Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

URSI Atlantic Radio Science Conference

A Superconducting Quantum Interference Device Model for the Design and Optimization of Quantum-Limited Microwave Amplifiers in Harmonic Balance Simulators

Alírio Boaventura

Published May 29, 2022• 2 citations
Publisher

Abstract

We present a dc superconducting quantum interference device (dc-SQUID) model for the design and optimization of quantum-limited parametric amplifiers. These devices are critical for superconducting quantum computing and do not currently have comprehensive models that designers can use to simulate their circuits in standard circuit simulators. Our model has been implemented and tested in the Advanced Design Systems (ADS) simulation software and validated against analytical predictions.

DOI
10.23919/at-ap-rasc54737.2022.9814350

Related papers

Optimization of a Low-Tc DC SQUID Amplifier With Tightly Coupled Input Coils

J. Pleikies, O. Usenko, G. Frossati +1 more

We optimized the design and operation of a low-Tc direct current superconducting quantum interference device (dc SQUID) with an integrated coupling coil of 1.5 muH inductance taking into account typical effects observed for similar devices. Numerical simulations were performed on a model including the capacitance of the Josephson junctions, thermal noise of the integrated shunt- and damping- resistors as well as a complex frequency dependent impedance of the SQUID loop originating from the integrated coils. The experimentally and numerically determined characteristics and sensitivity are in good agreement. A minimum additional coupled energy resolution of 700 (h/2p) and 250 (h/2p) was measured at a temperature of 4.2 K and 1.5 K, respectively.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•6 citations

Optimization of dc SQUID linear amplifiers and the quantum noise limit

Claudia D. Tesche

A model for inductively coupled linear amplifier and magnetometer circuits employing superconducting quantum interference devices (dc SQUID’s), which is accurate to all values in the coupling strength, is described. The model explicitly includes the interaction between the input circuit and the dc SQUID. The optimization of the untuned linear amplifier is discussed in detail. The uncertainty principle constraint on the noise temperature of a linear amplifier is shown to place a constraint on the minimum achievable values of the noise figures of an isolated dc SQUID in the quantum noise limit.

Applied Physics Letters•Sep 1, 1982•35 citations

Input impedance of an amplifier based on a dc superconducting quantum interference device

Claude Hilbert, John L. Clarke

The measured input impedance of an amplifier involving a coil tightly coupled to a dc superconducting quantum interference device (SQUID) is found to depend on the current and flux biases of the SQUID. Variations in the input inductance arise from the reflected dynamic inductance of the SQUID, and are in reasonable agreement with the predictions of an analog simulator. Variations in the input resistance, on the other hand, arise from feedback between the output of the SQUID and the input circuit, and are in approximate agreement with the predictions of a simple model.

Applied Physics Letters•Oct 1, 1984•15 citations

Microstrip Superconducting Quantum Interference Devices for Quantum Information Science

De Feo, P Michael

Quantum-limited amplification in the microwave frequency range is of both practical and fundamental importance. The weak signals corresponding to single microwave photons require substantial amplification to resolve. When probing quantum excitations of the electromagnetic field, the substantial noise produced by standard amplifiers dominates the signal, therefore, several averages must be accumulated to achieve even a modest signal-to-noise ratio. Even worse, the back-action on the system due to amplifier noise can hasten the decay of the quantum state. In recent years, low-noise microwave-frequency amplification has been advancing rapidly and one field that would benefit greatly from this is circuit quantum electrodynamics (cQED). The development of circuit quantum electrodynamics---which implements techniques of quantum optics at microwave frequencies---has led to revolutionary progress in the field of quantum information science. cQED employs quantum bits (qubits) and superconducting microwave resonators in place of the atoms and cavities used in quantum optics permitting preparation and control of low energy photon states in macroscopic superconducting circuits at millikelvin temperatures. We have developed a microstrip superconducting quantum interference device (SQUID) amplifier (MSA) to provide the first stage of amplification for these systems. Employing sub-micron Josephson tunnel junctions for enhanced gain, these MSAs operate at microwave frequencies and are optimized to perform with near quantum-limited noise characteristics. Our MSA is utilized as the first stage of amplification to probe the dynamics of a SQUID oscillator. The SQUID oscillator is a flux-tunable microwave resonator formed by a capacitively shunted dc SQUID. Josephson plasma oscillations are induced by pulsed microwave excitations at the resonant frequency of the oscillator. Once pulsed, decaying plasma oscillations are observed in the time domain. By measuring with pulse amplitudes approaching the critical current of the SQUID, it is possible to probe the free evolution of a highly nonlinear oscillator.

•Jan 1, 2012•0 citations

Simulation of a flux-pumped Josephson parametric amplifier with a detailed SQUID model using the harmonic balance method

Kaiyong He, Genting Dai, Qing Yu +4 more

Abstract This work presents an analysis of a flux-pumped Josephson parametric amplifier (JPA) with a detailed superconducting quantum interference device (SQUID) model, using the harmonic balance (HB) method in Keysight’s Advanced Design System. The model is built using the generalized resistively shunted junction model of a Josephson junction and the quantization condition of a SQUID, incorporating the effects of the geometric inductance and parasitic parameters. This approach is used to simulate the behavior of an unmatched lumped element JPA and an impedance-matched JPA, showing the necessity of the detailed SQUID model for the simulation of a broadband JPA by comparison with the results based on a widely used, simplified model. Gain profiles obtained from the approach are consistent with existing experiments in the literature, with reasonable accuracy. Due to the HB method, the simulation is of high efficiency, making it feasible to sweep and optimize parameters. This provides a useful method for the analysis of Josephson parametric amplification and the design of a JPA.

Superconductor Science and Technology•Jan 18, 2023•9 citations

Proposal for a Beat Oscillating Superconducting Quantum Interference Device

Hisao Furukawa, Shinji Tomiyama, Itsuo Hatono +1 more

We describe a new dc-superconducting quantum interference device (SQUID) circuit of the FM type, which has a large coefficient for converting an applied magnetic flux into a frequency of MHz band or a lower band. The circuit consists of a SQUID amplifier composed of two stages, formed by a superconducting weak link and two dc-SQUID elements with nonhysteretic characteristics. In the first stage, the weak link and dc-SQUID elements are connected in parallel and operated by a common bias voltage. Since the respective elements oscillate with high frequencies by the ac Josephson effect, the two frequencies interact with each other, so that, the first stage generates a beat signal of a lower frequency. In the second stage, the other dc-SQUID element with a intrinsic flux gain enhances the beat signal generated during the first stage. A theoretical analysis of the circuit with computer simulation shows that the beat frequency is a periodical function of the magnetic flux, and the SQUID amplifier with two stages can improve the flux sensitivity.

Japanese Journal of Applied Physics•May 1, 1998•0 citations
We present a dc superconducting quantum interference device (dc-SQUID) model for the design and optimization of quantum-limited parametric amplifiers. These devices are critical for superconducting quantum computing and do not currently have comprehensive models that designers can use to simulate their circuits in standard circuit simulators. Our model has been implemented and tested in the Advanced Design Systems (ADS) simulation software and validated against analytical predictions.
We optimized the design and operation of a low-Tc direct current superconducting quantum interference device (dc SQUID) with an integrated coupling coil of 1.5 muH inductance taking into account typical effects observed for similar devices. Numerical simulations were performed on a model including the capacitance of the Josephson junctions, thermal noise of the integrated shunt- and damping- resistors as well as a complex frequency dependent impedance of the SQUID loop originating from the integrated coils. The experimentally and numerically determined characteristics and sensitivity are in good agreement. A minimum additional coupled energy resolution of 700 (h/2p) and 250 (h/2p) was measured at a temperature of 4.2 K and 1.5 K, respectively.
A model for inductively coupled linear amplifier and magnetometer circuits employing superconducting quantum interference devices (dc SQUID’s), which is accurate to all values in the coupling strength, is described. The model explicitly includes the interaction between the input circuit and the dc SQUID. The optimization of the untuned linear amplifier is discussed in detail. The uncertainty principle constraint on the noise temperature of a linear amplifier is shown to place a constraint on the minimum achievable values of the noise figures of an isolated dc SQUID in the quantum noise limit.
The measured input impedance of an amplifier involving a coil tightly coupled to a dc superconducting quantum interference device (SQUID) is found to depend on the current and flux biases of the SQUID. Variations in the input inductance arise from the reflected dynamic inductance of the SQUID, and are in reasonable agreement with the predictions of an analog simulator. Variations in the input resistance, on the other hand, arise from feedback between the output of the SQUID and the input circuit, and are in approximate agreement with the predictions of a simple model.
Quantum-limited amplification in the microwave frequency range is of both practical and fundamental importance. The weak signals corresponding to single microwave photons require substantial amplification to resolve. When probing quantum excitations of the electromagnetic field, the substantial noise produced by standard amplifiers dominates the signal, therefore, several averages must be accumulated to achieve even a modest signal-to-noise ratio. Even worse, the back-action on the system due to amplifier noise can hasten the decay of the quantum state. In recent years, low-noise microwave-frequency amplification has been advancing rapidly and one field that would benefit greatly from this is circuit quantum electrodynamics (cQED). The development of circuit quantum electrodynamics---which implements techniques of quantum optics at microwave frequencies---has led to revolutionary progress in the field of quantum information science. cQED employs quantum bits (qubits) and superconducting microwave resonators in place of the atoms and cavities used in quantum optics permitting preparation and control of low energy photon states in macroscopic superconducting circuits at millikelvin temperatures. We have developed a microstrip superconducting quantum interference device (SQUID) amplifier (MSA) to provide the first stage of amplification for these systems. Employing sub-micron Josephson tunnel junctions for enhanced gain, these MSAs operate at microwave frequencies and are optimized to perform with near quantum-limited noise characteristics. Our MSA is utilized as the first stage of amplification to probe the dynamics of a SQUID oscillator. The SQUID oscillator is a flux-tunable microwave resonator formed by a capacitively shunted dc SQUID. Josephson plasma oscillations are induced by pulsed microwave excitations at the resonant frequency of the oscillator. Once pulsed, decaying plasma oscillations are observed in the time domain. By measuring with pulse amplitudes approaching the critical current of the SQUID, it is possible to probe the free evolution of a highly nonlinear oscillator.
Abstract This work presents an analysis of a flux-pumped Josephson parametric amplifier (JPA) with a detailed superconducting quantum interference device (SQUID) model, using the harmonic balance (HB) method in Keysight’s Advanced Design System. The model is built using the generalized resistively shunted junction model of a Josephson junction and the quantization condition of a SQUID, incorporating the effects of the geometric inductance and parasitic parameters. This approach is used to simulate the behavior of an unmatched lumped element JPA and an impedance-matched JPA, showing the necessity of the detailed SQUID model for the simulation of a broadband JPA by comparison with the results based on a widely used, simplified model. Gain profiles obtained from the approach are consistent with existing experiments in the literature, with reasonable accuracy. Due to the HB method, the simulation is of high efficiency, making it feasible to sweep and optimize parameters. This provides a useful method for the analysis of Josephson parametric amplification and the design of a JPA.
We describe a new dc-superconducting quantum interference device (SQUID) circuit of the FM type, which has a large coefficient for converting an applied magnetic flux into a frequency of MHz band or a lower band. The circuit consists of a SQUID amplifier composed of two stages, formed by a superconducting weak link and two dc-SQUID elements with nonhysteretic characteristics. In the first stage, the weak link and dc-SQUID elements are connected in parallel and operated by a common bias voltage. Since the respective elements oscillate with high frequencies by the ac Josephson effect, the two frequencies interact with each other, so that, the first stage generates a beat signal of a lower frequency. In the second stage, the other dc-SQUID element with a intrinsic flux gain enhances the beat signal generated during the first stage. A theoretical analysis of the circuit with computer simulation shows that the beat frequency is a periodical function of the magnetic flux, and the SQUID amplifier with two stages can improve the flux sensitivity.