Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Terahertz Science and Technology

Design, fabrication, and experimental characterization of a 300-GHz-band SIS mixer prototype for the BHEX mission

Yosuke Murayama, Edward Tong, Takafumi Kojima, Wenlei Shan, Yasunori Fujii, Haoran Kang, Takeshi Sakai, Eugene Lauria, Keara Carter, Mareki Honma, Yoshinori Uzawa

Published Jan 1, 2026• 0 citations
Publisher

Abstract

We report the design, fabrication, and experimental characterization of a 300-GHz-band superconductor-insulator-superconductor (SIS) mixer prototype for the Black Hole Explorer (BHEX) mission. The mixer employs a three-junction series SIS array, a waveguide probe with a microstrip impedance transformer, and an on-chip IF tuning circuit. As a first implementation of the baseline RF design, the mixer chip was fabricated using an established aluminum-oxide-barrier SIS junction process. Test junctions on the same wafer showed a critical current density of approximately 12 kA/cm2. The fabricated mixer chip was mounted in a waveguide mixer block and evaluated at a mixer-block temperature of 4 K by the Y-factor method. The measured double-sideband receiver noise temperature was 26–41 K at LO frequencies of 240–307 GHz. At 285 GHz, a noise temperature of approximately 30 K was obtained over the 4–9 GHz IF band, close to the two-photon sensitivity target adopted for the BHEX SIS receiver. These results demonstrate low-noise operation of the first prototype and provide feedback for improving RF/IF bandwidth and mixer stability in subsequent designs.

DOI
10.1109/tthz.2026.3751963

Related papers

Waveguide-Type SIS Receiver Using All-NbN Technique

M. TAKEDA

This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.

IEICE Transactions on Electronics•Feb 1, 2006•5 citations

A 385-500 GHz Low Noise Superconductor-Insulator- Superconductor Mixer for ALMA Band 8

Wenlei Shan

We report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm(2) and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. A parallel-connected twin-junction (PCTJ) is designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it easy to match the low-impedance PCTJ over a wide frequency band. The RF embedding impedance is retrieved by fitting the measured pumped I-V curves to confirm good matching between PCTJ and signal source. We demonstrate here a minimum double-sideband receiver noise temperature of 3 times of quantum limits for an intermediate-frequency range of 4-8 GHz. The mixers were measured in band 8 cartridge with a sideband separation scheme. Single-sideband receiver noise below ALMA specification was achieved over the whole band.

IEICE Transactions on Electronics•Feb 1, 2006•11 citations

Design and Development of SIS Mixers for ALMA Band 10

Wenlei Shan, Sheng‐Cai Shi, T. Matsunaga +4 more

We present the design and preliminary experimental results of superconductor-insulator-superconductor (SIS) mixers for Atacama large millimeter array (ALMA) band 10 (780-950GHz) receivers. To achieve wide frequency coverage as well as low noise temperature, we integrated high current density (10 kA/cm2) and small-sized (one micrometer in diameter) Nb/AlOx/Nb SIS junctions with a tuning microstrip line using NbTiN ground plane and Al wiring layers. High quality NbTiN films with Tc reaching 14.5 K and Al films with residual resistivity ratio as large as 15 have been achieved. To minimize the waveguide transmission loss and facilitate the fabrication of mixer block, a full height waveguide was adopted. The waveguide probe was optimized to achieve low input impedance in the frequency range of 780-950 GHz while adopting a backshort cavity of zero depth. Preliminary RF testing with a Nb/Al microstrip tuning circuit demonstrated a DSB receiver noise temperature about 400 K at 832.5 GHz, which promises the accommodation of receiver performance in ALMA specification with low loss NbTiN/Al microstrip lines.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•40 citations

Wide If 230-GHz Superconductor-Insulator-Superconductor Mixer

Naeun Shin, Jung‐Won Lee, Ming-Jye Wang

A 230 GHz Superconductor-Insulator-Superconductor (SIS) mixer is designed focusing on a good performance in the IF frequency range of 4–16 GHz over the RF band from 211 to 275 GHz. A transition from a full-height waveguide to a probe is designed using HFSS. The mixer chips containing SIS junctions are designed and optimized to have low total capacitance of circuits to ensure wide IF bandwidth. The chip fabrication was done in Academia Sinica Institute of Astronomy and Astrophysics (ASIAA), where the masks were conducted by TSMC. A lab test was conducted on a superconducting mixer with a cryogenic dewar. The gap voltage in the I-V curve of the mixer is approximately 8 mV, and there is a clear nonlinearity around a current of 110 μA, which matches well with the simulation. The receiver noise temperature is approximately 60 K including optical losses and the noise from the RF input.

International Conference on Information and Communication Technology Convergence (ICTC)•Oct 16, 2024•1 citation

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations

Design and Development of SIS Mixers for ALMA Band 8

Wenlei Shan, Takashi Noguchi, S. C. Shi +1 more

In this paper, we report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm/sup 2/ and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. Parallel-connected twin junctions (PCTJ) are designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it much easier to match the low-impedance PCTJ over a wide frequency band. In addition, a superconducting magnet fixed onto the compact mixer block to provide efficient magnetic field coupling is designed. The SIS mixer demonstrates a minimum double-sideband receiver noise temperature of 108 K at the band center and temperatures of less than 167 K over the whole band (for an intermediate-frequency range of 4-8 GHz).

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•27 citations
We report the design, fabrication, and experimental characterization of a 300-GHz-band superconductor-insulator-superconductor (SIS) mixer prototype for the Black Hole Explorer (BHEX) mission. The mixer employs a three-junction series SIS array, a waveguide probe with a microstrip impedance transformer, and an on-chip IF tuning circuit. As a first implementation of the baseline RF design, the mixer chip was fabricated using an established aluminum-oxide-barrier SIS junction process. Test junctions on the same wafer showed a critical current density of approximately 12 kA/cm2. The fabricated mixer chip was mounted in a waveguide mixer block and evaluated at a mixer-block temperature of 4 K by the Y-factor method. The measured double-sideband receiver noise temperature was 26–41 K at LO frequencies of 240–307 GHz. At 285 GHz, a noise temperature of approximately 30 K was obtained over the 4–9 GHz IF band, close to the two-photon sensitivity target adopted for the BHEX SIS receiver. These results demonstrate low-noise operation of the first prototype and provide feedback for improving RF/IF bandwidth and mixer stability in subsequent designs.
This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.
We report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm(2) and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. A parallel-connected twin-junction (PCTJ) is designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it easy to match the low-impedance PCTJ over a wide frequency band. The RF embedding impedance is retrieved by fitting the measured pumped I-V curves to confirm good matching between PCTJ and signal source. We demonstrate here a minimum double-sideband receiver noise temperature of 3 times of quantum limits for an intermediate-frequency range of 4-8 GHz. The mixers were measured in band 8 cartridge with a sideband separation scheme. Single-sideband receiver noise below ALMA specification was achieved over the whole band.
We present the design and preliminary experimental results of superconductor-insulator-superconductor (SIS) mixers for Atacama large millimeter array (ALMA) band 10 (780-950GHz) receivers. To achieve wide frequency coverage as well as low noise temperature, we integrated high current density (10 kA/cm2) and small-sized (one micrometer in diameter) Nb/AlOx/Nb SIS junctions with a tuning microstrip line using NbTiN ground plane and Al wiring layers. High quality NbTiN films with Tc reaching 14.5 K and Al films with residual resistivity ratio as large as 15 have been achieved. To minimize the waveguide transmission loss and facilitate the fabrication of mixer block, a full height waveguide was adopted. The waveguide probe was optimized to achieve low input impedance in the frequency range of 780-950 GHz while adopting a backshort cavity of zero depth. Preliminary RF testing with a Nb/Al microstrip tuning circuit demonstrated a DSB receiver noise temperature about 400 K at 832.5 GHz, which promises the accommodation of receiver performance in ALMA specification with low loss NbTiN/Al microstrip lines.
A 230 GHz Superconductor-Insulator-Superconductor (SIS) mixer is designed focusing on a good performance in the IF frequency range of 4–16 GHz over the RF band from 211 to 275 GHz. A transition from a full-height waveguide to a probe is designed using HFSS. The mixer chips containing SIS junctions are designed and optimized to have low total capacitance of circuits to ensure wide IF bandwidth. The chip fabrication was done in Academia Sinica Institute of Astronomy and Astrophysics (ASIAA), where the masks were conducted by TSMC. A lab test was conducted on a superconducting mixer with a cryogenic dewar. The gap voltage in the I-V curve of the mixer is approximately 8 mV, and there is a clear nonlinearity around a current of 110 μA, which matches well with the simulation. The receiver noise temperature is approximately 60 K including optical losses and the noise from the RF input.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
In this paper, we report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm/sup 2/ and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. Parallel-connected twin junctions (PCTJ) are designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it much easier to match the low-impedance PCTJ over a wide frequency band. In addition, a superconducting magnet fixed onto the compact mixer block to provide efficient magnetic field coupling is designed. The SIS mixer demonstrates a minimum double-sideband receiver noise temperature of 108 K at the band center and temperatures of less than 167 K over the whole band (for an intermediate-frequency range of 4-8 GHz).