Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2103.06433 · Nano Letters

A High-Sensitivity Charge Sensor for Silicon Qubits above 1 K

Jonathan Y. Huang, Wee Han Lim, Ross C. C. Leon, Chih Hwan Yang, Fay E. Hudson, Christopher C. Escott, André Saraiva, Andrew S. Dzurak, Arne Laucht

Published May 17, 2021• 17 citations
arXivHTMLPDF

Abstract

Recent studies of silicon spin qubits at temperatures above 1 K are encouraging demonstrations that the cooling requirements for solid-state quantum computing can be considerably relaxed. However, qubit readout mechanisms that rely on charge sensing with a single-island single-electron transistor (SISET) quickly lose sensitivity due to thermal broadening of the electron distribution in the reservoirs. Here we exploit the tunneling between two quantized states in a double-island single-electron transistor (SET) to demonstrate a charge sensor with an improvement in the signal-to-noise ratio by an order of magnitude compared to a standard SISET, and a single-shot charge readout fidelity above 99% up to 8 K at a bandwidth greater than 100 kHz. These improvements are consistent with our theoretical modeling of the temperature-dependent current transport for both types of SETs. With minor additional hardware overhead, these sensors can be integrated into existing qubit architectures for a high-fidelity charge readout at few-kelvin temperatures.

DOI
10.1021/acs.nanolett.1c01003

Related papers

Improved Single-Shot Qubit Readout Using Twin rf-SET Charge Correlations

Santiago Serrano, MengKe Feng, Wee Han Lim +11 more

High-fidelity qubit readout is critical in order to obtain the thresholds needed to implement quantum error-correction protocols and achieve fault-tolerant quantum computing. Large-scale silicon qubit devices will have densely packed arrays of quantum dots with multiple charge sensors that are, on average, farther away from the quantum dots, entailing a reduction in readout fidelities. Here, we present a readout technique that enhances the readout fidelity in a linear SiMOS four-dot array by amplifying correlations between a pair of single-electron transistors, known as a twin SET. By recording and subsequently correlating the twin SET traces as we modulate the dot detuning across a charge transition, we demonstrate a reduction in the charge readout infidelity by over one order of magnitude compared to traditional readout methods. We also study the spin-to-charge conversion errors introduced by the modulation technique and conclude that faster modulation frequencies avoid relaxation-induced errors without introducing significant spin-flip errors, favoring the use of the technique at short integration times. This method not only allows for faster and higher-fidelity qubit measurements but it also enhances the signal corresponding to charge transitions that take place farther away from the sensors, enabling a way to circumvent the reduction in readout fidelities in large arrays of qubits. Published by the American Physical Society 2024

arXiv:2307.07724•PRX Quantum•Jan 3, 2024•9 citations

Modelling single-electron-transistor-based readout in the Kane solid-state quantum computer

Chris I. Pakes, Vincent I. Conrad, J C Ang +5 more

The Kane (Kane B E 1998 Nature 393 133) solid-state quantum computer aims to exploit as qubits an array of 31 P nuclear spins embedded in a silicon matrix. A proposed scheme for readout of a qubit spin state relies on measurement of the associated spin state of its donor electron, by attempting to induce and detect, using a single-electron transistor (SET), spin-polarized motion of the electron to an adjacent donor site. The sensitivity required of a SET for detection of sub-surface electronic charge motion in a MOS architecture is examined by simulation of the capacitive coupling of the buried charge to the SET device. It is shown that the SET can support readout of the qubit electronic charge states within the appropriate electron spin relaxation time. This paper presents a novel application of Technology Computer Aided Design, which presents itself as a valuable tool for the design of nanoscale device architectures employing precision electrometry for readout of quantum logic states.

Nanotechnology•Jan 10, 2003•5 citations

Nanoscale single-electron transistor architectures for single spin detection in solid state quantum computer devices

Tilo M. Buehler, R. Brenner, D. J. Reilly +3 more

Single-spin detection will be crucial for solid-state quantum computer architectures in which information is encoded in the spin-state of single nuclear or electron spins. The formidable problem of single-spin detection in a solid can be mapped to a more tractable problem of single-charge detection through spin-dependent electron transfer which may be observed using ultra-sensitive solid-state nanostructure electrometers. Here we describe a readout architecture using single electron transistors (SETs) that can detect the charge-state of two coupled metal dots, which simulates charge transfer in a two-quantum bit (qubit) spin system. This twin-SET architecture allows significant reduction of random charge noise by correlating two detector outputs, reducing the probability of readout errors in the quantum computer.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 19, 2001•0 citations

A Superconducting Phase Transition Single-Electron Transistor

Gorka Aizpurua-Iraola, Thomas H. Swift, Felix-Ekkehard von Horstig +6 more

Quantum computers require fast and accurate methods for qubit state detection. Phase-transition sensors exploit the abrupt change between two physical states of a material to achieve enhanced sensitivity and have enabled advanced detectors for quantum technologies, such as superconducting nanowire single-photon detectors. However, this sensing principle has not yet been applied to semiconductor spin qubits. Here, we demonstrate a superconducting phase-transition radio-frequency single-electron transistor (PTSET), a charge sensor for semiconductor spin qubits whose response is enhanced by a superconducting-to-normal phase transition. The transition is engineered by linking the sensor current to a low-critical-current, high-kinetic-inductance inductor integrated into the radio-frequency matching network. We demonstrate improvements in sensitivity of one and two orders of magnitude over conventional rfSETs in the large- and small-signal regimes, respectively. Our results establish phase-transition sensing as a route towards ultrasensitive, integrated charge sensors for semiconductor quantum computing and point to broader applications, including cryogenic photon detection for radio astronomy.

quant-pharXiv:2608.27045•Aug 28, 2026•1 citation

Simultaneous readout of two charge qubits

Jian Li, Göran Johansson

We consider a system of two solid state charge qubits, coupled to a single readout device, consisting of a single-electron transistor (SET). The conductance of each tunnel junction is influenced by its neighboring qubit, and thus the current through the transistor is determined by the qubits' state. The full counting statistics of the electrons passing the transistor is calculated, and we discuss qubit dephasing, as well as the quantum efficiency of the readout. The current measurement is then compared to readout using real-time detection of the SET island's charge state. For the latter method we show that the quantum efficiency is always unity. Comparing the two methods a simple geometrical interpretation of the quantum efficiency of the current measurement appears. Finally, we note that full quantum efficiency in some cases can be achieved measuring the average charge of the SET island, in addition to the average current.

arXiv:cond-mat/0611143•Physical Review B•Feb 9, 2007•8 citations

Improving the Readout of Semiconducting Qubits

Matthew Curry

Semiconducting qubits are a promising platform for quantum computers. In particular, silicon spin qubits have made a number of advancements recently including long coherence times, high-fidelity single-qubit gates, two-qubit gates, and high-fidelity readout. However, all operations likely require improvement in fidelity and speed, if possible, to realize a quantum computer. Readout fidelity and speed, in general, are limited by circuit challenges centered on extracting low signal from a device in a dilution refrigerator connected to room temperature amplifiers by long coaxial cables with relatively high capacitance. Readout fidelity specifically is limited by the time it takes to reliably distinguish qubit states relative to the characteristic decay time of the excited state, T1. This dissertation explores the use of heterojunction bipolar transistor (HBT) circuits to amplify the readout signal of silicon spin qubits at cryogenic temperatures. The cryogenic amplification approach has numerous advantages including low implementation overhead, low power relative to the available cooling power, and high signal gain at the mixing chamber stage leading to around a factor of ten speedup in readout time for a similar signal-to-noise ratio. The faster readout time generally increases fidelity, since it is much faster than the T1 time. Two HBT amplification circuits have been designed and characterized. One design is a low-power, base-current biased configuration with non-linear gain (CB-HBT), and the second is a linear-gain, AC-coupled configuration (AC-HBT). They can operate at powers of 1 and 10 μW, respectfully, and not significantly heat electrons. The noise spectral density referred to the input for both circuits is around 15 to 30 fA/√Hz, which is low compared to previous cases such as the dual-stage, AC-coupled HEMT circuit at ~ 70 fA/√Hz. Both circuits achieve charge sensitivity between 300 and 400 μe/√Hz, which approaches the best alternatives (e.g., RF-SET at ~ 140 μe/√Hz) but with much less implementation overhead. For the single-shot latched charge readout performed, both circuits achieve high-fidelity readout in times < 10 μs with bit error rates < 10-3, which is a great improvement over previous work at > 70 μs. The readout speed-up in principle also reduces the production of errors due to excited state relaxation by a factor of ~ 10. All of these results are possible with relatively simple, low-power transistor circuits which can be mounted close to the qubit device at the mixing chamber stage of the dilution refrigerator.

•Jan 1, 2019•0 citations
Recent studies of silicon spin qubits at temperatures above 1 K are encouraging demonstrations that the cooling requirements for solid-state quantum computing can be considerably relaxed. However, qubit readout mechanisms that rely on charge sensing with a single-island single-electron transistor (SISET) quickly lose sensitivity due to thermal broadening of the electron distribution in the reservoirs. Here we exploit the tunneling between two quantized states in a double-island single-electron transistor (SET) to demonstrate a charge sensor with an improvement in the signal-to-noise ratio by an order of magnitude compared to a standard SISET, and a single-shot charge readout fidelity above 99% up to 8 K at a bandwidth greater than 100 kHz. These improvements are consistent with our theoretical modeling of the temperature-dependent current transport for both types of SETs. With minor additional hardware overhead, these sensors can be integrated into existing qubit architectures for a high-fidelity charge readout at few-kelvin temperatures.
High-fidelity qubit readout is critical in order to obtain the thresholds needed to implement quantum error-correction protocols and achieve fault-tolerant quantum computing. Large-scale silicon qubit devices will have densely packed arrays of quantum dots with multiple charge sensors that are, on average, farther away from the quantum dots, entailing a reduction in readout fidelities. Here, we present a readout technique that enhances the readout fidelity in a linear SiMOS four-dot array by amplifying correlations between a pair of single-electron transistors, known as a twin SET. By recording and subsequently correlating the twin SET traces as we modulate the dot detuning across a charge transition, we demonstrate a reduction in the charge readout infidelity by over one order of magnitude compared to traditional readout methods. We also study the spin-to-charge conversion errors introduced by the modulation technique and conclude that faster modulation frequencies avoid relaxation-induced errors without introducing significant spin-flip errors, favoring the use of the technique at short integration times. This method not only allows for faster and higher-fidelity qubit measurements but it also enhances the signal corresponding to charge transitions that take place farther away from the sensors, enabling a way to circumvent the reduction in readout fidelities in large arrays of qubits. Published by the American Physical Society 2024
The Kane (Kane B E 1998 Nature 393 133) solid-state quantum computer aims to exploit as qubits an array of 31 P nuclear spins embedded in a silicon matrix. A proposed scheme for readout of a qubit spin state relies on measurement of the associated spin state of its donor electron, by attempting to induce and detect, using a single-electron transistor (SET), spin-polarized motion of the electron to an adjacent donor site. The sensitivity required of a SET for detection of sub-surface electronic charge motion in a MOS architecture is examined by simulation of the capacitive coupling of the buried charge to the SET device. It is shown that the SET can support readout of the qubit electronic charge states within the appropriate electron spin relaxation time. This paper presents a novel application of Technology Computer Aided Design, which presents itself as a valuable tool for the design of nanoscale device architectures employing precision electrometry for readout of quantum logic states.
Single-spin detection will be crucial for solid-state quantum computer architectures in which information is encoded in the spin-state of single nuclear or electron spins. The formidable problem of single-spin detection in a solid can be mapped to a more tractable problem of single-charge detection through spin-dependent electron transfer which may be observed using ultra-sensitive solid-state nanostructure electrometers. Here we describe a readout architecture using single electron transistors (SETs) that can detect the charge-state of two coupled metal dots, which simulates charge transfer in a two-quantum bit (qubit) spin system. This twin-SET architecture allows significant reduction of random charge noise by correlating two detector outputs, reducing the probability of readout errors in the quantum computer.
Quantum computers require fast and accurate methods for qubit state detection. Phase-transition sensors exploit the abrupt change between two physical states of a material to achieve enhanced sensitivity and have enabled advanced detectors for quantum technologies, such as superconducting nanowire single-photon detectors. However, this sensing principle has not yet been applied to semiconductor spin qubits. Here, we demonstrate a superconducting phase-transition radio-frequency single-electron transistor (PTSET), a charge sensor for semiconductor spin qubits whose response is enhanced by a superconducting-to-normal phase transition. The transition is engineered by linking the sensor current to a low-critical-current, high-kinetic-inductance inductor integrated into the radio-frequency matching network. We demonstrate improvements in sensitivity of one and two orders of magnitude over conventional rfSETs in the large- and small-signal regimes, respectively. Our results establish phase-transition sensing as a route towards ultrasensitive, integrated charge sensors for semiconductor quantum computing and point to broader applications, including cryogenic photon detection for radio astronomy.
We consider a system of two solid state charge qubits, coupled to a single readout device, consisting of a single-electron transistor (SET). The conductance of each tunnel junction is influenced by its neighboring qubit, and thus the current through the transistor is determined by the qubits' state. The full counting statistics of the electrons passing the transistor is calculated, and we discuss qubit dephasing, as well as the quantum efficiency of the readout. The current measurement is then compared to readout using real-time detection of the SET island's charge state. For the latter method we show that the quantum efficiency is always unity. Comparing the two methods a simple geometrical interpretation of the quantum efficiency of the current measurement appears. Finally, we note that full quantum efficiency in some cases can be achieved measuring the average charge of the SET island, in addition to the average current.
Semiconducting qubits are a promising platform for quantum computers. In particular, silicon spin qubits have made a number of advancements recently including long coherence times, high-fidelity single-qubit gates, two-qubit gates, and high-fidelity readout. However, all operations likely require improvement in fidelity and speed, if possible, to realize a quantum computer. Readout fidelity and speed, in general, are limited by circuit challenges centered on extracting low signal from a device in a dilution refrigerator connected to room temperature amplifiers by long coaxial cables with relatively high capacitance. Readout fidelity specifically is limited by the time it takes to reliably distinguish qubit states relative to the characteristic decay time of the excited state, T1. This dissertation explores the use of heterojunction bipolar transistor (HBT) circuits to amplify the readout signal of silicon spin qubits at cryogenic temperatures. The cryogenic amplification approach has numerous advantages including low implementation overhead, low power relative to the available cooling power, and high signal gain at the mixing chamber stage leading to around a factor of ten speedup in readout time for a similar signal-to-noise ratio. The faster readout time generally increases fidelity, since it is much faster than the T1 time. Two HBT amplification circuits have been designed and characterized. One design is a low-power, base-current biased configuration with non-linear gain (CB-HBT), and the second is a linear-gain, AC-coupled configuration (AC-HBT). They can operate at powers of 1 and 10 μW, respectfully, and not significantly heat electrons. The noise spectral density referred to the input for both circuits is around 15 to 30 fA/√Hz, which is low compared to previous cases such as the dual-stage, AC-coupled HEMT circuit at ~ 70 fA/√Hz. Both circuits achieve charge sensitivity between 300 and 400 μe/√Hz, which approaches the best alternatives (e.g., RF-SET at ~ 140 μe/√Hz) but with much less implementation overhead. For the single-shot latched charge readout performed, both circuits achieve high-fidelity readout in times < 10 μs with bit error rates < 10-3, which is a great improvement over previous work at > 70 μs. The readout speed-up in principle also reduces the production of errors due to excited state relaxation by a factor of ~ 10. All of these results are possible with relatively simple, low-power transistor circuits which can be mounted close to the qubit device at the mixing chamber stage of the dilution refrigerator.