Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Fabrication Process SIS Junctions for 40 GHz SIS Receiver

Akira Sakamoto, Takehiro Noguchi

Published Jan 1, 1996• 0 citations
OpenAlex

Related papers

Fabrication and Characterization of a 600 GHz Resonant Distributed SIS Junction for Fixed-tuned Waveguide Receiver

T. Matsunaga, Edward Tong, Takashi Noguchi +1 more

•Jun 1, 2001•1 citation

An 850 GHz Waveguide Receiver Using a Tuned Nb SIS Tunnel Junction Fabricated on a 1μm Si 3 N 4 Membrane

J. Kooi, Mansun Chan, Paul Schaffer⧧ +4 more

Softwaretechnik-Trends•Mar 1, 1996•2 citations

First results of a 36 GHz SIS receiver

Denis Cr�t�, J. C. Pernot, Christine Letrou +1 more

International Journal of Infrared and Millimeter Waves•Jul 1, 1984•0 citations

SIS Mixer Fabrication for ALMA Band10

M. Kroug, Akira Endo, T. Tamura +6 more

Band10 of the Atacama Large Millimeter Array (ALMA) is a planned heterodyne receiver covering the frequency range 790 GHz-950 GHz. The waveguide mixers are superconductor insulator superconductor (SIS) Nb/Al-AlOx/Nb junctions integrated with NbTiN/SiO2/Al tuning circuits. Our junction definition process has been greatly simplified by introducing an inductively-coupled-plasma (ICP) etcher to the fabrication. The etching process, which employs a low-pressure CF4/O2plasma, allows to remove the entire Nb/Al-AlOx/Nb tri-layer in asinglestep. SIS mixers with current densities up to 10 kA/cm2and quality factor above 15 have been fabricated with good reproducibility. Minimum receiver noise temperature, corrected for optical losses, is 210 K at 860 GHz. With the goal to further improve the performance, optimization of circuit design and fabrication technology are discussed.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•24 citations

205 GHz SIS Receiver Development

William R. McGrath, C. N. Byrom, B. N. Ellison +4 more

Astrophysics and space science library•Jan 1, 1990•1 citation

Design, fabrication, and experimental characterization of a 300-GHz-band SIS mixer prototype for the BHEX mission

Yosuke Murayama, Edward Tong, Takafumi Kojima +8 more

We report the design, fabrication, and experimental characterization of a 300-GHz-band superconductor-insulator-superconductor (SIS) mixer prototype for the Black Hole Explorer (BHEX) mission. The mixer employs a three-junction series SIS array, a waveguide probe with a microstrip impedance transformer, and an on-chip IF tuning circuit. As a first implementation of the baseline RF design, the mixer chip was fabricated using an established aluminum-oxide-barrier SIS junction process. Test junctions on the same wafer showed a critical current density of approximately 12 kA/cm2. The fabricated mixer chip was mounted in a waveguide mixer block and evaluated at a mixer-block temperature of 4 K by the Y-factor method. The measured double-sideband receiver noise temperature was 26–41 K at LO frequencies of 240–307 GHz. At 285 GHz, a noise temperature of approximately 30 K was obtained over the 4–9 GHz IF band, close to the two-photon sensitivity target adopted for the BHEX SIS receiver. These results demonstrate low-noise operation of the first prototype and provide feedback for improving RF/IF bandwidth and mixer stability in subsequent designs.

IEEE Transactions on Terahertz Science and Technology•Jan 1, 2026•0 citations
Band10 of the Atacama Large Millimeter Array (ALMA) is a planned heterodyne receiver covering the frequency range 790 GHz-950 GHz. The waveguide mixers are superconductor insulator superconductor (SIS) Nb/Al-AlOx/Nb junctions integrated with NbTiN/SiO2/Al tuning circuits. Our junction definition process has been greatly simplified by introducing an inductively-coupled-plasma (ICP) etcher to the fabrication. The etching process, which employs a low-pressure CF4/O2plasma, allows to remove the entire Nb/Al-AlOx/Nb tri-layer in asinglestep. SIS mixers with current densities up to 10 kA/cm2and quality factor above 15 have been fabricated with good reproducibility. Minimum receiver noise temperature, corrected for optical losses, is 210 K at 860 GHz. With the goal to further improve the performance, optimization of circuit design and fabrication technology are discussed.
We report the design, fabrication, and experimental characterization of a 300-GHz-band superconductor-insulator-superconductor (SIS) mixer prototype for the Black Hole Explorer (BHEX) mission. The mixer employs a three-junction series SIS array, a waveguide probe with a microstrip impedance transformer, and an on-chip IF tuning circuit. As a first implementation of the baseline RF design, the mixer chip was fabricated using an established aluminum-oxide-barrier SIS junction process. Test junctions on the same wafer showed a critical current density of approximately 12 kA/cm2. The fabricated mixer chip was mounted in a waveguide mixer block and evaluated at a mixer-block temperature of 4 K by the Y-factor method. The measured double-sideband receiver noise temperature was 26–41 K at LO frequencies of 240–307 GHz. At 285 GHz, a noise temperature of approximately 30 K was obtained over the 4–9 GHz IF band, close to the two-photon sensitivity target adopted for the BHEX SIS receiver. These results demonstrate low-noise operation of the first prototype and provide feedback for improving RF/IF bandwidth and mixer stability in subsequent designs.