Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Microstrip Superconducting Quantum Interference Devices for Quantum Information Science

De Feo, P Michael

Published Jan 1, 2012• 0 citations
OpenAlex

Abstract

Quantum-limited amplification in the microwave frequency range is of both practical and fundamental importance. The weak signals corresponding to single microwave photons require substantial amplification to resolve. When probing quantum excitations of the electromagnetic field, the substantial noise produced by standard amplifiers dominates the signal, therefore, several averages must be accumulated to achieve even a modest signal-to-noise ratio. Even worse, the back-action on the system due to amplifier noise can hasten the decay of the quantum state. In recent years, low-noise microwave-frequency amplification has been advancing rapidly and one field that would benefit greatly from this is circuit quantum electrodynamics (cQED). The development of circuit quantum electrodynamics---which implements techniques of quantum optics at microwave frequencies---has led to revolutionary progress in the field of quantum information science. cQED employs quantum bits (qubits) and superconducting microwave resonators in place of the atoms and cavities used in quantum optics permitting preparation and control of low energy photon states in macroscopic superconducting circuits at millikelvin temperatures. We have developed a microstrip superconducting quantum interference device (SQUID) amplifier (MSA) to provide the first stage of amplification for these systems. Employing sub-micron Josephson tunnel junctions for enhanced gain, these MSAs operate at microwave frequencies and are optimized to perform with near quantum-limited noise characteristics. Our MSA is utilized as the first stage of amplification to probe the dynamics of a SQUID oscillator. The SQUID oscillator is a flux-tunable microwave resonator formed by a capacitively shunted dc SQUID. Josephson plasma oscillations are induced by pulsed microwave excitations at the resonant frequency of the oscillator. Once pulsed, decaying plasma oscillations are observed in the time domain. By measuring with pulse amplitudes approaching the critical current of the SQUID, it is possible to probe the free evolution of a highly nonlinear oscillator.

Related papers

Optimization of superconducting flux qubit readout using near-quantum-limited amplifiers

Jedediah E Johnson

Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.

•Jan 1, 2012•2 citations

Optimization of superconducting flux qubit readout using near-quantum-limited amplifiers - eScholarship

Jedediah E Johnson

Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.

•Jan 1, 2012•0 citations

Quantum noise correlations and amplifiers in mesoscopic systems

Pasi Lähteenmäki

This thesis work deals with a range of superconducting devices operated near the fundamental performance limits set by quantum mechanics along with the nature of quantum vacuum itself when perturbed by such devices. These devices are operated in a dilution refrigerator cooled down to sub-Kelvin temperatures. Low temperature is absolutely essential for quantum behavior of these devices and the minimal inherent noise contribution. Biased, selectively damped superconducting tunnel junction, (also known as the Josephson junction) displaying negative differential resistance, was employed to construct a device capable of amplifying weak microwave signal reflections from it. This device can be operated near the intrinsic precision limits set by the Heisenberg's uncertainty principle. Arrays of Superconducting Quantum Interference Devices (SQUIDs), operated below the critical current, can be used for metamaterial resonators whose resonant frequency can be quickly modulated by magnetic flux. These devices are operated as parametric amplifiers and they are capable of amplifying weak microwave signals near the quantum limit of noise. But more importantly, they are capable of perturbing the vacuum itself, which creates correlated photon pairs seeded by vacuum fluctuations. This effect is known as the dynamical Casimir effect (DCE) and is demonstrated in this thesis work by using power and correlation measurements at microwave frequencies. Furthermore, investigations on the DCE have been extended using a double modulation scheme yielding vacuum-induced coherence and tripartite correlations. Nanocarbon devices have also been studied in this thesis, in particular a wideband low noise nanotube electrometer constructed from a nanotube with proximity induced superconductivity. This device has certain unique benefits when operated in a microwave environment which are discussed in the thesis. Another nanocarbon device, a double quantum dot constructed from graphene and superconducting leads has been used to demonstrate Cooper-pair splitting. This device operates as a tunable source of entangled electrons.

•Jan 1, 2016•0 citations

Microstrip superconducting quantum interference device amplifiers with submicron Josephson junctions: Enhanced gain at gigahertz frequencies

M. P. DeFeo, P. Bhupathi, K. Yu +4 more

We present measurements of an amplifier based on a dc superconducting quantum interference device (SQUID) with submicron Al–AlOx–Al Josephson junctions. The small junction size reduces their self-capacitance and allows for the use of relatively large resistive shunts while maintaining nonhysteretic operation. This leads to an enhancement of the SQUID transfer function compared to SQUIDs with micron-scale junctions. The device layout is modified from that of a conventional SQUID to allow for coupling signals into the amplifier with a substantial mutual inductance for a relatively short microstrip coil. Measurements at 310 mK exhibit gain of 32 dB at 1.55 GHz.

arXiv:1008.1036•Applied Physics Letters•Aug 30, 2010•12 citations

Broadband SQUID amplifiers for photonic applications

Vladimir Polushkin, D. Glowacka, R. Hart +1 more

The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•1 citation

The Josephson parametric oscillator - From microscopic studies to single-shot qubit readout

Philip Krantz

Circuit quantum electrodynamics (cQED) is a prominent platform for quantum information processing, in which microwave photons are confined into resonant cavities coupled to superconducting quantum bits (qubits). The large effective dipole moment of the qubit, in combination with the high energy density of the quasi 1-D resonator allow these systems to enter the so-called strong coupling regime. The quantum state of the qubit can then be assessed by probing the frequency of the resonator, protecting the qubit from otherwise losing its energy to the environment. However, eventhough this so-called dispersive readout technique has proven useful, it is often in itself insufficient to render single-shot readout performance | one of the crucial tasks required for realizing a quantum computer. This thesis describes the demonstration of a single-shot readout technique forsuperconducting quantum bits, based on coupling the qubit to a frequency-tunable resonator. The backbone of our device is a 5 GHz quarter-wavelength coplanar waveguide resonator, terminated at one end by a non-linear inductance provided by a superconducting quantum interference device (SQUID). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using an on-chip transmission line. The modulation occurs on a timescale much faster than the photon loss out of the resonator and if the pump strength exceeds a threshold value set by the damping rate of the resonator, an intense photon field will build up inside the resonator | known as "parametric oscillations". By heterodyne detection of the output signal from the Josephson parametric oscillator (JPO), we first extracted two leading nonlinear effects of the system (dominating in different limits of applied magnetic flux). Next, we couple a qubit to the JPO and demonstrate that we can encode its quantum state onto the strong output field of the parametric oscillator (or lack thereof), rendering a signal-to-noise ratio sufficient for single-shot state detection and therefore also obviating a quantum limited parametric amplifier. The thesis also contains results from microscopic studies of the Josephson junctions, which we use to provide the necessary nonlinearities in the above mentioned devices. In particular, we show how the microstructure of the barrier layer and its atomic composition can be used to infer important electrical properties of the junctions. This knowledge allows us to better tailor the properties of Josephson-based devices.

•Jan 1, 2016•4 citations
Quantum-limited amplification in the microwave frequency range is of both practical and fundamental importance. The weak signals corresponding to single microwave photons require substantial amplification to resolve. When probing quantum excitations of the electromagnetic field, the substantial noise produced by standard amplifiers dominates the signal, therefore, several averages must be accumulated to achieve even a modest signal-to-noise ratio. Even worse, the back-action on the system due to amplifier noise can hasten the decay of the quantum state. In recent years, low-noise microwave-frequency amplification has been advancing rapidly and one field that would benefit greatly from this is circuit quantum electrodynamics (cQED). The development of circuit quantum electrodynamics---which implements techniques of quantum optics at microwave frequencies---has led to revolutionary progress in the field of quantum information science. cQED employs quantum bits (qubits) and superconducting microwave resonators in place of the atoms and cavities used in quantum optics permitting preparation and control of low energy photon states in macroscopic superconducting circuits at millikelvin temperatures. We have developed a microstrip superconducting quantum interference device (SQUID) amplifier (MSA) to provide the first stage of amplification for these systems. Employing sub-micron Josephson tunnel junctions for enhanced gain, these MSAs operate at microwave frequencies and are optimized to perform with near quantum-limited noise characteristics. Our MSA is utilized as the first stage of amplification to probe the dynamics of a SQUID oscillator. The SQUID oscillator is a flux-tunable microwave resonator formed by a capacitively shunted dc SQUID. Josephson plasma oscillations are induced by pulsed microwave excitations at the resonant frequency of the oscillator. Once pulsed, decaying plasma oscillations are observed in the time domain. By measuring with pulse amplitudes approaching the critical current of the SQUID, it is possible to probe the free evolution of a highly nonlinear oscillator.
Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.
Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.
This thesis work deals with a range of superconducting devices operated near the fundamental performance limits set by quantum mechanics along with the nature of quantum vacuum itself when perturbed by such devices. These devices are operated in a dilution refrigerator cooled down to sub-Kelvin temperatures. Low temperature is absolutely essential for quantum behavior of these devices and the minimal inherent noise contribution. Biased, selectively damped superconducting tunnel junction, (also known as the Josephson junction) displaying negative differential resistance, was employed to construct a device capable of amplifying weak microwave signal reflections from it. This device can be operated near the intrinsic precision limits set by the Heisenberg's uncertainty principle. Arrays of Superconducting Quantum Interference Devices (SQUIDs), operated below the critical current, can be used for metamaterial resonators whose resonant frequency can be quickly modulated by magnetic flux. These devices are operated as parametric amplifiers and they are capable of amplifying weak microwave signals near the quantum limit of noise. But more importantly, they are capable of perturbing the vacuum itself, which creates correlated photon pairs seeded by vacuum fluctuations. This effect is known as the dynamical Casimir effect (DCE) and is demonstrated in this thesis work by using power and correlation measurements at microwave frequencies. Furthermore, investigations on the DCE have been extended using a double modulation scheme yielding vacuum-induced coherence and tripartite correlations. Nanocarbon devices have also been studied in this thesis, in particular a wideband low noise nanotube electrometer constructed from a nanotube with proximity induced superconductivity. This device has certain unique benefits when operated in a microwave environment which are discussed in the thesis. Another nanocarbon device, a double quantum dot constructed from graphene and superconducting leads has been used to demonstrate Cooper-pair splitting. This device operates as a tunable source of entangled electrons.
We present measurements of an amplifier based on a dc superconducting quantum interference device (SQUID) with submicron Al–AlOx–Al Josephson junctions. The small junction size reduces their self-capacitance and allows for the use of relatively large resistive shunts while maintaining nonhysteretic operation. This leads to an enhancement of the SQUID transfer function compared to SQUIDs with micron-scale junctions. The device layout is modified from that of a conventional SQUID to allow for coupling signals into the amplifier with a substantial mutual inductance for a relatively short microstrip coil. Measurements at 310 mK exhibit gain of 32 dB at 1.55 GHz.
The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.
Circuit quantum electrodynamics (cQED) is a prominent platform for quantum information processing, in which microwave photons are confined into resonant cavities coupled to superconducting quantum bits (qubits). The large effective dipole moment of the qubit, in combination with the high energy density of the quasi 1-D resonator allow these systems to enter the so-called strong coupling regime. The quantum state of the qubit can then be assessed by probing the frequency of the resonator, protecting the qubit from otherwise losing its energy to the environment. However, eventhough this so-called dispersive readout technique has proven useful, it is often in itself insufficient to render single-shot readout performance | one of the crucial tasks required for realizing a quantum computer. This thesis describes the demonstration of a single-shot readout technique forsuperconducting quantum bits, based on coupling the qubit to a frequency-tunable resonator. The backbone of our device is a 5 GHz quarter-wavelength coplanar waveguide resonator, terminated at one end by a non-linear inductance provided by a superconducting quantum interference device (SQUID). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using an on-chip transmission line. The modulation occurs on a timescale much faster than the photon loss out of the resonator and if the pump strength exceeds a threshold value set by the damping rate of the resonator, an intense photon field will build up inside the resonator | known as "parametric oscillations". By heterodyne detection of the output signal from the Josephson parametric oscillator (JPO), we first extracted two leading nonlinear effects of the system (dominating in different limits of applied magnetic flux). Next, we couple a qubit to the JPO and demonstrate that we can encode its quantum state onto the strong output field of the parametric oscillator (or lack thereof), rendering a signal-to-noise ratio sufficient for single-shot state detection and therefore also obviating a quantum limited parametric amplifier. The thesis also contains results from microscopic studies of the Josephson junctions, which we use to provide the necessary nonlinearities in the above mentioned devices. In particular, we show how the microstructure of the barrier layer and its atomic composition can be used to infer important electrical properties of the junctions. This knowledge allows us to better tailor the properties of Josephson-based devices.