Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Equivalent Flux Noise in a YBa2CuOx rf SQUID | NIST

James Edward Zimmerman, James A. Beall, Michael W. Cromar, Ronald H. Ono

Published Aug 1, 1987• 0 citations
OpenAlex

Related papers

Operation of a YBa2Cu3Ox rf-SQUID at 81 K | NIST

James Edward Zimmerman, James A. Beall, Michael W. Cromar +1 more

Applied Physics Letters•Aug 24, 1987•0 citations

Behavior of the dc Impedance of an rf-Biased Resistive SQUID | NIST

D. Vanechten, Robert J. Soulen, Rick Peterson

•Dec 31, 1980•0 citations

rf SQUID system as tunable flux qubit

B. Ruggiero, C. Granata, Antonio Vettoliere +5 more

Physics Letters A•Apr 18, 2006•4 citations

rf break-junction SQUID’s at 77 K

I K Harvey, R.A. Binks, R. Driver

Break-junction rf superconducting quantum interference devices (SQUID’s) have been developed using bulk YBa2Cu3O7 ceramic samples which have been fabricated in the laboratory. The SQUID’s have been produced in both single, and two-hole topologies and their noise characteristics have been measured at 77 K. The equivalent flux noise of the two-hole SQUID at a frequency of 200 Hz was found to be 6.8×10−4 flux quantum/(Hz)1/2.

Applied Physics Letters•May 9, 1988•13 citations

Low-frequency Flux Noise in SQUIDs and Superconducting Qubits

S. Sendelbach, David J. Hover, A. Kittel +2 more

Bulletin of the American Physical Society•Mar 11, 2008•0 citations

Use of super Schottky diodes in a cryogenic radio frequency superconducting quantum interference device readout

Michael Mück, Th. Becker, Christoph Heiden

We describe the fabrication and characterization of super Schottky diodes which are used in the cryogenic part of a 3 GHz radio frequency superconducting quantum interference device (rf SQUID) readout electronics. The diodes were prepared on silicon wafers with an n-doping level of 5×1024 m−3. They exhibited sensitivities of 1500 V−1 at 4.2 K, and a noise equivalent power of 2×10−15 W/√Hz was measured at 2.1 GHz. Using planar niobium 3 GHz rf SQUIDs and a cooled rf amplifier, experiments have been performed to investigate the feasibility of these super Schottky diodes for demodulation of the SQUID rf signal voltage. A simple cryogenic rf SQUID readout, employing two transistors and one super Schottky diode is described and investigated. Flux noise measurements in an open loop have been performed using this readout.

Applied Physics Letters•Jan 16, 1995•2 citations
We describe the fabrication and characterization of super Schottky diodes which are used in the cryogenic part of a 3 GHz radio frequency superconducting quantum interference device (rf SQUID) readout electronics. The diodes were prepared on silicon wafers with an n-doping level of 5×1024 m−3. They exhibited sensitivities of 1500 V−1 at 4.2 K, and a noise equivalent power of 2×10−15 W/√Hz was measured at 2.1 GHz. Using planar niobium 3 GHz rf SQUIDs and a cooled rf amplifier, experiments have been performed to investigate the feasibility of these super Schottky diodes for demodulation of the SQUID rf signal voltage. A simple cryogenic rf SQUID readout, employing two transistors and one super Schottky diode is described and investigated. Flux noise measurements in an open loop have been performed using this readout.