Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Optimization of dc SQUID linear amplifiers and the quantum noise limit

Claudia D. Tesche

Published Sep 1, 1982• 35 citations
Publisher

Abstract

A model for inductively coupled linear amplifier and magnetometer circuits employing superconducting quantum interference devices (dc SQUID’s), which is accurate to all values in the coupling strength, is described. The model explicitly includes the interaction between the input circuit and the dc SQUID. The optimization of the untuned linear amplifier is discussed in detail. The uncertainty principle constraint on the noise temperature of a linear amplifier is shown to place a constraint on the minimum achievable values of the noise figures of an isolated dc SQUID in the quantum noise limit.

DOI
10.1063/1.93542

Related papers

Analysis of strong inductive coupling on SQUID systems

Claudia D. Tesche

A technique for the analysis of complex superconducting circuits containing one or more current biased inductively coupled Josephson junction interferometers is described. The equations of motion for the system are shown to separate into a set of non-linear junction equations relating the voltage drops across the junctions to the currents passing through the junctions, and a set of linear equations expressing the quantization of the fluxoid around the superconducting loops and the corresponding linear circuit equations for the normal loops. In many cases, the linear equations can be integrated, resulting in an effective elimination of the normal circuit loops from the problem. The circuit is thus reduced to that of an equivalent set of coupled SQUIDs whose device parameters are a function of the original circuit parameters and the inductive coupling strengths. The dc SQUID tuned linear amplifier is analyzed to display the method. As a result of this analysis, the optimal noise temperature of a tuned SQUID amplifier is derived as a function of the current and voltage noise spectral densities, Svand Sj, and forward transfer function, Vφ. The results obtained demonstrate that the behavior of the SQUID cannot be isolated from that of the rest of the circuit in the manner assumed in previous analyses. The existence of a quantum noise limit on the noise temperature of any phase preserving linear amplifier is used to infer that the noise figures must satisfy the constraint[(S_{v}/2LV_{\phi}^{2})(LS_{j}/2)-S_{vj}^{2}]^{1/2}>\hbarThe behavior of several simple circuits containing a pair of inductively coupled current biased interferometers is discussed to display the extension of the method to circuits containing more than one interferometer.

IEEE Transactions on Magnetics•May 1, 1983•12 citations

Optimization of a Low-Tc DC SQUID Amplifier With Tightly Coupled Input Coils

J. Pleikies, O. Usenko, G. Frossati +1 more

We optimized the design and operation of a low-Tc direct current superconducting quantum interference device (dc SQUID) with an integrated coupling coil of 1.5 muH inductance taking into account typical effects observed for similar devices. Numerical simulations were performed on a model including the capacitance of the Josephson junctions, thermal noise of the integrated shunt- and damping- resistors as well as a complex frequency dependent impedance of the SQUID loop originating from the integrated coils. The experimentally and numerically determined characteristics and sensitivity are in good agreement. A minimum additional coupled energy resolution of 700 (h/2p) and 250 (h/2p) was measured at a temperature of 4.2 K and 1.5 K, respectively.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•6 citations

Quantum noise theory for the dc SQUID

R. H. Koch, Dale J. Van Harlingen, John L. Clarke

The noise temperature of a dc superconducting quantum interference device (SQUID) coupled to a tuned input circuit is computed using the complete quantum expression for the equilibrium noise in the shunt resistance of each junction. At T = 0, where the noise reduces to zero-point fluctuations, the noise temperature for an optimized system is hn/kB ln2, where n is the signal frequency. The computation is extended to nonzero temperatures, and it is shown that a SQUID operated at 1K can approach the quantum limit.

Applied Physics Letters•Mar 1, 1981•92 citations

A coupled DC SQUID with low 1/f noise

Heikki Seppä, M. Kiviranta, Alexandre Satrapinski +3 more

A low-noise coupled DC superconducting quantum interference device (SQUID) especially optimized for low frequency is discussed. Using large Josephson junctions and a low loop inductance the contribution of the critical current fluctuation to 1/f noise can be minimized. To minimize the inductance the Josephson junctions are placed in the center of the washer close to the SQUID loop. A scaled-up copper model of the SQUID and the signal coil is used to analyze the impedance of the SQUID loop affected by the signal coil. An equivalent circuit model describing the effective inductance of the SQUID loop as a function of the frequency is used to design appropriate damping of the resonances. The DC SQUID characteristics are smooth and the noise performance of the SQUID does not markedly suffer from resonances. The contribution of the 1/f noise at 1 Hz is found to be about 5*10/sup -7/ Phi /sub 0// square root Hz.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•25 citations

Optimization of input impedance and mechanism of noise suppression in a DC SQUID RF amplifier

Michael A. Tarasov, Z. G. Ivanov

The optimal input impedance and noise of a DC SQUID RF amplifier at frequencies of the order of 1 GHz with a resonant input matching circuit have been studied analytically, numerically, and experimentally. A model for noise temperature and power gain has been developed for the practical resonant input tank circuit. A new effect of the output noise increasing or decreasing with changing the sign of voltage-to-flux transfer coefficient has been observed experimentally and explained analytically. The different values of noise temperature for the opposite dV/d/spl Phi/ values have been interpreted using a model with partially correlated current and voltage noise sources. The equivalent layout for optimal input matching of a SQUID amplifier comprising series and parallel resonant circuits has been presented. Using such a matching circuit and SIS junction as a signal source the SQUID amplifier noise temperature about 1 K has been measured at 1.1 GHz.

IEEE Transactions on Applied Superconductivity•Jun 1, 1996•3 citations

Strongly coupled, low noise dc-SQUID amplifiers

J. Pleikies

The dc Superconducting Quantum Interference Device (dc-SQUID) is one of the most sensitive magnetic field sensors available. In this thesis we concentrate on its application as an amplifier. In this configuration, an input circuit of interest can be connected by means of a coupling coil. The intended application of our developed low-Tc SQUID amplifiers is the readout of the first spherical gravitational wave antenna MiniGRAIL. Using small-signal analysis as well as numerical simulations, we study the achievable signal-to-noise ratio of such sensors in practical measurements. Published theories and studies could be extended. Some interesting points treated are the influence of the often used negative feedback (flux-locked loop), an altered input impedance of the SQUID amplifier and the influence of back-action noise, which directly affects the object of interest. The altered operation of the SQUID due to the presence of the input circuit is studied in numerical experiments. Another important issue, the influence of integrated input coils on the dynamics of SQUIDs, is investigated theoretically and experimentally. The performance of our developed sensors is compared to numerical simulations on detailed models. The results give insights into the behavior, design and usage of dc-SQUIDs with integrated coils. For a SQUID with input inductances of 1.5 μH we reached a good coupled energy sensitivity of about 170 ¯h in a dilution refrigerator. Furthermore, we investigated the hot-electron effect. This effect typically limits the sensitivity of superconducting electronics at sub-Kelvin bath temperatures due to a weakened electron-phonon coupling. We performed heating experiments on thin-film resistors which are similar to the shunt resistors of the Josephson junctions used in our sensors. The suppression of the hot-electron effect via electronic thermal transport to attached cooling fins is investigated both experimentally, theoretically and numerically. The numerical technique turns out to be a useful tool for the thermal design of superconducting electronics.

•Apr 1, 2009•0 citations
A model for inductively coupled linear amplifier and magnetometer circuits employing superconducting quantum interference devices (dc SQUID’s), which is accurate to all values in the coupling strength, is described. The model explicitly includes the interaction between the input circuit and the dc SQUID. The optimization of the untuned linear amplifier is discussed in detail. The uncertainty principle constraint on the noise temperature of a linear amplifier is shown to place a constraint on the minimum achievable values of the noise figures of an isolated dc SQUID in the quantum noise limit.
A technique for the analysis of complex superconducting circuits containing one or more current biased inductively coupled Josephson junction interferometers is described. The equations of motion for the system are shown to separate into a set of non-linear junction equations relating the voltage drops across the junctions to the currents passing through the junctions, and a set of linear equations expressing the quantization of the fluxoid around the superconducting loops and the corresponding linear circuit equations for the normal loops. In many cases, the linear equations can be integrated, resulting in an effective elimination of the normal circuit loops from the problem. The circuit is thus reduced to that of an equivalent set of coupled SQUIDs whose device parameters are a function of the original circuit parameters and the inductive coupling strengths. The dc SQUID tuned linear amplifier is analyzed to display the method. As a result of this analysis, the optimal noise temperature of a tuned SQUID amplifier is derived as a function of the current and voltage noise spectral densities, Svand Sj, and forward transfer function, Vφ. The results obtained demonstrate that the behavior of the SQUID cannot be isolated from that of the rest of the circuit in the manner assumed in previous analyses. The existence of a quantum noise limit on the noise temperature of any phase preserving linear amplifier is used to infer that the noise figures must satisfy the constraint[(S_{v}/2LV_{\phi}^{2})(LS_{j}/2)-S_{vj}^{2}]^{1/2}>\hbarThe behavior of several simple circuits containing a pair of inductively coupled current biased interferometers is discussed to display the extension of the method to circuits containing more than one interferometer.
We optimized the design and operation of a low-Tc direct current superconducting quantum interference device (dc SQUID) with an integrated coupling coil of 1.5 muH inductance taking into account typical effects observed for similar devices. Numerical simulations were performed on a model including the capacitance of the Josephson junctions, thermal noise of the integrated shunt- and damping- resistors as well as a complex frequency dependent impedance of the SQUID loop originating from the integrated coils. The experimentally and numerically determined characteristics and sensitivity are in good agreement. A minimum additional coupled energy resolution of 700 (h/2p) and 250 (h/2p) was measured at a temperature of 4.2 K and 1.5 K, respectively.
The noise temperature of a dc superconducting quantum interference device (SQUID) coupled to a tuned input circuit is computed using the complete quantum expression for the equilibrium noise in the shunt resistance of each junction. At T = 0, where the noise reduces to zero-point fluctuations, the noise temperature for an optimized system is hn/kB ln2, where n is the signal frequency. The computation is extended to nonzero temperatures, and it is shown that a SQUID operated at 1K can approach the quantum limit.
A low-noise coupled DC superconducting quantum interference device (SQUID) especially optimized for low frequency is discussed. Using large Josephson junctions and a low loop inductance the contribution of the critical current fluctuation to 1/f noise can be minimized. To minimize the inductance the Josephson junctions are placed in the center of the washer close to the SQUID loop. A scaled-up copper model of the SQUID and the signal coil is used to analyze the impedance of the SQUID loop affected by the signal coil. An equivalent circuit model describing the effective inductance of the SQUID loop as a function of the frequency is used to design appropriate damping of the resonances. The DC SQUID characteristics are smooth and the noise performance of the SQUID does not markedly suffer from resonances. The contribution of the 1/f noise at 1 Hz is found to be about 5*10/sup -7/ Phi /sub 0// square root Hz.>
The optimal input impedance and noise of a DC SQUID RF amplifier at frequencies of the order of 1 GHz with a resonant input matching circuit have been studied analytically, numerically, and experimentally. A model for noise temperature and power gain has been developed for the practical resonant input tank circuit. A new effect of the output noise increasing or decreasing with changing the sign of voltage-to-flux transfer coefficient has been observed experimentally and explained analytically. The different values of noise temperature for the opposite dV/d/spl Phi/ values have been interpreted using a model with partially correlated current and voltage noise sources. The equivalent layout for optimal input matching of a SQUID amplifier comprising series and parallel resonant circuits has been presented. Using such a matching circuit and SIS junction as a signal source the SQUID amplifier noise temperature about 1 K has been measured at 1.1 GHz.
The dc Superconducting Quantum Interference Device (dc-SQUID) is one of the most sensitive magnetic field sensors available. In this thesis we concentrate on its application as an amplifier. In this configuration, an input circuit of interest can be connected by means of a coupling coil. The intended application of our developed low-Tc SQUID amplifiers is the readout of the first spherical gravitational wave antenna MiniGRAIL. Using small-signal analysis as well as numerical simulations, we study the achievable signal-to-noise ratio of such sensors in practical measurements. Published theories and studies could be extended. Some interesting points treated are the influence of the often used negative feedback (flux-locked loop), an altered input impedance of the SQUID amplifier and the influence of back-action noise, which directly affects the object of interest. The altered operation of the SQUID due to the presence of the input circuit is studied in numerical experiments. Another important issue, the influence of integrated input coils on the dynamics of SQUIDs, is investigated theoretically and experimentally. The performance of our developed sensors is compared to numerical simulations on detailed models. The results give insights into the behavior, design and usage of dc-SQUIDs with integrated coils. For a SQUID with input inductances of 1.5 μH we reached a good coupled energy sensitivity of about 170 ¯h in a dilution refrigerator. Furthermore, we investigated the hot-electron effect. This effect typically limits the sensitivity of superconducting electronics at sub-Kelvin bath temperatures due to a weakened electron-phonon coupling. We performed heating experiments on thin-film resistors which are similar to the shunt resistors of the Josephson junctions used in our sensors. The suppression of the hot-electron effect via electronic thermal transport to attached cooling fins is investigated both experimentally, theoretically and numerically. The numerical technique turns out to be a useful tool for the thermal design of superconducting electronics.