Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Wiley eBooks

Two‐Stage and Double Relaxation Oscillation Readout Schemes

Yi Zhang, Hui Dong, Hans-Joachim Krause, Guofeng Zhang, Xiaoming Xie

Published May 29, 2020• 0 citations
Publisher

Abstract

This chapter introduces two DC Superconducting QUantum Interference Device (SQUID) readout schemes, i.e. a two-stage scheme and a double relaxation oscillation (D-ROS), suitable for SQUID intrinsic noise observation. The two-stage readout scheme consists of a voltage-biased sensing SQUID and an ammeter with the reading SQUID. Intuitively, SQUIDs with two junctions maintain hysteresis, and their I–V characteristics should contain information on the applied flux. D-ROS, originally called balanced ROS, consisting of two hysteretic DC SQUIDs in series, was developed to increase the transfer coefficient. In the original work, the signal flux was applied to both SQUIDs; i.e. the roles of the two SQUIDs, where one is reading and the other is sensing, can be exchanged. In contrast to balanced ROS, the functions of the two SQUIDs are well defined in D-ROS; i.e. one is the sensing SQUID, and the other is the reading SQUID, similar to two-stage scheme.

DOI
10.1002/9783527816514.ch11

Related papers

Introduction

Yi Zhang, Hui Dong, Hans‐Joachim Krause +2 more

According to the type of superconducting material used, Superconducting QUantum Interference Devices (SQUID) can be divided into two groups: the low-temperature superconducting and the high-temperature superconducting SQUID. Josephson junction (JJ) is the key element of SQUIDs. JJs are analyzed with the resistively and capacitively shunted junction (RCSJ) model, thus introducing two important parameters: the Stewart–McCumber parameter and the thermal rounding parameter. For readout electronics, the DC SQUID is regarded as dynamic resistance Rd modulated by the flux threading into the SQUID loop. In the case of a direct readout scheme where the SQUID directly connects to a preamplifier, the electronics noise is usually much larger than the SQUID intrinsic noise. The techniques of additional positive feedback, bias current feedback, and noise cancellation are categorized and discussed. This chapter introduces two special DC SQUID readout schemes, the two-stage scheme and the double relaxation oscillation (DROS) scheme.

Wiley eBooks•May 29, 2020•0 citations

Second generation dc-SQUID sensors: relaxation oscillation SQUIDS (ROS) with frequency readout and double relaxation oscillation SQUIDS (DROS) with voltage readout

Derk Jan Adelerhof, Michiel van Duuren, Jaap Flokstra +1 more

Relaxation Oscillation SQUIDs (ROSs) based on 4x4 micrometers 2 Nb/AlOx Josephson tunnel junctions have been fabricated and characterized. A ROS consists of a hysteretic dc SQUID shunted by an inductor L and a resistor R in series to induce the relaxation oscillations. The values of L range from 20 nH up to about 300 nH, whereas the time constant L/R are between 8 and 45 ns. Frequency-flux characteristics have been recorded with the help of a spectrum analyzer, directly connected to the ROS. The relaxation frequencies range from 5 to 180 MHz. The experimental characteristics can be explained very well with a simple model describing the oscillation cycle. The effect of the self-induced magnetic field due to a magnetic coupling between the dc SQUID and the shunt circuit has been studied in detail. The sensitivity of ROSs and DROSs (Double Relaxation Oscillation SQUIDs) improves with increasing relaxation frequency. In (D)ROSs based on unshunted, hysteretic tunnel junction dc SQUIDs, the maximum relaxation frequency and the sensitivity are limited by LC resonances due to the SQUID capacitance and the shunt inductance. It is shown that the relaxation frequency can be increased up to frequencies of the order of 1 GHz if an extra resistor is integrated to damp these resonances. The optimum value of the damping resistor can be obtained from the ROS parameters. For stable operation of a (D)ROS, the shunt resistance should not be too large. The optimum value of this resistance can be calculated from the effective McCumber parameter and the bias current. Theoretically, the sensitivity of a ROS with a SQUID capacitance of 1 pF, a SQUID inductance of 20 pH and a relaxation frequency of 1 GHz equals about 5h, where h is Planck's constant. In a DROS with voltage readout based on similar SQUIDs, the theoretical sensitivity at a relaxation frequency of 1 GHz is 17h, with an estimated flux-to-voltage transfer coefficient of 5 mV/(phi) 0.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jul 2, 1994•9 citations

Low-noise SQUIDs with large transfer - two stage SQUIDs based on DROSs

M. Podt, Jakob Flokstra, Horst Rogalla

We have realized a two-stage integrated superconducting quantum interference device (SQUID) system with a closed loop bandwidth of 2.5 MHz, operated in a direct voltage readout mode. The corresponding flux slew rate was 1.3×105 Φ0/s and the measured white flux noise was 1.3 μΦ0/√Hz at 4.2 K. The system is based on a conventional dc SQUID with a double relaxation oscillation SQUID (DROS) as the second stage. Because of the large flux-to-voltage transfer, the sensitivity of the system is completely determined by the sensor SQUID and not by the DROS or the room-temperature preamplifier. Decreasing the Josephson junction area enables a further improvement of the sensitivity of the two-stage SQUID systems.

•Aug 26, 2001•0 citations

Continuous feedback operation of a two-stage dc SQUID system

Insik Jin, F. C. Wellstood

We report on the continuous feedback operation of a two-stage dc Superconducting Quantum Interference Device (SQUID) system in which one SQUID works as a low-noise preamplifier to read out a second low-noise sensor SQUID. We first flux-locked the readout SQUID and measured the characteristics of the sensor SQUID, including its current-voltage characteristics, current-flux characteristics, and noise spectrum. We then investigated how the two SQUIDs could work together by simultaneously flux-locking both the sensor and the readout SQUIDs. With this two-SQUID flux-locking scheme, we recovered the noise spectrum of the sensor SQUID to within 4%. We discuss how to understand and optimize the two-stage SQUID feedback system.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•3 citations

A Practical Two-Stage SQUID Readout Circuit Improved With Proportional Feedback Schemes

Yongliang Wang, Guofeng Zhang, Shulin Zhang +4 more

Nonlinearity with multiple working points limits the practical applications of a two-stage superconducting quantum interference device (SQUID) readout circuit, which is promising for low-noise performance. To solve this problem, we proposed a simple two-stage SQUID readout circuit with two conventional dc SQUIDs improved with proportional feedback schemes, where transfer coefficient of the first-stage SQUID circuit is enhanced by additional positive feedback circuit; transfer characteristics of the second-stage SQUID circuit are linearized by an additional negative feedback circuit. Two proportional feedback schemes are cooperated together based on matching conditions to achieve both noise suppression and working point matching. Working principles were verified in experiment results. The overall transfer characteristics achieved have only one working point and are simply adjusted according to the voltage swing of an amplifier. Transfer coefficient of the first-stage SQUID circuit was raised up to 10 (20 dB), and the total flux noise of two-stage SQUID readout circuit was reduced below 1 μΦ0/√Hz, where Φ0= 2.07×10-15Wb. Our two-stage SQUID readout circuit is easy-to-operate and suited for high-performance practical SQUID systems.

IEEE Transactions on Applied Superconductivity•Jan 29, 2020•2 citations

Two-stage amplifier based on a double relaxation oscillation superconducting quantum interference device

M. Podt, Michiel J. van Duuren, A.W. Hamster +2 more

A low-noise single-chip two-stage superconducting quantum interference device (SQUID) system with a double relaxation oscillation SQUID as the second stage has been realized. The system was operated in a direct voltage readout mode, with a closed loop bandwidth up to 1 MHz. Operated at 4.2 K, the white flux noise measured in flux locked loop was 1.3 μΦ0/√Hz, corresponding to an energy sensitivity of ε≈27h. Owing to the large flux-to-voltage transfer of up to 3.6 mV/Φ0, the room-temperature preamplifier noise did not dominate the overall flux noise.

Applied Physics Letters•Oct 11, 1999•25 citations
This chapter introduces two DC Superconducting QUantum Interference Device (SQUID) readout schemes, i.e. a two-stage scheme and a double relaxation oscillation (D-ROS), suitable for SQUID intrinsic noise observation. The two-stage readout scheme consists of a voltage-biased sensing SQUID and an ammeter with the reading SQUID. Intuitively, SQUIDs with two junctions maintain hysteresis, and their I–V characteristics should contain information on the applied flux. D-ROS, originally called balanced ROS, consisting of two hysteretic DC SQUIDs in series, was developed to increase the transfer coefficient. In the original work, the signal flux was applied to both SQUIDs; i.e. the roles of the two SQUIDs, where one is reading and the other is sensing, can be exchanged. In contrast to balanced ROS, the functions of the two SQUIDs are well defined in D-ROS; i.e. one is the sensing SQUID, and the other is the reading SQUID, similar to two-stage scheme.
According to the type of superconducting material used, Superconducting QUantum Interference Devices (SQUID) can be divided into two groups: the low-temperature superconducting and the high-temperature superconducting SQUID. Josephson junction (JJ) is the key element of SQUIDs. JJs are analyzed with the resistively and capacitively shunted junction (RCSJ) model, thus introducing two important parameters: the Stewart–McCumber parameter and the thermal rounding parameter. For readout electronics, the DC SQUID is regarded as dynamic resistance Rd modulated by the flux threading into the SQUID loop. In the case of a direct readout scheme where the SQUID directly connects to a preamplifier, the electronics noise is usually much larger than the SQUID intrinsic noise. The techniques of additional positive feedback, bias current feedback, and noise cancellation are categorized and discussed. This chapter introduces two special DC SQUID readout schemes, the two-stage scheme and the double relaxation oscillation (DROS) scheme.
Relaxation Oscillation SQUIDs (ROSs) based on 4x4 micrometers 2 Nb/AlOx Josephson tunnel junctions have been fabricated and characterized. A ROS consists of a hysteretic dc SQUID shunted by an inductor L and a resistor R in series to induce the relaxation oscillations. The values of L range from 20 nH up to about 300 nH, whereas the time constant L/R are between 8 and 45 ns. Frequency-flux characteristics have been recorded with the help of a spectrum analyzer, directly connected to the ROS. The relaxation frequencies range from 5 to 180 MHz. The experimental characteristics can be explained very well with a simple model describing the oscillation cycle. The effect of the self-induced magnetic field due to a magnetic coupling between the dc SQUID and the shunt circuit has been studied in detail. The sensitivity of ROSs and DROSs (Double Relaxation Oscillation SQUIDs) improves with increasing relaxation frequency. In (D)ROSs based on unshunted, hysteretic tunnel junction dc SQUIDs, the maximum relaxation frequency and the sensitivity are limited by LC resonances due to the SQUID capacitance and the shunt inductance. It is shown that the relaxation frequency can be increased up to frequencies of the order of 1 GHz if an extra resistor is integrated to damp these resonances. The optimum value of the damping resistor can be obtained from the ROS parameters. For stable operation of a (D)ROS, the shunt resistance should not be too large. The optimum value of this resistance can be calculated from the effective McCumber parameter and the bias current. Theoretically, the sensitivity of a ROS with a SQUID capacitance of 1 pF, a SQUID inductance of 20 pH and a relaxation frequency of 1 GHz equals about 5h, where h is Planck's constant. In a DROS with voltage readout based on similar SQUIDs, the theoretical sensitivity at a relaxation frequency of 1 GHz is 17h, with an estimated flux-to-voltage transfer coefficient of 5 mV/(phi) 0.
We have realized a two-stage integrated superconducting quantum interference device (SQUID) system with a closed loop bandwidth of 2.5 MHz, operated in a direct voltage readout mode. The corresponding flux slew rate was 1.3×105 Φ0/s and the measured white flux noise was 1.3 μΦ0/√Hz at 4.2 K. The system is based on a conventional dc SQUID with a double relaxation oscillation SQUID (DROS) as the second stage. Because of the large flux-to-voltage transfer, the sensitivity of the system is completely determined by the sensor SQUID and not by the DROS or the room-temperature preamplifier. Decreasing the Josephson junction area enables a further improvement of the sensitivity of the two-stage SQUID systems.
We report on the continuous feedback operation of a two-stage dc Superconducting Quantum Interference Device (SQUID) system in which one SQUID works as a low-noise preamplifier to read out a second low-noise sensor SQUID. We first flux-locked the readout SQUID and measured the characteristics of the sensor SQUID, including its current-voltage characteristics, current-flux characteristics, and noise spectrum. We then investigated how the two SQUIDs could work together by simultaneously flux-locking both the sensor and the readout SQUIDs. With this two-SQUID flux-locking scheme, we recovered the noise spectrum of the sensor SQUID to within 4%. We discuss how to understand and optimize the two-stage SQUID feedback system.
Nonlinearity with multiple working points limits the practical applications of a two-stage superconducting quantum interference device (SQUID) readout circuit, which is promising for low-noise performance. To solve this problem, we proposed a simple two-stage SQUID readout circuit with two conventional dc SQUIDs improved with proportional feedback schemes, where transfer coefficient of the first-stage SQUID circuit is enhanced by additional positive feedback circuit; transfer characteristics of the second-stage SQUID circuit are linearized by an additional negative feedback circuit. Two proportional feedback schemes are cooperated together based on matching conditions to achieve both noise suppression and working point matching. Working principles were verified in experiment results. The overall transfer characteristics achieved have only one working point and are simply adjusted according to the voltage swing of an amplifier. Transfer coefficient of the first-stage SQUID circuit was raised up to 10 (20 dB), and the total flux noise of two-stage SQUID readout circuit was reduced below 1 μΦ0/√Hz, where Φ0= 2.07×10-15Wb. Our two-stage SQUID readout circuit is easy-to-operate and suited for high-performance practical SQUID systems.
A low-noise single-chip two-stage superconducting quantum interference device (SQUID) system with a double relaxation oscillation SQUID as the second stage has been realized. The system was operated in a direct voltage readout mode, with a closed loop bandwidth up to 1 MHz. Operated at 4.2 K, the white flux noise measured in flux locked loop was 1.3 μΦ0/√Hz, corresponding to an energy sensitivity of ε≈27h. Owing to the large flux-to-voltage transfer of up to 3.6 mV/Φ0, the room-temperature preamplifier noise did not dominate the overall flux noise.