Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

AIP Advances

Long-time stable and high-performance YBa2Cu3O7 nanoSQUIDs with more interfaces

Jianxin Lin, Deheng Zhang, Lianjun Zhao, Zejun Shi, Qimin Wang, Shenghao Qin

Published Apr 1, 2022• 1 citation
Publisher

Abstract

We report on the fabrication and characterization of nanopatterned superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions in epitaxially grown multilayer YBa2Cu3O7 (YBCO)/SiTrO3 (STO) thin films. Nanopatterning is performed by Ga+ focused ion beam milling. The evolution of the electric transport and noise properties of the YBCO nanoSQUIDs over a time span of more than one year are recorded and analyzed. We find that the multilayer YBCO/STO nanoSQUIDs show stable and high performance over time. The critical current decreases within ∼40 days by 30%–50% and then remains almost constant without obvious decline trend for nanoSQUIDs with STO layer as the interface even more than 380 days, which demonstrates the superiority of STO as the capping layer. Moreover, we find that the multilayer nanoSQUIDs have about an order of magnitude smaller low-frequency excess flux noise (compared to similar single layer devices) with root-mean-square spectral density ∼5–6 µΦ0/Hz1/2 at 1 Hz. For one device, we show that the low-frequency excess noise does not degrade within three months.

DOI
10.1063/5.0086252

Related papers

YBa 2 Cu 3 O 7 nano superconducting quantum interference devices on MgO bicrystal substrates

Jianxin Lin, Benedikt Müller, Julian Linek +5 more

We report on nanopatterned YBa2Cu3O7-δ (YBCO) direct current superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions. The nanoSQUIDs are fabricated by epitaxial growth of 120 nm-thick films of the high-transition temperature cuprate superconductor YBCO via pulsed laser deposition on MgO bicrystal substrates with 24° misorientation angle, followed by sputtering of dAu = 65 nm thick Au. Nanopatterning is performed by Ga focused ion beam (FIB) milling. The SQUID performance is comparable to devices on SrTiO3 (STO), as demonstrated by electric transport and noise measurements at 4.2 K. MgO has orders of magnitude smaller dielectric permittivity than STO; i.e., one may avoid Au as a resistively shunting layer to reduce the intrinsic thermal flux noise of the nanoSQUIDs. However, we find that the Au layer is important for avoiding degradation during FIB milling. Hence, we compare devices with different dAu produced by thinning the Au layer via Ar ion milling after FIB patterning. We find that the reduction of dAu yields an increase in junction resistance, however at the expense of a reduction of the critical current and increase in SQUID inductance. This results in an estimated thermal flux noise that is almost independent of dAu. However, for two devices on MgO with 65 nm-thick Au, we find an order of magnitude lower low-frequency excess noise as compared to nanoSQUIDs on STO or those on MgO with reduced dAu. For one of those devices we obtain with bias-reversal readout ultra-low flux noise of ∼175 nΦ0 Hz-1/2 down to ∼10 Hz.

Nanoscale•Jan 1, 2020•17 citations

Submicron YBa2Cu3O7−δ grain boundary junction dc SQUIDs

M. Kawasaki, P. K. Chaudhari, T. H. Newman +1 more

We have fabricated and measured the properties of micron-size single grain boundary junctions and dc superconducting quantum interference devices (SQUIDs). The width of the junctions was varied between 0.25 and 2 μm. The junctions were formed in c-axis oriented epitaxial films with a single 24° tilt boundary. They were fabricated using electron beam lithography and ion milling. All of the junctions operate at 77 K. The noise properties of SQUIDs made of these junctions have been characterized. They show a significant 1/f component which is comparable to published values. However, the white noise level, 3×10−31 J/Hz measured at 77 K, is the lowest ever reported.

Applied Physics Letters•Jun 3, 1991•59 citations

YBa2Cu3O7− δ superconducting quantum interference devices with metallic to insulating barriers written with a focused helium ion beam

Ethan Y. Cho, M. K., Chuong Huynh +5 more

In this work, we demonstrate the ability to fabricate superconducting quantum interference devices (SQUIDs) by directly writing Josephson junctions into the plane of YBa2Cu3O7−δ thin films with a focused helium ion beam. This technique allows for the control of the Josephson barrier transport properties through the single parameter, ion dose. SQUIDs written with a dose of 4 × 1016 ions/cm2 had metallic barrier junctions that exhibited nearly ideal electrical transport characteristics at 50 K and a flux noise of 20 μΦ0/Hz at 10 Hz. At higher irradiation doses, the SQUIDs had insulating barrier Josephson junctions with a quasi particle energy gap edge at 20 meV.

Applied Physics Letters•Jun 22, 2015•72 citations

Low 1/f noise single-layer YBa2Cu3Ox dc SQUID at 77 K

Gergely Friedl, M. Vildić, Bernhard Roas +6 more

Autonomous single-layer dc superconducting quantum interference devices (SQUIDs) have been prepared from epitaxial, laser-deposited YBa2Cu3Ox films on step edge SrTiO3 and LaAlO3 substrates. For device patterning, a SiOx inhibit technique as well as conventional ethylenediaminetetraacetic wet etch was used. The Josephson junctions are of grain boundary type. Their widths are 5 μm. The SQUID hole is a square of about 5 μm; the SQUID inductance is estimated to be about 20 pH. We obtained a very regular, nonhysteretic flux to voltage modulation over more than 100 flux quanta (Φ0). The maximum voltage signal is of the order of 15 μV peak to peak and the maximum transfer function dV/dΦ at the appropriate flux bias is 50 μV/Φ0 at 77 K. The best value of the equivalent flux noise as measured in the flux locked loop mode is 1.4×10−5 Φ0/Hz1/2 at 1 Hz and 1×10−5 Φ0/Hz1/2 in the white noise region for f≳5 Hz. This results in an energy resolution εn,w(f≳5 Hz)=1×10−29 J/Hz in the white noise region and 2×10−29 J/Hz at 1 Hz.

Applied Physics Letters•Jun 15, 1992•69 citations

Nb nano superconducting quantum interference devices with high spin sensitivity for operation in magnetic fields up to 0.5 T

Roman Wölbing, Joachim Nagel, Tobias Schwarz +7 more

We investigate electric transport and noise properties of microstrip-type submicron direct current superconducting quantum interference devices (dc SQUIDs) based on Nb thin films and overdamped Josephson junctions with a HfTi barrier. The SQUIDs were designed for optimal spin sensitivity Sμ1/2 upon operation in intermediate magnetic fields B (tens of mT), applied perpendicular to the substrate plane. Our, so far, best SQUID can be continuously operated in fields up to B≈±50 mT with rms flux noise SΦ,w1/2≤250 nΦ0/Hz1/2 in the white noise regime and spin sensitivity Sμ1/2≤29 μB/Hz1/2. Furthermore, we demonstrate operation in B = 0.5 T with high sensitivity in flux SΦ,w1/2≈680 nΦ0/Hz1/2 and in electron spin Sμ1/2≈79 μB/Hz1/2. We discuss strategies to further improve the nanoSQUID performance.

arXiv:1304.7584•Applied Physics Letters•May 13, 2013•51 citations

Ultra low noise YBa2Cu3O7−δ nano superconducting quantum interference devices implementing nanowires

Riccardo Arpaia, M. Arzeo, Shahid Nawaz +3 more

We present results on ultra low noise YBa2Cu3O7–δ (YBCO) nano Superconducting QUantum Interference Devices (nanoSQUIDs). To realize such devices, we implemented high quality YBCO nanowires, working as weak links between two electrodes. We observe critical current modulation as a function of an externally applied magnetic field in the full temperature range below the transition temperature TC. The white flux noise below 1μΦ0/Hz at T=8 K makes our nanoSQUIDs very attractive for the detection of small spin systems.

arXiv:1401.6990•Applied Physics Letters•Feb 17, 2014•63 citations
We report on the fabrication and characterization of nanopatterned superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions in epitaxially grown multilayer YBa2Cu3O7 (YBCO)/SiTrO3 (STO) thin films. Nanopatterning is performed by Ga+ focused ion beam milling. The evolution of the electric transport and noise properties of the YBCO nanoSQUIDs over a time span of more than one year are recorded and analyzed. We find that the multilayer YBCO/STO nanoSQUIDs show stable and high performance over time. The critical current decreases within ∼40 days by 30%–50% and then remains almost constant without obvious decline trend for nanoSQUIDs with STO layer as the interface even more than 380 days, which demonstrates the superiority of STO as the capping layer. Moreover, we find that the multilayer nanoSQUIDs have about an order of magnitude smaller low-frequency excess flux noise (compared to similar single layer devices) with root-mean-square spectral density ∼5–6 µΦ0/Hz1/2 at 1 Hz. For one device, we show that the low-frequency excess noise does not degrade within three months.
We report on nanopatterned YBa2Cu3O7-δ (YBCO) direct current superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions. The nanoSQUIDs are fabricated by epitaxial growth of 120 nm-thick films of the high-transition temperature cuprate superconductor YBCO via pulsed laser deposition on MgO bicrystal substrates with 24° misorientation angle, followed by sputtering of dAu = 65 nm thick Au. Nanopatterning is performed by Ga focused ion beam (FIB) milling. The SQUID performance is comparable to devices on SrTiO3 (STO), as demonstrated by electric transport and noise measurements at 4.2 K. MgO has orders of magnitude smaller dielectric permittivity than STO; i.e., one may avoid Au as a resistively shunting layer to reduce the intrinsic thermal flux noise of the nanoSQUIDs. However, we find that the Au layer is important for avoiding degradation during FIB milling. Hence, we compare devices with different dAu produced by thinning the Au layer via Ar ion milling after FIB patterning. We find that the reduction of dAu yields an increase in junction resistance, however at the expense of a reduction of the critical current and increase in SQUID inductance. This results in an estimated thermal flux noise that is almost independent of dAu. However, for two devices on MgO with 65 nm-thick Au, we find an order of magnitude lower low-frequency excess noise as compared to nanoSQUIDs on STO or those on MgO with reduced dAu. For one of those devices we obtain with bias-reversal readout ultra-low flux noise of ∼175 nΦ0 Hz-1/2 down to ∼10 Hz.
We have fabricated and measured the properties of micron-size single grain boundary junctions and dc superconducting quantum interference devices (SQUIDs). The width of the junctions was varied between 0.25 and 2 μm. The junctions were formed in c-axis oriented epitaxial films with a single 24° tilt boundary. They were fabricated using electron beam lithography and ion milling. All of the junctions operate at 77 K. The noise properties of SQUIDs made of these junctions have been characterized. They show a significant 1/f component which is comparable to published values. However, the white noise level, 3×10−31 J/Hz measured at 77 K, is the lowest ever reported.
In this work, we demonstrate the ability to fabricate superconducting quantum interference devices (SQUIDs) by directly writing Josephson junctions into the plane of YBa2Cu3O7−δ thin films with a focused helium ion beam. This technique allows for the control of the Josephson barrier transport properties through the single parameter, ion dose. SQUIDs written with a dose of 4 × 1016 ions/cm2 had metallic barrier junctions that exhibited nearly ideal electrical transport characteristics at 50 K and a flux noise of 20 μΦ0/Hz at 10 Hz. At higher irradiation doses, the SQUIDs had insulating barrier Josephson junctions with a quasi particle energy gap edge at 20 meV.
Autonomous single-layer dc superconducting quantum interference devices (SQUIDs) have been prepared from epitaxial, laser-deposited YBa2Cu3Ox films on step edge SrTiO3 and LaAlO3 substrates. For device patterning, a SiOx inhibit technique as well as conventional ethylenediaminetetraacetic wet etch was used. The Josephson junctions are of grain boundary type. Their widths are 5 μm. The SQUID hole is a square of about 5 μm; the SQUID inductance is estimated to be about 20 pH. We obtained a very regular, nonhysteretic flux to voltage modulation over more than 100 flux quanta (Φ0). The maximum voltage signal is of the order of 15 μV peak to peak and the maximum transfer function dV/dΦ at the appropriate flux bias is 50 μV/Φ0 at 77 K. The best value of the equivalent flux noise as measured in the flux locked loop mode is 1.4×10−5 Φ0/Hz1/2 at 1 Hz and 1×10−5 Φ0/Hz1/2 in the white noise region for f≳5 Hz. This results in an energy resolution εn,w(f≳5 Hz)=1×10−29 J/Hz in the white noise region and 2×10−29 J/Hz at 1 Hz.
We investigate electric transport and noise properties of microstrip-type submicron direct current superconducting quantum interference devices (dc SQUIDs) based on Nb thin films and overdamped Josephson junctions with a HfTi barrier. The SQUIDs were designed for optimal spin sensitivity Sμ1/2 upon operation in intermediate magnetic fields B (tens of mT), applied perpendicular to the substrate plane. Our, so far, best SQUID can be continuously operated in fields up to B≈±50 mT with rms flux noise SΦ,w1/2≤250 nΦ0/Hz1/2 in the white noise regime and spin sensitivity Sμ1/2≤29 μB/Hz1/2. Furthermore, we demonstrate operation in B = 0.5 T with high sensitivity in flux SΦ,w1/2≈680 nΦ0/Hz1/2 and in electron spin Sμ1/2≈79 μB/Hz1/2. We discuss strategies to further improve the nanoSQUID performance.
We present results on ultra low noise YBa2Cu3O7–δ (YBCO) nano Superconducting QUantum Interference Devices (nanoSQUIDs). To realize such devices, we implemented high quality YBCO nanowires, working as weak links between two electrodes. We observe critical current modulation as a function of an externally applied magnetic field in the full temperature range below the transition temperature TC. The white flux noise below 1μΦ0/Hz at T=8 K makes our nanoSQUIDs very attractive for the detection of small spin systems.