are detected through a decrease of the NV centers photoluminescence. A magnetic field gradient induces a Zeeman shift of the resonances and transforms the frequency information into spatial information, which allows for the simultaneous analysis of the microwave signal in the entire frequency bandwidth of the device. The time dependent spectral analysis of an amplitude modulated microwave signal is demonstrated over a bandwidth of 600 MHz, associated to a frequency resolution of 7 MHz , and a refresh rate of 4 ms. With such integration time, a field of a few hundreds of μW can be detected. Since the optical properties of NV centers can be maintained even in high magnetic field, we estimate that an optimized device could allow frequency analysis in a range of 30 GHz, only limited by the amplitude of the magnetic field gradient. In addition, an increase of the NV centers quantity could lead both to an increase of the microwave sensitivity and to a decrease of the minimum refresh rate down to a few μs.

arXiv:1509.01395•Applied Physics Letters•Dec 7, 2015•60 citations

Imaging Frequency-Modulated Microwaves Using a Robust Quantum Spectrum Analyzer

Feifei Zhou, Yang Zhitao, Jae Su Yu +6 more

Spin-based quantum sensors have been applied to the quantum sensing of magnetic fields from DC to GHz with various schemes. The recently developed quantum spectrum analyzer (QSA) technique based on the nitrogen-vacancy (NV) centers in diamond shows an ultrawide frequency bandwidth in this application. Here, we improve this technique and develop a robust QSA via diamond engineering. This QSA exploits the electron spin resonance of NV centers in an engineered {111} industrial diamond, which cancels the complex process of magnetic arrangement and significantly enhances the robustness of QSA against spin mixing under high magnetic fields in practice. A tunable frequency bandwidth of up to 18 GHz with a maximum instantaneous bandwidth of 2 GHz is achieved as well as a frequency resolution of several MHz and a large dynamic range of 65 dB. Using this QSA, we realize the optical imaging of frequency-modulated microwaves. Our work provides a promising rapid-deployment architecture for QSA and extends its application to spectral analysis in modern communications.

ACS Photonics•Nov 26, 2025•1 citation

High-frequency resolution diamond nitrogen-vacancy center wide-spectrum imaging technology

Yuanyuan Shen, Bo Wang, Dongqian Ke +10 more

High-resolution wide-spectrum measurement techniques have important applications in fields such as astronomy, wireless communication, and medical imaging. Nitrogen-vacancy (NV) center in diamond is well known for its high stability, high sensitivity, real-time monitoring, single-point detection, and suitability for long-term measurement, and has an outstanding choice for spectrum analyzers. Currently, spectrum analyzers based on NV centers as detectors can perform real-time spectrum analysis in the range of several tens of gigahertz, but their frequency resolution is limited to a MHz level. In this study, we construct a quantum diamond microwave spectrum imaging system by combining continuous wave-mixing techniques. According to the spin-related properties of the NV center in diamond, we implement optical pumping by 532 nm green laser light illuminating the diamond NV center. A spherical magnet is used to produce a magnetic field gradient along the direction of the diamond crystal. By adjusting the size and direction of the magnetic field gradient, spatial encoding of the resonance frequency of the NV center is achieved. The magnetic field gradient induces the Zeeman effect on the diamond surface at different positions, generating corresponding ODMR signals. Through accurate programming, we coordinate the frequency scanning step size of the microwave source with the camera exposure and image storage time, and synchronize them circularly according to the order of image acquisition. Ultimately, after algorithmic processing, we successfully obtain comprehensive spectrum data in a range from 900 MHz to 6.0 GHz. Within the measurable spectrum range, the system employs continuous wave-mixing, simultaneously applying resonant microwaves and slightly detuning auxiliary microwaves to effectively excite the NV center. This method triggers off microwave interference effects, disrupting the balance between laser-induced polarization and microwave-induced spontaneous relaxation. Specifically, microwave interference causes the phase and amplitude of the fluorescence signal to change, leading to the generation of alternating current fluorescence signals. This further enhances the response of the NV magnetometer to weak microwave signals. The method enables the system to achieve a frequency resolution of 1 Hz in the measurable spectrum range, and it can separately measure the frequency resolution of multiple frequency points with a frequency step size of 1 MHz. The research results indicate that the wide-spectrum measurement based on NV centers can achieve sub-hertz frequency resolution, providing robust technical support for future spectrum analysis and applications.

Acta Physica Sinica•Jan 1, 2024•1 citation

System for the remote control and imaging of MW fields for spin manipulation in NV centers in diamond

Giacomo Mariani, Shuhei Nomoto, Satoshi Kashiwaya +1 more

Nitrogen-vacancy (NV) centers in diamond have been used as platforms for quantum information, magnetometry and imaging of microwave (MW) fields. The spatial distribution of the MW fields used to drive the electron spin of NV centers plays a key role for these applications. Here, we report a system for the control and characterization of MW magnetic fields used for the NV spin manipulation. The control of the MW field in the vicinity of a diamond surface is mediated by an exchangeable lumped resonator, coupled inductively to a MW planar ring antenna. The characterization of the MW fields in the near-field is performed by an FFT imaging of Rabi oscillations, by using an ensemble of NV centers. We have found that the Rabi frequency over a lumped resonator is enhanced 22 times compared to the Rabi frequency without the presence of the lumped resonator. Our system may find applications in quantum information and magnetometry where a precise and controlled spin manipulation is required, showing NV centers as good candidates for imaging MW fields and characterization of MW devices.

Scientific Reports•Mar 16, 2020•46 citations

Simultaneous Identification of Multiple Microwave Signals in 313-MHz Continuous Bandwidth Using Nitrogen-Vacancy Centers in Diamond

Y. W. Jin, Huan Fei Wen, Ding Wang +8 more

The efficient and reliable detection of microwave signals is a key element of the breakthrough in new-generation communication technology. In this article, we proposed an approach for the simultaneous identification of multiple microwave signals in a continuous frequency range based on the spectral hole-burning effect of nitrogen-vacancy (NV) centers. The protocol combines the quantum wide-field imaging method with magnetic gradient means, breaking the narrowband and discrete detection limitations of conventional optically detected magnetic resonance (ODMR) techniques. The frequencies of multiple microwave signals can be accurately decoupled by locating the relevant gaps on resonance frequency curves. Meanwhile, the effects induced by fixed-frequency signals with different powers on the resonance frequency curves were systematically analyzed. The experimental results indicated that the system realized a multiple-frequency resolution of 1 MHz and a minimum detectable power of 1 mW over a continuous bandwidth of 313-MHz. This proposal is capable of real-time and simultaneous detection of multiple microwave signals, which remarkably improves the utilization efficiency of spectrum resources.

IEEE Transactions on Microwave Theory and Techniques•Jul 30, 2024•0 citations

A nanoscale magnetic spectrum analyzer based on qubit dressed states

Jan Hendrik Rueschkamp, Shantam Ravan, Daniel Fernandez +6 more

Magnetic field fluctuations on nanometer length scales manifest in a diverse range of phenomena -- electron and spin dynamics in materials and devices, quantum many-body systems, and molecular chemistry. Measuring these phenomena requires sensors with a challenging combination of broad spectral bandwidth, high sensitivity, and nanoscale spatial resolution. Nitrogen-vacancy (NV) centers, atom-like quantum sensors in diamond, possess the requisite sensitivity and nanoscale sensing volume, but are typically limited in bandwidth by the practical speed of the applied quantum control sequence. Here, we overcome this limitation by exposing the NV qubit to a microwave dressing field during a dynamical decoupling sequence, which both amplifies and frequency-mixes target signals at arbitrary frequencies into the detection band of the dynamical decoupling protocol. We demonstrate this approach by using NV centers to detect both coherent and noisy nanoscale spin wave dynamics in a magnetic yttrium-iron-garnet (YIG) thin film over a broad frequency range. Our technique generalizes to other qubit platforms, providing a versatile framework for nanoscale spectroscopy across diverse physical and chemical systems.

arXiv:2606.05426•Jun 3, 2026•0 citations
Microwave (MW) magnetometry utilizing nitrogen-vacancy (NV) centers in diamond offers a broad, tunable detection bandwidth enabled by the magnetic-field-dependent electron spin resonances (ESR) of the NV centers. In this work, we present and experimentally demonstrate two NV-based protocols for spectral analysis of amplitude-modulated (MW) signals. The first protocol employs the NV center as a bandpass filter and reconstructs frequency-domain information of MW signals by sweeping the MW carrier frequency. The second protocol achieves optical imaging of the MW spectrum using an NV-based quantum spectrum analyzer, wherein a magnetic field gradient spatially maps the ESR frequencies of the NV centers, enabling parallel detection of multiple spectral components over a wide instantaneous bandwidth. Both protocols show results that agree well with reference measurements from a classical spectrum analyzer. Our approaches extend the application of spin-based quantum sensors to the field of modern communications and can be adapted for other spin-based quantum sensors.
We propose an original analog method to perform instantaneous and quantitative spectral analysis of microwave signals. An ensemble of nitrogen-vacancy (NV) centers held in a diamond plate is pumped by a 532 nm laser. Its photoluminescence is imaged through an optical microscope and monitored by a digital camera. An incoming microwave signal is converted into a microwave field in the area of the NV centers by a loop shaped antenna. The resonances induced by the magnetic component of that field are detected through a decrease of the NV centers photoluminescence. A magnetic field gradient induces a Zeeman shift of the resonances and transforms the frequency information into spatial information, which allows for the simultaneous analysis of the microwave signal in the entire frequency bandwidth of the device. The time dependent spectral analysis of an amplitude modulated microwave signal is demonstrated over a bandwidth of 600 MHz, associated to a frequency resolution of 7 MHz , and a refresh rate of 4 ms. With such integration time, a field of a few hundreds of μW can be detected. Since the optical properties of NV centers can be maintained even in high magnetic field, we estimate that an optimized device could allow frequency analysis in a range of 30 GHz, only limited by the amplitude of the magnetic field gradient. In addition, an increase of the NV centers quantity could lead both to an increase of the microwave sensitivity and to a decrease of the minimum refresh rate down to a few μs.
Spin-based quantum sensors have been applied to the quantum sensing of magnetic fields from DC to GHz with various schemes. The recently developed quantum spectrum analyzer (QSA) technique based on the nitrogen-vacancy (NV) centers in diamond shows an ultrawide frequency bandwidth in this application. Here, we improve this technique and develop a robust QSA via diamond engineering. This QSA exploits the electron spin resonance of NV centers in an engineered {111} industrial diamond, which cancels the complex process of magnetic arrangement and significantly enhances the robustness of QSA against spin mixing under high magnetic fields in practice. A tunable frequency bandwidth of up to 18 GHz with a maximum instantaneous bandwidth of 2 GHz is achieved as well as a frequency resolution of several MHz and a large dynamic range of 65 dB. Using this QSA, we realize the optical imaging of frequency-modulated microwaves. Our work provides a promising rapid-deployment architecture for QSA and extends its application to spectral analysis in modern communications.
High-resolution wide-spectrum measurement techniques have important applications in fields such as astronomy, wireless communication, and medical imaging. Nitrogen-vacancy (NV) center in diamond is well known for its high stability, high sensitivity, real-time monitoring, single-point detection, and suitability for long-term measurement, and has an outstanding choice for spectrum analyzers. Currently, spectrum analyzers based on NV centers as detectors can perform real-time spectrum analysis in the range of several tens of gigahertz, but their frequency resolution is limited to a MHz level. In this study, we construct a quantum diamond microwave spectrum imaging system by combining continuous wave-mixing techniques. According to the spin-related properties of the NV center in diamond, we implement optical pumping by 532 nm green laser light illuminating the diamond NV center. A spherical magnet is used to produce a magnetic field gradient along the direction of the diamond crystal. By adjusting the size and direction of the magnetic field gradient, spatial encoding of the resonance frequency of the NV center is achieved. The magnetic field gradient induces the Zeeman effect on the diamond surface at different positions, generating corresponding ODMR signals. Through accurate programming, we coordinate the frequency scanning step size of the microwave source with the camera exposure and image storage time, and synchronize them circularly according to the order of image acquisition. Ultimately, after algorithmic processing, we successfully obtain comprehensive spectrum data in a range from 900 MHz to 6.0 GHz. Within the measurable spectrum range, the system employs continuous wave-mixing, simultaneously applying resonant microwaves and slightly detuning auxiliary microwaves to effectively excite the NV center. This method triggers off microwave interference effects, disrupting the balance between laser-induced polarization and microwave-induced spontaneous relaxation. Specifically, microwave interference causes the phase and amplitude of the fluorescence signal to change, leading to the generation of alternating current fluorescence signals. This further enhances the response of the NV magnetometer to weak microwave signals. The method enables the system to achieve a frequency resolution of 1 Hz in the measurable spectrum range, and it can separately measure the frequency resolution of multiple frequency points with a frequency step size of 1 MHz. The research results indicate that the wide-spectrum measurement based on NV centers can achieve sub-hertz frequency resolution, providing robust technical support for future spectrum analysis and applications.
Nitrogen-vacancy (NV) centers in diamond have been used as platforms for quantum information, magnetometry and imaging of microwave (MW) fields. The spatial distribution of the MW fields used to drive the electron spin of NV centers plays a key role for these applications. Here, we report a system for the control and characterization of MW magnetic fields used for the NV spin manipulation. The control of the MW field in the vicinity of a diamond surface is mediated by an exchangeable lumped resonator, coupled inductively to a MW planar ring antenna. The characterization of the MW fields in the near-field is performed by an FFT imaging of Rabi oscillations, by using an ensemble of NV centers. We have found that the Rabi frequency over a lumped resonator is enhanced 22 times compared to the Rabi frequency without the presence of the lumped resonator. Our system may find applications in quantum information and magnetometry where a precise and controlled spin manipulation is required, showing NV centers as good candidates for imaging MW fields and characterization of MW devices.
The efficient and reliable detection of microwave signals is a key element of the breakthrough in new-generation communication technology. In this article, we proposed an approach for the simultaneous identification of multiple microwave signals in a continuous frequency range based on the spectral hole-burning effect of nitrogen-vacancy (NV) centers. The protocol combines the quantum wide-field imaging method with magnetic gradient means, breaking the narrowband and discrete detection limitations of conventional optically detected magnetic resonance (ODMR) techniques. The frequencies of multiple microwave signals can be accurately decoupled by locating the relevant gaps on resonance frequency curves. Meanwhile, the effects induced by fixed-frequency signals with different powers on the resonance frequency curves were systematically analyzed. The experimental results indicated that the system realized a multiple-frequency resolution of 1 MHz and a minimum detectable power of 1 mW over a continuous bandwidth of 313-MHz. This proposal is capable of real-time and simultaneous detection of multiple microwave signals, which remarkably improves the utilization efficiency of spectrum resources.
Magnetic field fluctuations on nanometer length scales manifest in a diverse range of phenomena -- electron and spin dynamics in materials and devices, quantum many-body systems, and molecular chemistry. Measuring these phenomena requires sensors with a challenging combination of broad spectral bandwidth, high sensitivity, and nanoscale spatial resolution. Nitrogen-vacancy (NV) centers, atom-like quantum sensors in diamond, possess the requisite sensitivity and nanoscale sensing volume, but are typically limited in bandwidth by the practical speed of the applied quantum control sequence. Here, we overcome this limitation by exposing the NV qubit to a microwave dressing field during a dynamical decoupling sequence, which both amplifies and frequency-mixes target signals at arbitrary frequencies into the detection band of the dynamical decoupling protocol. We demonstrate this approach by using NV centers to detect both coherent and noisy nanoscale spin wave dynamics in a magnetic yttrium-iron-garnet (YIG) thin film over a broad frequency range. Our technique generalizes to other qubit platforms, providing a versatile framework for nanoscale spectroscopy across diverse physical and chemical systems.