Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Technical digest - International Electron Devices Meeting/Technical digest

Dispersive vs charge-sensing readout for linear quantum registers

A. Aprá, Alessandro Crippa, M. L. V. Tagliaferri, J. Li, R. Ezzouch, Benoît Bertrand, Louis Hutin, N. Rambal, E. Catapano, Heimanu Niebojewski, Thomas Bédécarrats, M. Vinet, Matias Urdampilleta, Tristan Meunier, Yann‐Michel Niquet, Étienne Dumur, M. Sanquer, X. Jehl, Romain Maurand, Silvano De Franceschi

Published Dec 12, 2020• 4 citations
Publisher

Abstract

We present recent progress in the implementation of scalable schemes for spin qubit readout in one dimensional quantum registers based on fully-depleted silicon-on-insulator (FDSOI) technology. We compare two schemes both based on rf gate reflectometry. The first one, denoted as dispersive readout, minimizes the device overhead thereby facilitating scale-up to large qubit registers. The second one, denoted as charge-sensing readout, requires additional readout components but is less sensitive to the strength of the interdot coupling facilitating operation in the few-electron regime. We demonstrate single-shot charge sensing with a fidelity of 97% in 5 μs. Finally, we propose a scalable device architecture for linear qubit registers relying on charge-sensing readout.

DOI
10.1109/iedm13553.2020.9372090

Related papers

A High-Sensitivity Charge Sensor for Silicon Qubits above 1 K

Jonathan Y. Huang, Wee Han Lim, Ross C. C. Leon +6 more

Recent studies of silicon spin qubits at temperatures above 1 K are encouraging demonstrations that the cooling requirements for solid-state quantum computing can be considerably relaxed. However, qubit readout mechanisms that rely on charge sensing with a single-island single-electron transistor (SISET) quickly lose sensitivity due to thermal broadening of the electron distribution in the reservoirs. Here we exploit the tunneling between two quantized states in a double-island single-electron transistor (SET) to demonstrate a charge sensor with an improvement in the signal-to-noise ratio by an order of magnitude compared to a standard SISET, and a single-shot charge readout fidelity above 99% up to 8 K at a bandwidth greater than 100 kHz. These improvements are consistent with our theoretical modeling of the temperature-dependent current transport for both types of SETs. With minor additional hardware overhead, these sensors can be integrated into existing qubit architectures for a high-fidelity charge readout at few-kelvin temperatures.

arXiv:2103.06433•Nano Letters•May 17, 2021•17 citations

Dispersive readout of a silicon quantum dot with an accumulation-mode gate sensor

A. Rossi, R. Zhao, Andrew S. Dzurak +1 more

Sensitive charge detection has enabled qubit readout in solid-state systems. Recently, an alternative to the well-established charge detection via on-chip electrometers has emerged, based on in situ gate detectors and radio-frequency dispersive readout techniques. This approach promises to facilitate scalability by removing the need for additional device components devoted to sensing. Here, we perform gate-based dispersive readout of an accumulation-mode silicon quantum dot. We observe that the response of an accumulation-mode gate detector is significantly affected by its bias voltage, particularly if this exceeds the threshold for electron accumulation. We discuss and explain these results in light of the competing capacitive contributions to the dispersive response.

arXiv:1610.00767•Applied Physics Letters•May 22, 2017•22 citations

Gate Dispersive Charge Detection in Ge/SiGe Quantum Dots

Mukhlasur Rahman Tanvir, Ebrahim Sajadi, Menno Veldhorst +2 more

Spin qubits are an attractive platform for scalable quantum computation, and recently, laterally gated quantum dots (QDs) in Ge heterostructures have emerged as a leading implementation. Radio-frequency (RF) single-hole transistor (SHT) spin readout and integrated superconducting resonator charge readout have demonstrated in Ge QDs, but their wiring overhead and on-chip size can pose challenges, while gate dispersive (GD) readout, which requires less on-chip overhead, has yet to be demonstrated for Ge QDs. Here we demonstrate compact, low-overhead RF-GD charge readout of a Ge double QD (DQD), both directly, and assisted by a proximal single-hole box (SHB). We resolve QD loading and interdot transitions with both techniques. We obtain unity signal-to-noise ratio (SNR) in 2.7 millisecond and 135 microsecond integration time, for gate-dispersive detection of the DQD and SHB-DQD systems, respectively. We find that the SHB enhances the interdot signal-to-noise ratio (SNR) of our 540 MHz circuit by a factor of 20 for a DQD coupling $t_c \approx 5$ GHz. Power and temperature dependent measurements verify that SNR is limited by dielectric loss. We argue that with achievable improvements in dielectric loss and amplification, high-fidelity (99\%) readout in less than 1 microsecond should be possible, assuming ideal spin-to-charge conversion, which has seen rapid recent progress. These results establish a simple and compact gate-based readout approach for direct and SHB-enhanced readout of Ge heterostructure QDs.

arXiv:2610.01100•Oct 1, 2026•0 citations

Scalable and high-sensitivity readout of silicon quantum devices

Simon Schaal

Quantum computing is predicted to provide unprecedented enhancements in computational power. A quantum computer requires implementation of a well-defined and controlled quantum system of many interconnected qubits, each defined using fragile quantum states. The interest in a spin-based quantum computer in silicon stems from demonstrations of very long spin-coherence times, high-fidelity single spin control and compatibility with industrial mass-fabrication. Industrial scale fabrication of the silicon platform offers a clear route towards a large-scale quantum computer, however, some of the processes and techniques employed in qubit demonstrators are incompatible with a dense and foundry-fabricated architecture. In particular, spin-readout utilises external sensors that require nearly the same footprint as qubit devices. In this thesis, improved readout techniques for silicon quantum devices are presented and routes towards implementation of a scalable and high-sensitivity readout architecture are investigated. Firstly, readout sensitivity of compact gate-based sensors is improved using a high-quality factor resonator and Josephson parametric amplifier that are fabricated separately from quantum dots. Secondly, an integrated transistor-based control circuit is presented using which sequential readout of two quantum dot devices using the same gate-based sensor is achieved. Finally, a large-scale readout architecture based on random-access and frequency multiplexing is introduced. The impact of readout circuit footprint on readout sensitivity is determined, showing routes towards integration of conventional circuits with quantum devices in a dense architecture, and a fault-tolerant architecture based on mediated exchange is introduced, capable of relaxing the limitations on available control circuit footprint per qubit. Demonstrations are based on foundry-fabricated transistors and few-electron quantum dots, showing that industry fabrication is a viable route towards quantum computation at a scale large enough to begin addressing the most challenging computational problems.

•Jan 28, 2020•0 citations

Radio-Frequency Reflectometry in Silicon-Based Quantum Dots

Y. Y. Liu, Stephan G. J. Philips, Lucas Orona +6 more

Radio-frequency (rf) reflectometry offers a fast and sensitive method for charge sensing and spin readout in gated quantum dots. We focus in this work on the implementation of rf readout in accumulation-mode gate-defined quantum dots, where the large parasitic capacitance poses a challenge. We describe and test two methods for mitigating the effect of the parasitic capacitance, one by on-chip modifications and a second by off-chip changes. We demonstrate that on-chip modifications enable high-performance charge readout in $\mathrm{Si}$/${\mathrm{Si}}_{x}$${\mathrm{Ge}}_{1\ensuremath{-}x}$ quantum dots, achieving a fidelity of 99.9% for a measurement time of $1\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{s}$.

arXiv:2012.14560•Physical Review Applied•Jul 23, 2021•35 citations

Dispersive Readout of a Few-Electron Double Quantum Dot with Fast rf Gate Sensors

James Colless, Alice Mahoney, J. M. Hornibrook +4 more

We report the dispersive charge-state readout of a double quantum dot in the few-electron regime using the in situ gate electrodes as sensitive detectors. We benchmark this gate sensing technique against the well established quantum point contact charge detector and find comparable performance with a bandwidth of $\ensuremath{\sim}10\text{ }\text{ }\mathrm{MHz}$ and an equivalent charge sensitivity of $\ensuremath{\sim}6.3\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}3}\text{ }\text{ }e/\sqrt{\mathrm{Hz}}$. Dispersive gate sensing alleviates the burden of separate charge detectors for quantum dot systems and promises to enable readout of qubits in scaled-up arrays.

arXiv:1210.4645•Physical Review Letters•Jan 25, 2013•215 citations
We present recent progress in the implementation of scalable schemes for spin qubit readout in one dimensional quantum registers based on fully-depleted silicon-on-insulator (FDSOI) technology. We compare two schemes both based on rf gate reflectometry. The first one, denoted as dispersive readout, minimizes the device overhead thereby facilitating scale-up to large qubit registers. The second one, denoted as charge-sensing readout, requires additional readout components but is less sensitive to the strength of the interdot coupling facilitating operation in the few-electron regime. We demonstrate single-shot charge sensing with a fidelity of 97% in 5 μs. Finally, we propose a scalable device architecture for linear qubit registers relying on charge-sensing readout.
Recent studies of silicon spin qubits at temperatures above 1 K are encouraging demonstrations that the cooling requirements for solid-state quantum computing can be considerably relaxed. However, qubit readout mechanisms that rely on charge sensing with a single-island single-electron transistor (SISET) quickly lose sensitivity due to thermal broadening of the electron distribution in the reservoirs. Here we exploit the tunneling between two quantized states in a double-island single-electron transistor (SET) to demonstrate a charge sensor with an improvement in the signal-to-noise ratio by an order of magnitude compared to a standard SISET, and a single-shot charge readout fidelity above 99% up to 8 K at a bandwidth greater than 100 kHz. These improvements are consistent with our theoretical modeling of the temperature-dependent current transport for both types of SETs. With minor additional hardware overhead, these sensors can be integrated into existing qubit architectures for a high-fidelity charge readout at few-kelvin temperatures.
Sensitive charge detection has enabled qubit readout in solid-state systems. Recently, an alternative to the well-established charge detection via on-chip electrometers has emerged, based on in situ gate detectors and radio-frequency dispersive readout techniques. This approach promises to facilitate scalability by removing the need for additional device components devoted to sensing. Here, we perform gate-based dispersive readout of an accumulation-mode silicon quantum dot. We observe that the response of an accumulation-mode gate detector is significantly affected by its bias voltage, particularly if this exceeds the threshold for electron accumulation. We discuss and explain these results in light of the competing capacitive contributions to the dispersive response.
Spin qubits are an attractive platform for scalable quantum computation, and recently, laterally gated quantum dots (QDs) in Ge heterostructures have emerged as a leading implementation. Radio-frequency (RF) single-hole transistor (SHT) spin readout and integrated superconducting resonator charge readout have demonstrated in Ge QDs, but their wiring overhead and on-chip size can pose challenges, while gate dispersive (GD) readout, which requires less on-chip overhead, has yet to be demonstrated for Ge QDs. Here we demonstrate compact, low-overhead RF-GD charge readout of a Ge double QD (DQD), both directly, and assisted by a proximal single-hole box (SHB). We resolve QD loading and interdot transitions with both techniques. We obtain unity signal-to-noise ratio (SNR) in 2.7 millisecond and 135 microsecond integration time, for gate-dispersive detection of the DQD and SHB-DQD systems, respectively. We find that the SHB enhances the interdot signal-to-noise ratio (SNR) of our 540 MHz circuit by a factor of 20 for a DQD coupling tc≈5t_c \approx 5tc​≈5 GHz. Power and temperature dependent measurements verify that SNR is limited by dielectric loss. We argue that with achievable improvements in dielectric loss and amplification, high-fidelity (99\%) readout in less than 1 microsecond should be possible, assuming ideal spin-to-charge conversion, which has seen rapid recent progress. These results establish a simple and compact gate-based readout approach for direct and SHB-enhanced readout of Ge heterostructure QDs.
Quantum computing is predicted to provide unprecedented enhancements in computational power. A quantum computer requires implementation of a well-defined and controlled quantum system of many interconnected qubits, each defined using fragile quantum states. The interest in a spin-based quantum computer in silicon stems from demonstrations of very long spin-coherence times, high-fidelity single spin control and compatibility with industrial mass-fabrication. Industrial scale fabrication of the silicon platform offers a clear route towards a large-scale quantum computer, however, some of the processes and techniques employed in qubit demonstrators are incompatible with a dense and foundry-fabricated architecture. In particular, spin-readout utilises external sensors that require nearly the same footprint as qubit devices. In this thesis, improved readout techniques for silicon quantum devices are presented and routes towards implementation of a scalable and high-sensitivity readout architecture are investigated. Firstly, readout sensitivity of compact gate-based sensors is improved using a high-quality factor resonator and Josephson parametric amplifier that are fabricated separately from quantum dots. Secondly, an integrated transistor-based control circuit is presented using which sequential readout of two quantum dot devices using the same gate-based sensor is achieved. Finally, a large-scale readout architecture based on random-access and frequency multiplexing is introduced. The impact of readout circuit footprint on readout sensitivity is determined, showing routes towards integration of conventional circuits with quantum devices in a dense architecture, and a fault-tolerant architecture based on mediated exchange is introduced, capable of relaxing the limitations on available control circuit footprint per qubit. Demonstrations are based on foundry-fabricated transistors and few-electron quantum dots, showing that industry fabrication is a viable route towards quantum computation at a scale large enough to begin addressing the most challenging computational problems.
Radio-frequency (rf) reflectometry offers a fast and sensitive method for charge sensing and spin readout in gated quantum dots. We focus in this work on the implementation of rf readout in accumulation-mode gate-defined quantum dots, where the large parasitic capacitance poses a challenge. We describe and test two methods for mitigating the effect of the parasitic capacitance, one by on-chip modifications and a second by off-chip changes. We demonstrate that on-chip modifications enable high-performance charge readout in Si\mathrm{Si}Si/Six{\mathrm{Si}}_{x}Six​${\mathrm{Ge}}_{1\ensuremath{-}x}$ quantum dots, achieving a fidelity of 99.9% for a measurement time of $1\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{s}$.
We report the dispersive charge-state readout of a double quantum dot in the few-electron regime using the in situ gate electrodes as sensitive detectors. We benchmark this gate sensing technique against the well established quantum point contact charge detector and find comparable performance with a bandwidth of $\ensuremath{\sim}10\text{ }\text{ }\mathrm{MHz}$ and an equivalent charge sensitivity of $\ensuremath{\sim}6.3\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}3}\text{ }\text{ }e/\sqrt{\mathrm{Hz}}$. Dispersive gate sensing alleviates the burden of separate charge detectors for quantum dot systems and promises to enable readout of qubits in scaled-up arrays.