Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Operation of a YBa2Cu3Ox rf-SQUID at 81 K | NIST

James Edward Zimmerman, James A. Beall, Michael W. Cromar, Ronald H. Ono

Published Aug 24, 1987• 0 citations
OpenAlex

Related papers

Equivalent Flux Noise in a YBa2CuOx rf SQUID | NIST

James Edward Zimmerman, James A. Beall, Michael W. Cromar +1 more

•Aug 1, 1987•0 citations

Behavior of the dc Impedance of an rf-Biased Resistive SQUID | NIST

D. Vanechten, Robert J. Soulen, Rick Peterson

•Dec 31, 1980•0 citations

Operation of Ceramic rf Squids and Dynamics of Magnetic Flux Vortices

E.V. Ilyichov, V. A. Tulin, V. Zakosarenko

Springer eBooks•Jan 1, 1990•0 citations

Substrate resonator for HTS rf SQUID operation

Y. Zhang, Jürgen Schubert, N. Wolters +3 more

Physica C Superconductivity•Aug 1, 2002•52 citations

Performance of YBaCuO thick film rf SQUIDs at 77 K

Anurag Gupta, Neeraj Khare, Sangeeta Chaudhry +2 more

Pramana•Nov 1, 1990•7 citations

Low 1/f noise single-layer YBa2Cu3Ox dc SQUID at 77 K

Gergely Friedl, M. Vildić, Bernhard Roas +6 more

Autonomous single-layer dc superconducting quantum interference devices (SQUIDs) have been prepared from epitaxial, laser-deposited YBa2Cu3Ox films on step edge SrTiO3 and LaAlO3 substrates. For device patterning, a SiOx inhibit technique as well as conventional ethylenediaminetetraacetic wet etch was used. The Josephson junctions are of grain boundary type. Their widths are 5 μm. The SQUID hole is a square of about 5 μm; the SQUID inductance is estimated to be about 20 pH. We obtained a very regular, nonhysteretic flux to voltage modulation over more than 100 flux quanta (Φ0). The maximum voltage signal is of the order of 15 μV peak to peak and the maximum transfer function dV/dΦ at the appropriate flux bias is 50 μV/Φ0 at 77 K. The best value of the equivalent flux noise as measured in the flux locked loop mode is 1.4×10−5 Φ0/Hz1/2 at 1 Hz and 1×10−5 Φ0/Hz1/2 in the white noise region for f≳5 Hz. This results in an energy resolution εn,w(f≳5 Hz)=1×10−29 J/Hz in the white noise region and 2×10−29 J/Hz at 1 Hz.

Applied Physics Letters•Jun 15, 1992•69 citations
Autonomous single-layer dc superconducting quantum interference devices (SQUIDs) have been prepared from epitaxial, laser-deposited YBa2Cu3Ox films on step edge SrTiO3 and LaAlO3 substrates. For device patterning, a SiOx inhibit technique as well as conventional ethylenediaminetetraacetic wet etch was used. The Josephson junctions are of grain boundary type. Their widths are 5 μm. The SQUID hole is a square of about 5 μm; the SQUID inductance is estimated to be about 20 pH. We obtained a very regular, nonhysteretic flux to voltage modulation over more than 100 flux quanta (Φ0). The maximum voltage signal is of the order of 15 μV peak to peak and the maximum transfer function dV/dΦ at the appropriate flux bias is 50 μV/Φ0 at 77 K. The best value of the equivalent flux noise as measured in the flux locked loop mode is 1.4×10−5 Φ0/Hz1/2 at 1 Hz and 1×10−5 Φ0/Hz1/2 in the white noise region for f≳5 Hz. This results in an energy resolution εn,w(f≳5 Hz)=1×10−29 J/Hz in the white noise region and 2×10−29 J/Hz at 1 Hz.