Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Fiber optics for quantum computers

Steve Helsby, Hebe Powell, Péter Horák, Bruce G. Klappauf, Peter G. Kazansky

Published Jan 1, 2004• 0 citations
OpenAlex

Abstract

Abstract: We describe schemes for the integration of miniature optical components onto Atom Chips, for the manipulation and detection of ultra-cold atoms. Our intention is to build detectors sensitive enough to accurately detect single atoms. Two approaches are discussed: simple fluorescence detection and the use of a resonant cavity. Theory predicts that cavities with F>100 should be sufficient to obtain signal to noise ratios high enough to detect single atoms. The first micro cavities were demonstrated using mirrors formed by cleaved fiber ends coated with a stick-on dielectric coating to give F ∼100. A more successful approach involves the full integration of the mirrors and fibers by using Bragg gratings written into the fiber core: it has been possible to form gap cavities with F ~ 150. 1.

Related papers

The integration of fibre optics for atom chips

Stephen John Helsby

This thesis reports on the progress made towards the integration of fibre optics components for the atom chip, a device developed to manipulate matter on the atomic scale for the purpose of quantum information processing, novel applications, and fundamental research. Following in the direction of the electronics industry, miniaturisation has resulted in exquisite control of cold atoms above surfaces, allowing the vision of a matter wave toolbox to come closer to fruition. However, although the size of the components necessary for guiding atoms via magnetic or electrostatic fields has been greatly reduced, there is still a need to scale down the optical components. The development of these cavities is detailed in this thesis, from early use of evaporated gold coated mirrors to the fully integral solution of photorefractive Bragg gratings. In addition to a thorough analysis of the optical properties of these fibre gap cavities, experimental results indicate that these gap cavity devices can be constructed with the sensitivity necessary for single atom detection.

•Mar 1, 2008•0 citations

Detecting neutral atoms on an atom chip

M. Wilzbach, A. Haase, M. Schwarz +8 more

Abstract Detecting single atoms (qubits) is a key requirement for implementing quantum information processing on an atom chip. The detector should ideally be integrated on the chip. Here we present and compare different methods capable of detecting neutral atoms on an atom chip. After a short introduction to fluorescence and absorption detection we discuss cavity enhanced detection of single atoms. In particular we concentrate on optical fiber based detectors such as fiber cavities and tapered fiber dipole traps. We discuss the various constraints in building such detectors in detail along with the current implementations on atom chips. Results from experimental tests of fiber integration are also described. In addition we present a pilot experiment for atom detection using a concentric cavity to verify the required scaling.

arXiv:physics/0608189•Fortschritte der Physik•Aug 1, 2006•12 citations

Detecting Neutral Atoms on an Atom Chip

Marco Wilzbach, Albrecht Haase, Michael Schwarz +8 more

This chapter contains sections titled: Introduction Detecting Single Atoms Measuring the Scattered Light: Fluorescence Detection Measuring the Driving Field Absorption on Resonance Refraction Cavities Absorption on Resonance Refraction Many Atoms in a Cavity Concentric Cavity Miniaturization Properties of Fiber Cavities Loss Mechanisms for a Cavity Losses due to the Gap Length Losses due to Transversal Misalignment Losses due to Angular Misalignment Fresnel Reflections Other Fiber Optical Components for the Atom Chip Fluorescence and Absorption Detectors A Single Mode Tapered Lensed Fiber Dipole Trap Integration of Fibers on the Atom Chip Building Fiber Cavities The SU-8 Resist Test of the SU-8 Structure Pilot Test for Atom Detection with Small Waists Dropping Atoms through a Concentric Cavity Detecting Magnetically Guided Atoms Conclusion References

Wiley eBooks•Jan 26, 2007•1 citation

Fibre optics for atom detection

Steve Helsby, Péter Horák, Peter G. Kazansky

The paper reports on standard fibre optical components mounted onto the chip for single atom detection. At present, two main directions are being pursued: fluorescence detection and fibre Fabry-Perot gap cavities. Theoretical analysis has shown that both devices will have the ability to detect single atoms with the micro-cavities offering the possibility of non-destructive detection.

European Quantum Electronics Conference (EQEC)•Jan 18, 2006•0 citations

Fiber Bragg gratings for atom chips

Steve Helsby, Costantino Corbari, Morten Ibsen +2 more

We discuss the fabrication and characterization of fiber Fabry-Perot cavities developed for integrated atom detection on the atom chip. Investigations show that the cavities are suitable for the detection of small numbers of atoms, with restrictions due to absorption in the Bragg gratings. We show that a significant reduction in these absorption losses can be attained by thermal annealing, removing any material limitations to single-atom detection.

Physical Review A•Jan 17, 2007•3 citations

Single atom detection on an atom chip with integrated optics

Marco Wilzbach

The subject of this thesis is the miniaturization and integration of detectors for the detection of single rubidium atoms on an atom chip. For this purpose three different detectors were developed for atom detection by absorption or fluorescence: i) A fluorescence detector was realized by mounting a tapered lensed fiber perpendicular to a collection fiber. ii) An absorption detector was built by placing a multi-mode fiber in-line with a tapered lensed fiber. iii) A tunable cavity detector was built from two single mode fibers mounted on the chip surface. To mount the detectors on the planar surface of the atom chip retaining structures by means of lithographical techniques were developed. Those structures allow a very accurate and stable passive fiber alignment. To test the individual detectors an atomic ensemble of thermal rubidium atoms was prepared in a magneto-optical trap. Then the atoms were transferred into magnetic micro-traps of the atom chip and were guided to one of the detectors. Each integrated detector has been evaluated by several characterization measurements. With the fluorescence detector the highest single atom detection efficiency of 54\\% was attained. Thereby it was possible to perform quantitative measurements for the magnetically guided atoms on a single atom level and to study fundamental properties of the confined atoms.

•Jan 1, 2007•0 citations
Abstract: We describe schemes for the integration of miniature optical components onto Atom Chips, for the manipulation and detection of ultra-cold atoms. Our intention is to build detectors sensitive enough to accurately detect single atoms. Two approaches are discussed: simple fluorescence detection and the use of a resonant cavity. Theory predicts that cavities with F>100 should be sufficient to obtain signal to noise ratios high enough to detect single atoms. The first micro cavities were demonstrated using mirrors formed by cleaved fiber ends coated with a stick-on dielectric coating to give F ∼100. A more successful approach involves the full integration of the mirrors and fibers by using Bragg gratings written into the fiber core: it has been possible to form gap cavities with F ~ 150. 1.
This thesis reports on the progress made towards the integration of fibre optics components for the atom chip, a device developed to manipulate matter on the atomic scale for the purpose of quantum information processing, novel applications, and fundamental research. Following in the direction of the electronics industry, miniaturisation has resulted in exquisite control of cold atoms above surfaces, allowing the vision of a matter wave toolbox to come closer to fruition. However, although the size of the components necessary for guiding atoms via magnetic or electrostatic fields has been greatly reduced, there is still a need to scale down the optical components. The development of these cavities is detailed in this thesis, from early use of evaporated gold coated mirrors to the fully integral solution of photorefractive Bragg gratings. In addition to a thorough analysis of the optical properties of these fibre gap cavities, experimental results indicate that these gap cavity devices can be constructed with the sensitivity necessary for single atom detection.
Abstract Detecting single atoms (qubits) is a key requirement for implementing quantum information processing on an atom chip. The detector should ideally be integrated on the chip. Here we present and compare different methods capable of detecting neutral atoms on an atom chip. After a short introduction to fluorescence and absorption detection we discuss cavity enhanced detection of single atoms. In particular we concentrate on optical fiber based detectors such as fiber cavities and tapered fiber dipole traps. We discuss the various constraints in building such detectors in detail along with the current implementations on atom chips. Results from experimental tests of fiber integration are also described. In addition we present a pilot experiment for atom detection using a concentric cavity to verify the required scaling.
This chapter contains sections titled: Introduction Detecting Single Atoms Measuring the Scattered Light: Fluorescence Detection Measuring the Driving Field Absorption on Resonance Refraction Cavities Absorption on Resonance Refraction Many Atoms in a Cavity Concentric Cavity Miniaturization Properties of Fiber Cavities Loss Mechanisms for a Cavity Losses due to the Gap Length Losses due to Transversal Misalignment Losses due to Angular Misalignment Fresnel Reflections Other Fiber Optical Components for the Atom Chip Fluorescence and Absorption Detectors A Single Mode Tapered Lensed Fiber Dipole Trap Integration of Fibers on the Atom Chip Building Fiber Cavities The SU-8 Resist Test of the SU-8 Structure Pilot Test for Atom Detection with Small Waists Dropping Atoms through a Concentric Cavity Detecting Magnetically Guided Atoms Conclusion References
The subject of this thesis is the miniaturization and integration of detectors for the detection of single rubidium atoms on an atom chip. For this purpose three different detectors were developed for atom detection by absorption or fluorescence: i) A fluorescence detector was realized by mounting a tapered lensed fiber perpendicular to a collection fiber. ii) An absorption detector was built by placing a multi-mode fiber in-line with a tapered lensed fiber. iii) A tunable cavity detector was built from two single mode fibers mounted on the chip surface. To mount the detectors on the planar surface of the atom chip retaining structures by means of lithographical techniques were developed. Those structures allow a very accurate and stable passive fiber alignment. To test the individual detectors an atomic ensemble of thermal rubidium atoms was prepared in a magneto-optical trap. Then the atoms were transferred into magnetic micro-traps of the atom chip and were guided to one of the detectors. Each integrated detector has been evaluated by several characterization measurements. With the fluorescence detector the highest single atom detection efficiency of 54\\% was attained. Thereby it was possible to perform quantitative measurements for the magnetically guided atoms on a single atom level and to study fundamental properties of the confined atoms.