Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of the IEEE

Superconductor analog-to-digital converters

Oleg A. Mukhanov, Deepnarayan Gupta, Alan M. Kadin, Vasili K. Semenov

Published Sep 20, 2004• 182 citations
Publisher

Abstract

Ultrafast switching speed, low power, natural quantization of magnetic flux, quantum accuracy, and low noise of cryogenic superconductor circuits enable fast and accurate data conversion between the analog and digital domains. Based on rapid single-flux quantum (RSFQ) logic, these integrated circuits are capable of achieving performance levels unattainable by any other technology. Two major classes of superconductor analog-to-digital converters (ADCs) are being developed - Nyquist sampling and oversampling converters. Complete systems with digital sampling at rates of /spl sim/20 GHz and above have been demonstrated using low-temperature superconductor device technology. Some ADC components have also been implemented using high-temperature superconductors. Superconductor ADCs have unique applications in true digital-RF communications, broadband instrumentation, and digital sensor readout. Their designs, test results, and future development trends are reviewed.

DOI
10.1109/jproc.2004.833660

Related papers

Superconductor analog-to-digital converters and their applications

Deepnarayan Gupta, Amol Inamdar, Dmitri E. Kirichenko +2 more

A wide variety of applications, ranging from radio-frequency (RF) receivers for broadband communications and signal detection, on earth and in space, would benefit from high-performance superconductor analog-to-digital converters (ADCs), based on magnetic flux quantization and fast switching Josephson junctions. Superconductor ADCs are capable of very high sample rates (100 GHz or more), very high linearity, and high sensitivity. Nyquist-rate ADCs use the high sample rate to digitize a wide instantaneous bandwidth (tens of GHz) and are useful for wideband spectrum monitoring as well as high-end scientific instrumentation. Delta and delta-sigma oversampling ADCs use the high linearity to achieve programmable trade-off between dynamic range and instantaneous bandwidth. These lowpass and bandpass ADCs have been used for direct digitization of narrower (tens to hundreds of MHz) RF bands in the 1-20 GHz range for a variety of communications, intelligence, electronic warfare, and radar applications. Another application area of these cryogenic ADCs is for outputs of cryogenic sensor arrays and terahertz mixers. Recent advances in various classes of ADCs for different applications are described.

IEEE MTT-S International Microwave Symposium digest•Jun 1, 2011•23 citations

Analysis of superconducting analog-to-digital converter front-end for improved resolution and large dynamic range

Pascal Febvre, Héla Gassara, Patricia Desgreys +1 more

Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).

•Apr 25, 2010•0 citations

The Testing of Superconductive ADCs in a Software-Defined Radio Base Stations

Abhishek Arun, Hans G. Kerkhoff, Marcel H.H. Weusthof

Software-Defined Radio (SDR), as explained in [1], is a promising concept for the wireless communication industry since the entire transceiver function can be implemented in software, avoiding the replacement of hardware each time the system has to be upgraded. However, the practical implementation of such a system is depended on the hardware, which consists of precise, ultra highspeed electronic devices such as Analog-to-Digital Converters (ADCs). The present state-of-the-art semiconductor ADCs cannot be used for the implementation of SDR in the near future [2]. Some of the factors that hamper the implementation are the requirements of very high speed of a few tens of GHz and the high resolution (e.g. 16 bits) at these speeds. On the other hand, using the Low-Temperature Superconducting (LTS) technology [3], which relays on the quantum mechanical property of superconductors, very high-speed electronic devices with the accuracy of a flux quantum, can be constructed. In a closed superconducting loop, the magnetic flux can exist only in discrete quantized amounts equal to the multiples of the magnetic flux quantum, φ0 = h/2e ~ 2.07x10 Wb. The theoretical speed limit of such a Rapid Single Flux Quantum (RSFQ) device is close to 1 THz [4]. These RSFQ circuits are the fastest of all devices built in any known technology. The basic building block of an RSFQ circuit is the Josephson Junction (JJ), which is formed when two superconductors are separated by an interface. Since RSFQ circuits work at extremely high speeds, testing and verification of such a device is a difficult and challenging task. Direct testing at these speeds is not possible at this moment. Furthermore, the costs of the equipment required for such tests would be extremely high. Hence methods have to be developed to reduce the requirements of external

•Nov 29, 2001•1 citation

Superconductor Digital-RF Transceiver Components

Oleg A. Mukhanov, Deepnarayan Gupta, Alan M. Kadin +3 more

Superconductive technology offers unparalleled digital and mixed-signal circuit performance, advancing digital processing from baseband to RF stages. This allows elimination of analog filters and mixers with generally poorly controlled phase performance, causing intersymbol interference limiting an overall communication system performance. HYPRES has been developing superconducting circuit components for application to digital RF communication transceivers. The components include low-pass and band-pass analog-to-digital converters, digital decimation and correlation-based filters, digital up/down-converters, and low-time-jitter clock sources. All of these are based on ultra-fast Rapid Single Flux Quantum (RSFQ) digital circuits, with clock rates up to 20 GHz demonstrated with 3-micron technology, and being scaled to 40 GHz and above. In this paper, we will discuss design and performance of some of these components. 1.

•Jan 1, 2006•7 citations

Superconductor analog to digital converter for sigint applications

Amol Inamdar, Deepnarayan Gupta, Timur V. Filippov +6 more

Superconductor analog-to-digital converters (ADC) offer high sensitivity and large dynamic range. We report recent advances in the low-pass phase-modulation-demodulation (PMD) oversampled analog-to-digital converter (ADC). The oversampled data from the PMD front-end are passed along with sampling clock to an on-chip digital filter. In the past, the maximum frequency of operation of such chips were limited by that of the digital decimation filter (DDF) to about 30 GHz. Recently, we have designed a chip that allows the PMD front-end to be clocked twice as fast as the DDF, resulting in sampling rates of 46.08 GHz and 29.44 GHz for chips with critical current densities of 4.5 and 1 kA/cm2respectively. We have also designed a new PMD front-end, with a quarter-rate quantizer (QRQ) that allows 18-20 dB extension of dynamic range. We are also pursuing a subranging ADC design with two PMD front-ends connected with fluxon amplifier and subtractor circuitry that promises a dynamic range extension by 25-30 dB. We report signal-to-noise ratio and spur-free dynamic range measurement results for various ADC chips, and project performance for future improvements.

IEEE Military Communications Conference (MILCOM)•Nov 1, 2008•9 citations

RSFQ Baseband Digital Signal Processing

Anna Herr

Ultra fast switching speed of superconducting digital circuits enable realization of Digital Signal Processors with performance unattainable by any other technology. Based on rapid-single-flux technology (RSFQ) logic, these integrated circuits are capable of delivering high computation capacity up to 30 GOPS on a single processor and very short latency of 0.1ns. There are two main applications of such hardware for practical telecommunication systems: filters for superconducting ADCs operating with digital RF data and recursive filters at baseband. The later of these allows functions such as multiuser detection for 3G WCDMA, equalization and channel precoding for 4G OFDM MIMO, and general blind detection. The performance gain is an increase in the cell capacity, quality of service, and transmitted data rate. The current status of the development of the RSFQ baseband DSP is discussed. Major components with operating speed of 30GHz have been developed. Designs, test results, and future development of the complete systems including cryopackaging and CMOS interface are reviewed.

IEICE Transactions on Electronics•Mar 1, 2008•7 citations
Ultrafast switching speed, low power, natural quantization of magnetic flux, quantum accuracy, and low noise of cryogenic superconductor circuits enable fast and accurate data conversion between the analog and digital domains. Based on rapid single-flux quantum (RSFQ) logic, these integrated circuits are capable of achieving performance levels unattainable by any other technology. Two major classes of superconductor analog-to-digital converters (ADCs) are being developed - Nyquist sampling and oversampling converters. Complete systems with digital sampling at rates of /spl sim/20 GHz and above have been demonstrated using low-temperature superconductor device technology. Some ADC components have also been implemented using high-temperature superconductors. Superconductor ADCs have unique applications in true digital-RF communications, broadband instrumentation, and digital sensor readout. Their designs, test results, and future development trends are reviewed.
A wide variety of applications, ranging from radio-frequency (RF) receivers for broadband communications and signal detection, on earth and in space, would benefit from high-performance superconductor analog-to-digital converters (ADCs), based on magnetic flux quantization and fast switching Josephson junctions. Superconductor ADCs are capable of very high sample rates (100 GHz or more), very high linearity, and high sensitivity. Nyquist-rate ADCs use the high sample rate to digitize a wide instantaneous bandwidth (tens of GHz) and are useful for wideband spectrum monitoring as well as high-end scientific instrumentation. Delta and delta-sigma oversampling ADCs use the high linearity to achieve programmable trade-off between dynamic range and instantaneous bandwidth. These lowpass and bandpass ADCs have been used for direct digitization of narrower (tens to hundreds of MHz) RF bands in the 1-20 GHz range for a variety of communications, intelligence, electronic warfare, and radar applications. Another application area of these cryogenic ADCs is for outputs of cryogenic sensor arrays and terahertz mixers. Recent advances in various classes of ADCs for different applications are described.
Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).
Software-Defined Radio (SDR), as explained in [1], is a promising concept for the wireless communication industry since the entire transceiver function can be implemented in software, avoiding the replacement of hardware each time the system has to be upgraded. However, the practical implementation of such a system is depended on the hardware, which consists of precise, ultra highspeed electronic devices such as Analog-to-Digital Converters (ADCs). The present state-of-the-art semiconductor ADCs cannot be used for the implementation of SDR in the near future [2]. Some of the factors that hamper the implementation are the requirements of very high speed of a few tens of GHz and the high resolution (e.g. 16 bits) at these speeds. On the other hand, using the Low-Temperature Superconducting (LTS) technology [3], which relays on the quantum mechanical property of superconductors, very high-speed electronic devices with the accuracy of a flux quantum, can be constructed. In a closed superconducting loop, the magnetic flux can exist only in discrete quantized amounts equal to the multiples of the magnetic flux quantum, φ0 = h/2e ~ 2.07x10 Wb. The theoretical speed limit of such a Rapid Single Flux Quantum (RSFQ) device is close to 1 THz [4]. These RSFQ circuits are the fastest of all devices built in any known technology. The basic building block of an RSFQ circuit is the Josephson Junction (JJ), which is formed when two superconductors are separated by an interface. Since RSFQ circuits work at extremely high speeds, testing and verification of such a device is a difficult and challenging task. Direct testing at these speeds is not possible at this moment. Furthermore, the costs of the equipment required for such tests would be extremely high. Hence methods have to be developed to reduce the requirements of external
Superconductive technology offers unparalleled digital and mixed-signal circuit performance, advancing digital processing from baseband to RF stages. This allows elimination of analog filters and mixers with generally poorly controlled phase performance, causing intersymbol interference limiting an overall communication system performance. HYPRES has been developing superconducting circuit components for application to digital RF communication transceivers. The components include low-pass and band-pass analog-to-digital converters, digital decimation and correlation-based filters, digital up/down-converters, and low-time-jitter clock sources. All of these are based on ultra-fast Rapid Single Flux Quantum (RSFQ) digital circuits, with clock rates up to 20 GHz demonstrated with 3-micron technology, and being scaled to 40 GHz and above. In this paper, we will discuss design and performance of some of these components. 1.
Superconductor analog-to-digital converters (ADC) offer high sensitivity and large dynamic range. We report recent advances in the low-pass phase-modulation-demodulation (PMD) oversampled analog-to-digital converter (ADC). The oversampled data from the PMD front-end are passed along with sampling clock to an on-chip digital filter. In the past, the maximum frequency of operation of such chips were limited by that of the digital decimation filter (DDF) to about 30 GHz. Recently, we have designed a chip that allows the PMD front-end to be clocked twice as fast as the DDF, resulting in sampling rates of 46.08 GHz and 29.44 GHz for chips with critical current densities of 4.5 and 1 kA/cm2respectively. We have also designed a new PMD front-end, with a quarter-rate quantizer (QRQ) that allows 18-20 dB extension of dynamic range. We are also pursuing a subranging ADC design with two PMD front-ends connected with fluxon amplifier and subtractor circuitry that promises a dynamic range extension by 25-30 dB. We report signal-to-noise ratio and spur-free dynamic range measurement results for various ADC chips, and project performance for future improvements.
Ultra fast switching speed of superconducting digital circuits enable realization of Digital Signal Processors with performance unattainable by any other technology. Based on rapid-single-flux technology (RSFQ) logic, these integrated circuits are capable of delivering high computation capacity up to 30 GOPS on a single processor and very short latency of 0.1ns. There are two main applications of such hardware for practical telecommunication systems: filters for superconducting ADCs operating with digital RF data and recursive filters at baseband. The later of these allows functions such as multiuser detection for 3G WCDMA, equalization and channel precoding for 4G OFDM MIMO, and general blind detection. The performance gain is an increase in the cell capacity, quality of service, and transmitted data rate. The current status of the development of the RSFQ baseband DSP is discussed. Major components with operating speed of 30GHz have been developed. Designs, test results, and future development of the complete systems including cryopackaging and CMOS interface are reviewed.