Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physica C Superconductivity

Substrate resonator for HTS rf SQUID operation

Y. Zhang, Jürgen Schubert, N. Wolters, M. Banzet, W. Zander, Hans‐Joachim Krause

Published Aug 1, 2002• 52 citations
Publisher
DOI
10.1016/s0921-4534(02)00698-6

Related papers

Dependence of HTS rf-SQUID resonant frequency on its slit length (2)

Yuji Miyato

The Japan Society of Applied Physics•Jul 17, 2015•0 citations

Resonant frequency of high Tc rf-SQUID resonator

Akira Sakai

The Japan Society of Applied Physics•Jul 4, 2013•0 citations

Improved Characteristics of Integrated HTS rf SQUID on Bicrystal SrTiO3 Substrate Resonator Covered with HTS Thin Films in Flip-Chip Geometry

Yoshimi Hatsukade, Makoto TAKEMOTO, Ryuichi Kurosawa +2 more

Integrated high-temperature superconductor (HTS) radio-frequency (rf) superconducting quantum interference devices (SQUIDs) based on a bicrystal SrTiO3 substrate was investigated for application to magnetic contaminant detection. By covering a wide superconducting weak link and/or a slit of the YBa2Cu3O7-x SQUID with HTS thin films in flip-chip geometry, characteristics such as effective area and 1/f noise profile of the SQUID were successfully improved. By installing the covered SQUID in a magnetic contaminant detection system, it was demonstrated that the system can detect a tungsten ball of 15μm in diameter with a signal to noise ratio of about 2.

Physics Procedia•Jan 1, 2012•0 citations

HTS dc SQUID based rf amplifier: development concept

G.V. Prokopenko, S. V. Shitov, I. V. Borisenko +1 more

Physica C Superconductivity•Mar 1, 2002•3 citations

Low Frequency Noise Characteristic in HTS Step-Edge Junction Rf SQUID

S. K. H. Lam, Keith E. Leslie, Jeina Lazar

Rf SQUIDs have been fabricated on MgO substrate using step-edge YBCO junction. Ion beam etching as a post fabrication trimming process is routinely used to reduce (trim) the critical current of the junction for noise optimization. The white noise of SQUIDs with inductance,Ls= 157 pH can be reduced to 55μΦoHz−1/2after the trimming process. However, 1/f noise at low frequency has been found to be degraded after the trimming. Rf SQUIDs withLs= 130 pH were fabricated and measured. A similar noise performance was achieved in these SQUIDs down to 5 Hz without the need of trimming. The 1/f noise was found to be better than that of the trimmed SQUIDs.

IEEE Transactions on Applied Superconductivity•Mar 19, 2022•0 citations

Superconducting Microwave Resonators

Charles Neill, A. Megrant, M. Lenander +17 more

Bulletin of the American Physical Society•Mar 1, 2012•0 citations
Integrated high-temperature superconductor (HTS) radio-frequency (rf) superconducting quantum interference devices (SQUIDs) based on a bicrystal SrTiO3 substrate was investigated for application to magnetic contaminant detection. By covering a wide superconducting weak link and/or a slit of the YBa2Cu3O7-x SQUID with HTS thin films in flip-chip geometry, characteristics such as effective area and 1/f noise profile of the SQUID were successfully improved. By installing the covered SQUID in a magnetic contaminant detection system, it was demonstrated that the system can detect a tungsten ball of 15μm in diameter with a signal to noise ratio of about 2.
Rf SQUIDs have been fabricated on MgO substrate using step-edge YBCO junction. Ion beam etching as a post fabrication trimming process is routinely used to reduce (trim) the critical current of the junction for noise optimization. The white noise of SQUIDs with inductance,Ls= 157 pH can be reduced to 55μΦoHz−1/2after the trimming process. However, 1/f noise at low frequency has been found to be degraded after the trimming. Rf SQUIDs withLs= 130 pH were fabricated and measured. A similar noise performance was achieved in these SQUIDs down to 5 Hz without the need of trimming. The 1/f noise was found to be better than that of the trimmed SQUIDs.