Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Microwave and Wireless Technology Letters

An Ultrawideband Cryogenic LNA in 40-nm CMOS for Multiple Spin/Superconducting Qubit Readout

Mahesh Kumar Chaubey, Yin‐Cheng Chang, Po‐Chang Wu, Hann-Huei Tsai, Shawn S. H. Hsu

Published Nov 24, 2025• 2 citations
Publisher

Abstract

This letter presents an ultrawideband cryogenic low-noise amplifier (LNA) with current reuse and stacked inverter-based input-referred noise (IRN) cancellation in 40-nm CMOS. The first stage utilizes an IRN reduction high-$Q$gate inductor with current reuse, a stacked inverter-based shunt-resistive feedback input stage, and a cryogenically aware back-gate biasing technique to regulate the threshold voltage under cryogenic operation. The second stage is the common-source (CS) main amplifier, followed by a cascode current-reuse auxiliary amplifier to suppress the channel thermal noise of the main amplifier. The third stage is the current-reuse CS inverter-based postamplifier buffer stage. At 4 K, the LNA achieves a measured peak gain (${S} _{21}$) of 37 dB, with a large 3-dB bandwidth (BW) from 0.15 to 8 GHz and aNFminof 0.4 dB at 3.2 GHz under${P} _{\mathrm {DC}}$of 13.2 mW. To our knowledge, the proposed LNA achieves the BW bandwidth and the figure of merit (FoM) among the highest compared to published CMOS LNAs operating at 4 K. The proposed LNA is suitable for both spin and superconducting qubit readout.

DOI
10.1109/lmwt.2025.3631887

Related papers

A 7.3–9.5-GHz Cryogenic LNA Based on Passive Noise Cancellation for Qubit State Readout

Yaoyu Li, Yanshu Guo, Tian Tian +4 more

A cryogenic low-voltage, broadband low-noise amplifier(LNA) has been designed for qubit state readout systems. The proposed LNA utilizes passive components for noise cancellation. A tri-coupled transformer is utilized to simultaneously achieve broadband input impedance matching and noise matching. Additionally, it incorporates capacitive feedback and an in-phase transformer to effectively cancel noise. Implemented in 28-nm bulk CMOS technology and verified at 10 K, the LNA achieves a maximum gain of 26.7 dB, a −3-dB bandwidth of 2.2 GHz, a lowest noise temperature (NT) of 25 K, a power consumption of 4.05 mW at 0.6-V supply voltage, and a figure of merit (FoM) of 0.12 dB/mW/ph, which is comparable with the recent works.

IEEE Microwave and Wireless Technology Letters•May 26, 2025•2 citations

A 4–8 GHz GaAs LNA with 15K Noise Temperature for Superconducting Qubit Readout

Zhe Wang, Ruihao Yin, Hua Chen

This paper presents a cryogenic low-noise amplifier designed for superconducting qubit readout in quantum computing systems. The proposed LNA adopts a three-stage cascaded to achieve a balanced trade-off between gain and noise. Moreover, optimized inter-stage matching is also used. At 300K, the LNA exhibits a bandwidth of 4–8 GHz with a gain ranging from 33 to 35 dB, and a noise figure of 1.5 dB at 6 GHz. At 4K, it delivers over 32 dB gain across 4-8 GHz with noise temperature below 20K (minimum 15K), while power only 12 mW. Additionally, this C-band cryogenic MMIC LNA is designed in a 250 nm GaAs pHEMT process.

International Conference on Microwave and Millimeter Wave Technology (ICMMT)•May 1, 2026•0 citations

A 5.5-7.9 GHz Double Quadrature Cryo-CMOS Receiver Featuring a Wideband Noise Matching LNA for Quantum Applications

Zixun Gao, Chenglong Liang, Suyuan Gan +5 more

This work introduces a broadband cryogenic receiver for scalable multiplexed readout of qubits. The receiver utilizes a double quadrature architecture with amplitude and phase error suppression. The hybrid poly-phase filter (PPF) is applied in the architecture to further reduce the input amplitude and phase errors at the radio frequency (RF) end, enhancing the circuit's overall error vector magnitude (EVM). To address the issue of wide bandwidth (BW) for qubit expansion, a low noise amplifier (LNA) with broadband input and noise matching and an improved four-input intermediate frequency amplifier (IF-AMP) with a resistance feedback structure are proposed, achieving a broadband gain response with high flatness. The chip has been designed in standard 55 nm CMOS technology. The LNA achieves a measured power gain of 27.4 dB at 5 GHz with a -3 dB BW of 5.2 GHz at 6 K. Across the entire band of interest, the measured noise figure (NF) deviates by just 0.15 dB from the minimum noise figure (NFmin) and less than 2 dB at 300K, while the measured cryogenic NF falls within the range of 0.79-1 dB. The LNA consumes only 5.5 mW from a 1.2 V supply. Simulation results of the designed receiver indicate that it delivers an average gain of 49.5 dB with a -3 dB BW of 2.4 GHz and an image rejection ratio (IRR) exceeding 40 dB at 300 K.

IEEE International Symposium on Circuits and Systems proceedings•May 25, 2025•2 citations

A C-band cryogenic gallium arsenide low-noise amplifier for quantum applications

Ziqing Guo, Daxiong Sun, Peisheng Huang +16 more

Large-scale superconducting quantum computers require massive numbers of high-performance cryogenic low-noise amplifiers (cryo-LNAs) for qubit readout. Here we presented a C-band monolithic microwave integrated circuit (MMIC) cryo-LNA for this purpose. This cryo-LNA is based on a 150 nm gallium arsenide (GaAs) pseudomorphic high electron mobility transistor (pHEMT) process and implemented with a three-stage cascaded architecture, where the first stage adopts careful impedance matching to optimize the noise and return loss. The integration of negative feedback loops adopted in the second and third stages enhances the overall stability. Moreover, the pHEMT self-bias and current multiplexing circuitry structure facilitate the reduction of power consumption and require only a single bias line. Operating at an ambient temperature of 3.6 K and consuming 15 mW, the cryo-LNA demonstrates good performance in the C-band, reaching a minimum noise temperature of 4 K and an average gain of 40 dB. We further benchmarked this cryo-LNA with superconducting qubits, achieving an average single-shot dispersive readout fidelity of 98.3% without assistance from a quantum-limited parametric amplifier. The development of GaAs cryo-LNA diversifies technical support necessary for large-scale quantum applications.

arXiv:2412.19477•Chip•Apr 6, 2025•3 citations

A 65-nm Cryo-CMOS-Based 4–7-GHz Wideband Noise-Canceling Receiver for Superconducting Multi-Qubits Readout

Juhui Jeong, Hyeonsik Ahn, Junhyeop Kim +5 more

This paper presents a 4–7GHz cryogenic readout integrated circuit (ROIC) implemented in a 65-nm CMOS process for superconducting multi-qubit readout. The proposed ROIC front-end employs a transformer (TF)-based dual-path noise-canceling low-noise amplifier and a TF-based current-bleeding active mixer to enhance gain while suppressing thermal and flicker noise. To realize a wide dynamic range and a large intermediate frequency (IF) bandwidth, a dB-linear broadband (435MHz) variable-gain amplifier with an active-RC feedback topology is employed for multi-qubit sensing. The fabricated ROIC operates at a cryogenic temperature (13K), achieving a maximum gain of 70.4dB and a minimum noise figure of 0.41dB (29K noise temperature) over 435MHz IF bandwidth. The input 1-dB compression point and the input third-order intercept point reach–59.8dBm and–50.4dBm at the maximum gain setting, and–29.8dBm and–20.7dBm at the minimum gain setting, respectively. The ROIC achieves a spurious-free dynamic range of 30.8dB and 50.6dB at maximum and minimum gain settings, respectively, demonstrating competitive performance among reported cryogenic ROICs. The prototype consumes 16.3mW from a 1.2-V supply at 13K with an active area of 1.45 mm2.

IEEE Transactions on Circuits and Systems I Regular Papers•Jan 1, 2026•0 citations

A 1.15 mW SiGe BiCMOS Cryogenic LNA for Superconducting Qubit Readout with 4.5 K Noise Temperature From 4 to 9 GHz

Aleksei Nerushenko, Roc Berenguer, Alvaro Urain +1 more

This work presents the design and post-layout simulation of a cryogenic SiGe BiCMOS low-noise amplifier (LNA) for superconducting transmon-qubit readout in quantum processors scaling beyond hundreds of qubits. The target specifications are first established and justified by surveying state-of-the-art of cryogenic LNAs and modeling the dispersive qubit readout process. The LNA is implemented with three cascaded stages in common-emitter configuration and employs tuned inductive matching and parallel peaking networks in each stage to optimize noise, gain flatness, and bandwidth while maintaining minimal DC power consumption. The amplifier draws only 1.15 mW from a 0.15 V supply and occupies$0.252 \text{mm}^{2}$. Post-layout simulations confirm input/output S-parameter matching better than$-10 \text{dB}, 41-44 \text{dB}$gain with$<3 \text{dB}$ripple,$<5 \mathrm{K}$noise temperature across$4-9 \text{GHz}$, and a worst-case OP1 dB compression point of$\mathbf{- 1 9. 9 6. 6 d B m}$. A comparative analysis demonstrates that SiGe BiCMOS offers a favorable trade-off between InP HEMT's low noise and CMOS's integration potential for large-scale quantum processors.

Conference on Design of Circuits and Integrated Systems•Nov 26, 2025•1 citation
This letter presents an ultrawideband cryogenic low-noise amplifier (LNA) with current reuse and stacked inverter-based input-referred noise (IRN) cancellation in 40-nm CMOS. The first stage utilizes an IRN reduction high-QQQgate inductor with current reuse, a stacked inverter-based shunt-resistive feedback input stage, and a cryogenically aware back-gate biasing technique to regulate the threshold voltage under cryogenic operation. The second stage is the common-source (CS) main amplifier, followed by a cascode current-reuse auxiliary amplifier to suppress the channel thermal noise of the main amplifier. The third stage is the current-reuse CS inverter-based postamplifier buffer stage. At 4 K, the LNA achieves a measured peak gain (S21{S} _{21}S21​) of 37 dB, with a large 3-dB bandwidth (BW) from 0.15 to 8 GHz and aNFminof 0.4 dB at 3.2 GHz underPDC{P} _{\mathrm {DC}}PDC​of 13.2 mW. To our knowledge, the proposed LNA achieves the BW bandwidth and the figure of merit (FoM) among the highest compared to published CMOS LNAs operating at 4 K. The proposed LNA is suitable for both spin and superconducting qubit readout.
A cryogenic low-voltage, broadband low-noise amplifier(LNA) has been designed for qubit state readout systems. The proposed LNA utilizes passive components for noise cancellation. A tri-coupled transformer is utilized to simultaneously achieve broadband input impedance matching and noise matching. Additionally, it incorporates capacitive feedback and an in-phase transformer to effectively cancel noise. Implemented in 28-nm bulk CMOS technology and verified at 10 K, the LNA achieves a maximum gain of 26.7 dB, a −3-dB bandwidth of 2.2 GHz, a lowest noise temperature (NT) of 25 K, a power consumption of 4.05 mW at 0.6-V supply voltage, and a figure of merit (FoM) of 0.12 dB/mW/ph, which is comparable with the recent works.
This paper presents a cryogenic low-noise amplifier designed for superconducting qubit readout in quantum computing systems. The proposed LNA adopts a three-stage cascaded to achieve a balanced trade-off between gain and noise. Moreover, optimized inter-stage matching is also used. At 300K, the LNA exhibits a bandwidth of 4–8 GHz with a gain ranging from 33 to 35 dB, and a noise figure of 1.5 dB at 6 GHz. At 4K, it delivers over 32 dB gain across 4-8 GHz with noise temperature below 20K (minimum 15K), while power only 12 mW. Additionally, this C-band cryogenic MMIC LNA is designed in a 250 nm GaAs pHEMT process.
This work introduces a broadband cryogenic receiver for scalable multiplexed readout of qubits. The receiver utilizes a double quadrature architecture with amplitude and phase error suppression. The hybrid poly-phase filter (PPF) is applied in the architecture to further reduce the input amplitude and phase errors at the radio frequency (RF) end, enhancing the circuit's overall error vector magnitude (EVM). To address the issue of wide bandwidth (BW) for qubit expansion, a low noise amplifier (LNA) with broadband input and noise matching and an improved four-input intermediate frequency amplifier (IF-AMP) with a resistance feedback structure are proposed, achieving a broadband gain response with high flatness. The chip has been designed in standard 55 nm CMOS technology. The LNA achieves a measured power gain of 27.4 dB at 5 GHz with a -3 dB BW of 5.2 GHz at 6 K. Across the entire band of interest, the measured noise figure (NF) deviates by just 0.15 dB from the minimum noise figure (NFmin) and less than 2 dB at 300K, while the measured cryogenic NF falls within the range of 0.79-1 dB. The LNA consumes only 5.5 mW from a 1.2 V supply. Simulation results of the designed receiver indicate that it delivers an average gain of 49.5 dB with a -3 dB BW of 2.4 GHz and an image rejection ratio (IRR) exceeding 40 dB at 300 K.
Large-scale superconducting quantum computers require massive numbers of high-performance cryogenic low-noise amplifiers (cryo-LNAs) for qubit readout. Here we presented a C-band monolithic microwave integrated circuit (MMIC) cryo-LNA for this purpose. This cryo-LNA is based on a 150 nm gallium arsenide (GaAs) pseudomorphic high electron mobility transistor (pHEMT) process and implemented with a three-stage cascaded architecture, where the first stage adopts careful impedance matching to optimize the noise and return loss. The integration of negative feedback loops adopted in the second and third stages enhances the overall stability. Moreover, the pHEMT self-bias and current multiplexing circuitry structure facilitate the reduction of power consumption and require only a single bias line. Operating at an ambient temperature of 3.6 K and consuming 15 mW, the cryo-LNA demonstrates good performance in the C-band, reaching a minimum noise temperature of 4 K and an average gain of 40 dB. We further benchmarked this cryo-LNA with superconducting qubits, achieving an average single-shot dispersive readout fidelity of 98.3% without assistance from a quantum-limited parametric amplifier. The development of GaAs cryo-LNA diversifies technical support necessary for large-scale quantum applications.
This paper presents a 4–7GHz cryogenic readout integrated circuit (ROIC) implemented in a 65-nm CMOS process for superconducting multi-qubit readout. The proposed ROIC front-end employs a transformer (TF)-based dual-path noise-canceling low-noise amplifier and a TF-based current-bleeding active mixer to enhance gain while suppressing thermal and flicker noise. To realize a wide dynamic range and a large intermediate frequency (IF) bandwidth, a dB-linear broadband (435MHz) variable-gain amplifier with an active-RC feedback topology is employed for multi-qubit sensing. The fabricated ROIC operates at a cryogenic temperature (13K), achieving a maximum gain of 70.4dB and a minimum noise figure of 0.41dB (29K noise temperature) over 435MHz IF bandwidth. The input 1-dB compression point and the input third-order intercept point reach–59.8dBm and–50.4dBm at the maximum gain setting, and–29.8dBm and–20.7dBm at the minimum gain setting, respectively. The ROIC achieves a spurious-free dynamic range of 30.8dB and 50.6dB at maximum and minimum gain settings, respectively, demonstrating competitive performance among reported cryogenic ROICs. The prototype consumes 16.3mW from a 1.2-V supply at 13K with an active area of 1.45 mm2.
This work presents the design and post-layout simulation of a cryogenic SiGe BiCMOS low-noise amplifier (LNA) for superconducting transmon-qubit readout in quantum processors scaling beyond hundreds of qubits. The target specifications are first established and justified by surveying state-of-the-art of cryogenic LNAs and modeling the dispersive qubit readout process. The LNA is implemented with three cascaded stages in common-emitter configuration and employs tuned inductive matching and parallel peaking networks in each stage to optimize noise, gain flatness, and bandwidth while maintaining minimal DC power consumption. The amplifier draws only 1.15 mW from a 0.15 V supply and occupies0.252mm20.252 \text{mm}^{2}0.252mm2. Post-layout simulations confirm input/output S-parameter matching better than−10dB,41−44dB-10 \text{dB}, 41-44 \text{dB}−10dB,41−44dBgain with<3dB<3 \text{dB}<3dBripple,<5K<5 \mathrm{K}<5Knoise temperature across4−9GHz4-9 \text{GHz}4−9GHz, and a worst-case OP1 dB compression point of−19.96.6dBm\mathbf{- 1 9. 9 6. 6 d B m}−19.96.6dBm. A comparative analysis demonstrates that SiGe BiCMOS offers a favorable trade-off between InP HEMT's low noise and CMOS's integration potential for large-scale quantum processors.