Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optical Computing

Optical Error Correction by Adaptive Thresholding

David Kagan, Harry Friedmann

Published Jan 1, 1989• 0 citations
Publisher

Abstract

During the last few years we have suggested1−2 the use of a four-level system irradiated by a bichromatic beam to obtain a tunable optical bistable device. By tunable we mean that the switching threshold can be altered without changing the hardware characteristics, the operating temperature, or the frequencies of the inputs to the device. The basic principle of our suggestion is that by irradiating the non-linear optical material by two beams of appropriately chosen frequencies in an optical cavity, one can act as a signal and the other as tuning control beam. The advantage of the four level system lay in the possibility of using low power control beams which could tune the characteristic optically bistable output curves.

DOI
10.1364/optcomp.1989.tui19

Related papers

Adaptive Optical Logic And Switching Devices

David Kagan, Harry Friedmann

Tunable Optical Bistability, where a low power control beam is used to adapt the hysteresis response and the switching of optically bistable elements, is shown to occur in various systems with a bichromatic input. Some applications of this are suggested for more complex logic gates and for pattern recognition.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Mar 10, 1988•1 citation

Controlled steady-state switching in optical bistability

Andy Brown, Amitabh Joshi, Min Xiao

Optical switching has been achieved between two steady states of optical bistability generated in a system with three-level atoms inside an optical cavity. The optical power switching is controlled by adding short positive (switching up) or negative (switching down) pulses to the input intensity. The coupling laser beam in the three-level atomic system is used to control the threshold value and the width of the hysteresis cycle, which can adjust and optimize the optical switching process.

Applied Physics Letters•Aug 12, 2003•68 citations

Tunable optical bistability of bichromatic fields interacting with four-level systems

D. Kagan, Harry Friedmann

A simple four-level model is used to describe two-band systems such as dyes and semiconductors. The system is irradiated by a bichromatic input in an optical cavity and both fields exhibit optical multistability. The calculations take into account the possibility of noncoherent (electrical) pumping of the system, thus generalizing the model to include semiconductor laser amplifiers. Since both fields are allowed to resonate in the cavity, a low-intensity control beam and/or the noncoherent pumping intensity can 'tune' and adapt the response of the second input. Some applications of this tunability are outlined.>

IEEE Journal of Quantum Electronics•Jun 1, 1989•3 citations

Optimum control beam angle for a biased optical bistable device

Rosie Cush

The control beam intensity required to switch a multibeam, cascadable Fabry–Perot bistable device may be minimised by varying the beam incident angle.

Electronics Letters•Jun 4, 1987•2 citations

Light Level To Electrical Frequency Conversion With Hybrid Optical Bistable Devices

José A. Martín-Pereda, Miguel A. Muriel

A new concept in light level detection. The basis is the use of hybrid optical bistable devices working in oscillatory mode. The obtained instabilities show a correspondence between their frequency and the laser light intensity.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Mar 27, 1985•1 citation

Backpropagating neurons from bichromatic interaction with a three-level system

David Kagan, Harry Friedmann

Optical implementation of a backpropagating neuron by means of a nonlinear Fabry-Perot etalon requires thresholding a forward signal beam while the transmittance of a backpropagating beam is multiplied by the differential of the forward signal. This is achievable by inputting a bichromatic field to a three-level system in an optical cavity. The response characteristics of this device have the added possibility of adaptability of the threshold by the backward probe input intensity.

Applied Optics•May 1, 1989•3 citations
During the last few years we have suggested1−2 the use of a four-level system irradiated by a bichromatic beam to obtain a tunable optical bistable device. By tunable we mean that the switching threshold can be altered without changing the hardware characteristics, the operating temperature, or the frequencies of the inputs to the device. The basic principle of our suggestion is that by irradiating the non-linear optical material by two beams of appropriately chosen frequencies in an optical cavity, one can act as a signal and the other as tuning control beam. The advantage of the four level system lay in the possibility of using low power control beams which could tune the characteristic optically bistable output curves.
A simple four-level model is used to describe two-band systems such as dyes and semiconductors. The system is irradiated by a bichromatic input in an optical cavity and both fields exhibit optical multistability. The calculations take into account the possibility of noncoherent (electrical) pumping of the system, thus generalizing the model to include semiconductor laser amplifiers. Since both fields are allowed to resonate in the cavity, a low-intensity control beam and/or the noncoherent pumping intensity can 'tune' and adapt the response of the second input. Some applications of this tunability are outlined.>